User’s Guide
TN-GLC-xx-xx and TN-CWDM-SFP-1xx0 Cisco
CompatibleSmall Form Factor Pluggable (SFP)
Transceiver Modules**
The Transition Networks TN-GLC-xx-xx and TN-CWDM-
SFP-1xx0 series small form factor pluggable (SFP) transceiver
TN-GLC-T
modules are designed to install in any SFP port, allowing for1000Base-T, 1000Base-SX
or 1000Base-LX interfaces to the network through the SFP connector. The TN-GLC-xxx
and TN-CWDM-SFP-1xx0 transceivers are designed for bi-directional serial-optical data
communications such as Gigabit Ethernet or fiber channel at speeds up to 2.125 Gbps.
TN-GLC-SX-MM
Part Number Port Description
TN-GLC-BX-0
TN-CWDM-SFP-1xx0
TN-GLC-T
1000Base-T , RJ-45
100m (328 ft)*
TN-GLC-SX-MM
1000Base-SX, duplex LC, 850 nm,
220 m (722 ft)* on 62.5/125 µm fiber
550 m (1840 ft)* on 50/125 µm fiber
TN-GLC-SX-MM-2K 1000Base-SX, duplex LC 1300 nm, extended multimode
up to 2 km (1.2 miles)*
TN-GLC-LH-SM
TN-GLC-BX-U
TN-GLC-BX-D
1000Base-LX, 1310 nm, single mode
10 km (6.2 miles)*
1000Base-BX, Simplex LC 1310 nm Tx/1490 nm Rx nm,
single mode, single fiber 10 km (6.2 miles)*
1000Base-BX, Simplex LC 1490 nm Tx/1310 nm Rx nm,
single mode, single fiber 10 km (6.2 miles)*
*Unless otherwise indicated, the distances listed are the typical maximum cable
distance. The actual maximum cable distances are dependent upon the physical
characteristics of the network installation.
**Transition Networks' SFP modules fully comply with the Multi-Sourcing Agreement
(MSA). This compliance allows our SFP modules to be used in other MSA compliant
SFP platforms without problems. In
Installation . . . . . . . . . . . . . . . . . . . . . . . . .3
Cable Specifications . . . . . . . . . . . . . . . . .5
Technical Specifications . . . . . . . . . . . . . .8
Contact Us . . . . . . . . . . . . . . . . . . . . . . . . .9
Compliance Information . . . . . . . . . . . . .11
addition, TN SFP modules specified in
this manual are also compatible with all
Cisco SFP-based routers and switches, as
well as its IOS software. TN SFP
modules ARE NOT Cisco OEM brand
modules.
TN-GLC-xx-xx SFPs
Installing the fiber cables
Cable Specification
Copper cable (Category 5 -- minimum requirement)
1. Locate or build 1000Base-SX-compliant or 1000Base-LX-compliant fiber
cable with male TX to RX connectors installed at both ends.
• Gauge = 24 to 22 AWG; Attenuation = 22.0 dB /100m @ 100 MHz
• Straight-through OR crossover cable may be used.
• Shielded twisted-pair (STP) OR unshielded twisted-pair (UTP) may be used
• All pin pairs (1&2, 3&6, 4&5, 7&8) are active in a gigabit network.
• Use only dedicated wire pairs for the active pins; e.g., blue/white &
white/blue,
2. Install the fiber cable as shown below.
Connect fiber cable
to media converter
as shown.
Connect fiber cable
to other device
(media converter,
hub, etc.) as shown
orange/white & white/orange, etc.
• Do not use flat or silver satin wire.
RX
TX
RX
TX
Straight-Through Cable
Crossover Cable
1
2
1
2
1
2
1
2
Twisted Pair #1
Twisted Pair #2
Twisted Pair #1
Twisted Pair #2
3
6
3
6
3
6
3
6
5
Tech Support: 1-800-260-1312 -- International: 00-1-952-941-7600 -- (24 hours)
[email protected] -- Click the “Transition Now” link for a live Web chat.
4
TN-GLC-xx-xx SFPs
Fiber cable -- continued
Fiber cable
TN-GLC-FE-100FX
TN-GLC-GE-100FX
1300 nm multimode
1300 nm multimode
min: -23.5 dBm
min: -32.0 dBm
8.5 dB
The physical characteristics must meet or exceed IEEE 802.3z™ specifications.
Singlemode fiber (recommended):
Multimode fiber (recommended):
Multimode fiber (optional):
9 µm
Fiber Optic Transmitter Power:
max: -14.0 dBm
max: -8.0 dBm
62.5/125 µm
Fiber Optic Receiver Sensitivity:
Link Budget:
100/140, 85/140, 50/125 µm
TN-GLC-SX-MM
850 nm multimode
TN-GLC-FE-100LX
1310 nm single mode
Fiber Optic Transmitter Power:
Fiber Optic Receiver Sensitivity:
Link Budget:
min: -9.5 dBm
min: -18.0 dBm
8.5 dB
max: -3.5 dBm
max: -1.0 dBm
Fiber Optic Transmitter Power:
Fiber Optic Receiver Sensitivity:
Link Budget:
min: -15.0 dBm
min: -34.0 dBm
19.0 dB
max: -8.0 dBm
max: -0.0 dBm
TN-GLC-SX-MM-2k
1300 nm multimode
min: -9.0 dBm
min: -19.0 dBm
18.0 dB
TN-GLC-ZX-SM
1550 nm single mode
Fiber Optic Transmitter Power:
Fiber Optic Receiver Sensitivity:
Link Budget:
max: -1.0dBm
max: -1.0 dBm
Fiber Optic Transmitter Power:
Fiber Optic Receiver Sensitivity:
Link Budget:
min: 0.0 dBm
min: -24.0 dBm
24 dB
max: +5.0 dBm
max: -3.0 dBm
TN-GLC-LH-SM
1310 nm singlemode
TN-CWDM-SFP-1xx0
Fiber Optic Transmitter Power:
Fiber Optic Receiver Sensitivity:
Link Budget:
1270nm -1610nm single mode
Fiber Optic Transmitter Power:
Fiber Optic Receiver Sensitivity:
Link Budget:
min: -9.5 dBm
min: -20.0 dBm
10.5 dB
max: -3.0 dBm
max: -3.0 dBm
min: 0.0 dBm
min: -25.0 dBm
25 dB
max: +5.0 dBm
max: -3.0 dBm
TN-GLC-BX-U
1310 nm Tx/1490 nm Rx single mode
1490 nm Tx/1310 nm Rx single mode
min: -9.0 dBm
min: -21.0 dBm
12.0 dB
For the most up-to-date information on the TN-GLC-xx-xx transceiver module, view
Product is certified by the manufacturer to comply with DHHS Rule 21/CFR,
Subchapter J applicable at the date of manufacture.
TN-GLC-BX-D
Fiber Optic Transmitter Power:
Fiber Optic Receiver Sensitivity:
Link Budget:
max: -1.0 dBm
max: -1.0 dBm
WARNING: Visible and invisible laser radiation when open. Do not stare into beam
or view directly with optical instruments. Failure to observe this warning could result
damage to your eyes or blindness.
WARNING: Use of controls, adjustments or the performance of procedures other than
those specified herein could result in hazardous radiation exposure.
TN-GLC-BX-U-40
1310 nm Tx/1490 nm Rx single mode
1490 nm Tx/1310 nm Rx single mode
min: -3.0 dBm
min: -23.0 dBm
20.0 dB
TN-GLC-BX-D-40
Fiber Optic Transmitter Power:
Fiber Optic Receiver Sensitivity:
Link Budget:
max: +2.0 dBm
max: -1.0 dBm
The fiber optic transmitters on this device meet Class I Laser safety requirements per
IEC-825/CDRH standards and comply with 21 CFR1040.10 and 21CFR1040.11.
TN-GLC-BX-U-60
1310 nm Tx/1490 nm Rx single mode
1490 nm Tx/1310 nm Rx single mode
min: -2.0 dBm
min: -25.0 dBm
23.0 dB
TN-GLC-BX-D-60
Fiber Optic Transmitter Power:
Fiber Optic Receiver Sensitivity:
Link Budget:
max: +4.0 dBm
max: -1.0 dBm
TN-GLC-FE-100BX-U
TN-GLC-FE-100BX-D
Fiber Optic Transmitter Power:
Fiber Optic Receiver Sensitivity:
Link Budget:
1310 nm Tx/1550 nm Rx single mode
1550 nm Tx/1310 nm Rx single mode
min: -14.0 dBm
min: -32.0 dBm
18.0 dB
max: -8.0 dBm
max: -0.0 dBm
7
Tech Support: 1-800-260-1312 -- International: 00-1-952-941-7600 -- (24 hours)
[email protected] -- Click the “Transition Now” link for a live Web chat.
6
TN-GLC-xx-xx SFPs
Technical Specification
For use with Transition Networks Model TN-GLC-xxx or equivalent.
Contact Us
Technical support
Technical support is available 24 hours a day.
U.S.A. and Canada: 1-800-260-1312
Standard:
IEEE 802.3 2003; ANSI X3.297-1997
TN-GLC-FE-xxx and TN-GLC-GE-xxx: Compiant with
IEEE 802.3 100Base-Fx; IEEE802.3ah 100Base-Bx;
Intermediate - Reach Sonet OC-3/SDH STM-1 (s-1-1)
International:
00-1-952-941-7600
Transition now
TN-GLC-xx-xx and TN-CWDM-SFP-1xx0 modules:
IEEE 802.3z Gigabit Ethernet; FC-1x/2x SM-LC-L FC-PI.
TN-GLC-T modules: Compliant with IEEE 802.32 Gigabit
Ethernet (1000Base-T)
Chat live via the Web with Transition Networks Technical Support.
Compliant with
Web-Based seminars
Transition Networks provides seminars via live web-based training.
Output wavelength
Dimensions:
-6.0 < λc < +7.5 nm
0.52 x 2.18 x 0.33’’ (13.4 x 55.5 x 8.5 mm, Fiber)
0.95 x 2.8 x 0.54” (14-0 x 71.1 13.7 mm, Copper)
1 oz. (28 g) approximately
E-Mail
Ask a question anytime by sending an e-mail to our technical support staff.
Weight:
Power:
3.3V, Fiber 0.66 W; Copper 1.0 W
0°C to 70°C (32°F to 158° F )
-40°C to 85°C (-40° to 185°F)
5% to 95%, non-condensing
0 to 10,000 feet
Operating Temp:
Storage Temp:
Humidity:
Altitude:
Address
Transition Networks
10900 Red Circle Drive
Minnetonka, MN 55343, U.S.A.
telephone:
toll free:
fax:
952-941-7600
800-526-9267
952-941-2322
Warranty:
Lifetime
Note: Transition Networks' SFP modules fully comply with the Multi-Sourcing
Agreement (MSA). This compliance allows our SFP modules to be used in
other MSA compliant SFP platforms without problems. In addition, TN SFP
modules are also compatible with all Cisco SFP-based routers and switches, as
well as its IOS software and SMARTnet. TN SFP modules ARE NOT Cisco
OEM brand modules.
9
Tech Support: 1-800-260-1312 -- International: 00-1-952-941-7600 -- (24 hours)
[email protected] -- Click the “Transition Now” link for a live Web chat.
8
TN-GLC-xx-xx SFPs
Compliance Information
Declaration of Conformity
CE Mark: IEC-60825; FDA 21; CFR 1040.10 and 1040.11
Name of Mfg:
Transition Networks
10900 Red Circle Drive, Minnetonka MN 55343 U.S.A.
TN-GLC-xx-xx Series Transceiver Modules
TN-GLC-T, TN-GLC-SX-MM, N-GLC-SX-MM-2k,
TN-GLC-LH-SM, TN-GLC-BX-U, TN-GLC-BX-D,
TN-GLC-BX-U-40, TN-GLC-BX-D-40, TN-GLC-BX-U-60,
TN-GLC-BX-D-60, TN-GLC-FE-100BX-U,
TN-GLC-FE-100BX-D, TN-GLC-FE-100FX,
TN-GLC-FE-100LX, TN-GLC-GE-100LX, TN-GLC-ZX-SM,
TN-CWDM-SFP-1xx0
FCC regulations
Model:
Part Number(s):
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference, in which
case the user will be required to correct the interference at the user's own expense.
Canadian regulations
Regulation:
Purpose:
EMC Directive 89/336/EEC
To declare that the TN-GLC-xxx to which this declaration refers
is in conformity with the following standards:
This digital apparatus does not exceed the Class A limits for radio noise for digital apparatus set out
on the radio interference regulations of the Canadian Department of Communications.
Le présent appareil numérique n'émet pas de bruits radioélectriques dépassant les limites
applicables aux appareils numériques de la Class A prescrites dans le Règlement sur le brouillage
radioélectrique édicté par le ministère des Communications du Canada.
IEC 60825-1; IEC60825-2; FC1X/2X SM-LC-L FC-PI; IEEE 802.3z 2003; ANSI X3.297
1997; Class A; FDA 21; CFR1040.10; CFR1040.11
I, the undersigned, hereby declare that the equipment specified above conforms to the above
Directive(s) and Standard(s).
October 2008____
European regulations
Warning
Stephen Anderson, Vice-President of Engineering
Date
This is a Class A product. In a domestic environment this product may cause radio interference in
which case the user may be required to take adequate measures.
Achtung !
Dieses ist ein Gerät der Funkstörgrenzwertklasse A. In Wohnbereichen können bei Betrieb dieses
Gerätes Rundfunkstörungen auftreten. In diesem Fäll ist der Benutzer für Gegenmaßnahmen
verantwortlich.
Attention !
Ceci est un produit de Classe A. Dans un environment domestique, ce produit risque de créer des
interférences radioélectriques, il appartiendra alors à l'utilsateur de prende les measures spécifiques
appropriées.
In accordance with European Union Directive 2002/96/EC of the European Parliament
and of the Council of 27 January 2003, Transition Networks will accept post usage
returns of this product for proper disposal. The contact information for this activity can
be found in the 'Contact Us' portion of this document.
CAUTION: RJ connectors are NOT INTENDED FOR CONNECTION TO THE
PUBLIC TELEPHONE NETWORK. Failure to observe this caution could result in
damage to the public telephone network.
Der Anschluss dieses Gerätes an ein öffentlickes Telekommunikationsnetz in den EG-
Mitgliedstaaten verstösst gegen die jeweligen einzelstaatlichen Gesetze zur Anwendung der
Richtlinie 91/263/EWG zur Angleichung der Rechtsvorschriften der Mitgliedstaaten über
Telekommunikationsendeinrichtungen einschliesslich der gegenseitigen Anerkennung ihrer
Konformität.
11
Tech Support: 1-800-260-1312 -- International: 00-1-952-941-7600 -- (24 hours)
[email protected] -- Click the Transition Now link for a live Web chat.
10
TN-GLC-xx-xx SFPs
Trademark notice
All trademarks and registered trademarks are the property of their respective owners.
Copyright restrictions © 2004 Transition Networks. All rights reserved. No part of this work may
be reproduced or used in any form or means (graphic, electronic, mechanical) without written
permission from Transition Networks.
Printed in the U.S.A. 33389.D
12
|