REPRESENTED BY:
ALTRU-V (A Division of UVDI)
26145 Technology Drive
Valencia, CA 91355
Tel 877-PUREUVC (877-787-3882)
Tel 661-295-8140
Fax 661-257-4698
V-RAY™ SUS
Easily Installed into hard to access systems delivering continuous
irradiation for improved heat exchange efficiency while reducing
foul odor, drain pain overflows and expensive coil cleanings!
UVC Fixturing – Fixturing consists of a
lamp, lamp clasps, UVC resistant wiring
harness, power supply and power supply
housing.
UL Listed and labeled for use in air-streams
of 55–135°F. They are capable of pro-
ducing the specified output and organism
destruction as listed under Irradiation and
Intensity above at no more than 13 Watts
of power consumption for each square foot
of treated, cross sectional area.
vb:
uv_>
1
Lamps – Each lamp contains no more
than 5 milligrams of mercury. Lamp life
is 9000 hours with no more than a 20%
output loss at the end of the lamps life.
Lamps are constructed with UVC resistant
bases and do not produce ozone. When
used for surface irradiation, the lamp
selected will be equal to or no less than
90% of the coil width.
• 4-lamp sizes (12", 21", 33" and 61")
• Lowest mercury content available
• UV output regulated to keep levels
within ACGIH and NIOSH exposure
guidelines (patent pending) thus
–Extending lamp life and
–Ensuring safe exposure limits for
room occupants or materials
• UL recognized components, ETL Listed
• Ideal for any vertical or horizontal
system
• Ease of installation – Simple Lamp
Clasps (magnetic Lamp Clasp optional)
Installation – Fixturing are electrically
terminated to within factory supplied ballast
housings to meet NEC and local codes.
Lamps should be mounted to irradiate the
intended surface(s) as well as all of the
available line of sight airstream by proper
placement and incident angle reflection.
2
Irradiation – Fixtureless lamps are to be
installed in sufficient quantity and in such
a manner as to provide an equal distribu-
tion of UVC energy. When installed, the
UVC energy produced will be of the lowest
possible reflected and shadowed losses.
Note: the applied energy and its distribu-
tion shall be verifiable using third
Safety – To protect maintenance
personnel, all access panels and doors
to the UVC assembly and/or within view
of the UVC assembly must include mechan-
ical interlock switche(s) to insure that the
UVC assembly will be de-energized when
any of these accesses are opened.
• Single point electrical connection
• UVC resistant materials
V-Ray SUS: 12”, 21”, 33”, 61” Lamp Sizes.
1. V-Ray Bulb Lengths: 61”*, 36”, 24” and 12”*.
2. V-Ray Magnetic Clip
party algorithms.
• Screw terminals for easy field wiring
Intensity – The minimal UVC energy
striking a surface is sufficient to continu-
ously destroy a monolayer of mold and
bacteria in less than six hours when at
55–135°F. The third party modeling shall
be available to determine the destruction
time for at least four of the most common
fan coil surface microbes.
• Remotely located power source
offering ease of installation and
mounting options
• Restores air handling unit to near
optimal operating capacities
• Can lower energy costs for restored
systems
• Reduces costly maintenance and
cleaning programs
• Eliminates foul system odors (dirty
sock syndrome)
• Has one of the lowest ownership
costs in the industry
• Improves indoor air quality by
destroying system microbes
• Will not harm building occupants,
equipment or furnishings
All ALTRU-V products are designed to transform HVAC efficiency, maintenance
and longevity. By applying real science, the relentless cleaning power of UV and
the most affordable products by UVDI, optimal HVAC maintenance solutions can
replace outdated mechanical and chemical cleanings that can be both costly and
dangerous and shorten equipment life. The results are lower operating costs,
safer environments for maintenance personnel and occupants, as well as
documented cleaner air.
Lamp Clasp – Lamp Clasps may be
permanently or magnetically affixed to the
irradiated cavity. They are constructed of
high memory, plated steel for maximum
holding power and corrosion resistance.
Lamp Wire – Is of sufficient length to
facilitate lamp connection to a remotely
located ballast. It includes a grommet to
facilitate safe passage through sheet metal
and into the ballast housing. Lamps are
capable of being mounted anywhere in the
system and/or as shown on the plans.
ALTRU-V’s V-Ray™ provides unique electronically controlled energy output (patent
pending) at registers and grills to meet acceptable levels as recommended by the
National Institute for Occupational Safety and Health (NIOSH) and the American
Conference of Governmental Industrial Hygienists (ACGIH), yet it delivers the
proper amount of energy necessary to control the growth of micro-organisms such
as mold and bacteria.
Model No.
VRSUS 12
VRSUS 21
VRSUS 33
VRSUS 61
VR MC
Description
Lamp Dim.
12” *
21”
Electrical
Weight
3 lbs.
P/N
• One-year warranty on both the fixture
and the lamp
V-Ray UVC Fixture
V-Ray UVC Fixture
V-Ray UVC Fixture
V-Ray UVC Fixture
V-Ray UVMagClasp (Pair)
100–277Vac, 50-60 Hz, 11 Watts
100–277Vac, 50-60 Hz, 15 Watts
100–277Vac, 50-60 Hz, 21 Watts
100–277Vac, 50-60 Hz, 31 Watts
—
23-1012
23-1021
23-1033
23-1061
23-1063
Power Supply – Power supplies are of
the high efficiency electronic type, matched
to the lamp and designed to optimize UVC
photon production and reliability. They are
3 lbs.
33”
3 lbs.
61” *
—
5 lbs.
0.5 lbs.
* The V-Ray 12” and 64” units are non-inventory items subject to varying lead times.
Hg-LAMP CONTAINS MERCURY. Manage in Accord with
Specifications subject to change without notice.
Copyright 2004 UVDI. ALTRU-V and V-Ray SUS are trademarks owned by UVDI. Patent Pending. 23-1004 Rev A
|