Toshiba Security Camera IK 6420A User Manual

• The CAUTION label, shown on the left,

is attached on the camera.

IMPORTANT SAFEGUARDS

1. Read Instructions

13. Lightning

All the safety and operating instructions should be

read before the product is operated.

For additional protection on this video product during

a lightning storm, or when it is left unattended and

unused for long periods of time, unplug it from the

wall outlet and disconnect the power supply and cable

system.This will prevent damage to the video product

due to lightning and power-line surges. If lightning

occurs, do not touch the unit or any connected cables

in order to avoid electric shock.

CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK.

DO NOT REMOVE COVER (OR BACK).

NO USER SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

2. Retain Instructions

The safety instructions and instruction manual should

be retained for future reference.

3. Warnings

Comply with all warnings on the product and in the

instruction manual.

The lightening flash with arrowhead

WARNING :

symbol, within an equilateral triangle,

is intended to alert the user to the

presence of uninsulated “dangerous

voltage”within the product’s enclosure

that may be of sufficient magnitude to

constitute a risk of electric shock to

persons.

14. Overloading

4. Follow Instructions

Follow all operating and use instructions.

5. Cleaning

Disconnect this video product from the power supply

before cleaning.

6. Attachments

TO REDUCE THE RISK OF FIRE OR

ELECTRIC SHOCK, DO NOT EXPOSE

THIS APPLIANCE TO RAIN OR

MOISTURE.

Do not overload the power supply or extension cords

as this can result in a risk of fire or electric shock.

15. Object and Liquid Entry

Never push objects of any kind into this video product

through openings as they may touch dangerous

electrical points or short-out parts that could result in

a fire or electrical shock. Never spill liquid of any kind

on the video product.

Do not use attachments not recommended by the

video product manufacturer as they may cause

hazards.

CAUTION :

CONNECT 24V AC UL LISTED CLASS 2

16. Servicing

7. Water and Moisture

POWER SUPPLY.

The exclamation point within an

equilateral triangle is intended to alert

the user to the presence of important

operating and maintenance (servicing)

instructions in the literature

accompanying the appliance.

Do not attempt to service this video product yourself

as opening or removing covers may expose you to

dangerous electrical or other hazards. Refer all

servicing to qualified service personnel.

Do not use this video product near water. Some

examples are: near a bath tub, wash bowl, kitchen

sink, or laundry tub, in a wet basement, or near a

swimming pool.

FIELD INSTALLATION MARKING :

THIS INSTALLATION SHOULD BE

MADE BY A QUALIFIED SERVICE

PERSON AND SHOULD CONFORMTO

ALL LOCAL CODES.

17. Damage Requiring service

8. Accessories

Disconnect this video product from the power supply

and refer servicing to qualified service personnel

under the following conditions.

Do not place this video product on an unstable cart,

stand, tripod, bracket or table.The video product may

fall, causing serious injury to a person, or serious

damage to the product. Use only with stand, tripod,

bracket, or table recommended by the manufacturer,

or sold with the video product. Any mounting of the

product should follow the manufacturer’s instructions,

and should use a mounting accessory recommended

by the manufacturer.

a. When the power-supply cord or plug is damaged.

b. If liquid has been spilled, or objects have fallen into

the video product.

c. If the video product has been exposed to rain or

water.

d. If the video product does not operate normally by

following the operating instructions in the instruction

manual. Adjust only those controls that are covered

by the instruction manual as an improper adjustment

of other controls may result in damage and will often

require extensive work by a qualified technician to

restore the video product to its normal operation.

e.If the video product has been dropped or the cabinet

has been damaged.

9. Ventilation

This video product should never be placed near or

over a radiator or heat register.If this product is placed

in a built in installation verify that there is proper

ventilation so that the camera temperature operates

within the recommended temperature range.

10. Power Sources

FCC (USA)-INFORMATION

NOTE : This equipment has been tested and found to comply with the limits for a Class A

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a

commercial environment. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. Operation of this equipment in a residential

area is likely to cause harmful interference in which case the user will be required to correct the

interference at his own expense.

This video product should be operated only from the

type of power source indicated on the information

label. If you are not sure of the type of power supply

at your location, consult your product dealer.

11. Power-Cord Protection

f. When the video product exhibits a distinct change

in performance which indicates a need for service.

18. Replacement Parts

When replacing parts be sure the service technician

uses parts specified by the manufacturer or have the

same characteristics as the original part.

Unauthorized substitutions may result in fire, electric

shock or other hazards.

Power cords should be routed so that they are not

likely to be walked on or pinched by items placed upon

or against them. Pay particular attention to cords at

plugs, screws and the point where they exit the

product.

USER-INSTALLER CAUTION : Your authority to operate this FCC verified equipment could

be voided if you make changes or modifications not expressly approved by the party.

19. Safety Check

Upon completion of any service or repairs to this video

product, ask the service technician to perform safety

checks to determine that the video product is in proper

operating condition.

12. Installation

Install this video product on a secure part of the ceiling

or wall.If installed on a unsecured location the camera

could fall causing injury and damage.

- 2 -

- 3 -

4. CAMERA INSTALLATION

5. CONNECTIONS AND OPERATIONS

Notes on connecting

• Power plugs of connected equipment must be disconnected before camera

installation.

• A 75-ohm coaxial cable with connector (3C-2V or 5C-2V) is required for standard

connection.

Wall

9.5 (0.37)

Installation Example

• For details of wiring and operation of equipment to be connected, refer to their

operation manuals.

• Lens, power supply with cable, connectors and coaxial cable are not supplied with

the camera.

1/4"-20UNC

5-1. Basic connection Single system configuration

MONITOR TV

112 (4.41)

15 (0.59)

CAMERA

The Installation example is for reference only.

Mounting bracket is not included.

Dimensions : mm (inch)

24V AC UL Listed Class 2 power supply

12V DC power supply

120V AC

(*) Recommend power cord is twisted pair line

with a minimum wire size of 18 AWG.

CAUTION: Never input 24V AC and 12V DC at the same time.

Do not overload power supply

The recommended power supplies for this camera are 6 watt minimum for each 24V

AC UL Listed Class 2 power supply or 12V DC power supply.

- 6 -

- 7 -

5-2. Line-Lock Control

• Matching the vertical synchronization with the power frequency is called the Line-Lock.

6. LENS

• This function is activated when the LL switch is set to ON.

Back-Focus Adjusment

Back-Focus is adjusted at the factory to accommodate most standard lenses.

Sometimes, slight adjustment to the camera back-focus is

necessary.

OFF

Focus Lock Screw

Loosen the Focus Lock Screw. Achieve a clear image by

rotating the focus ring.

Tighten the Focus Lock Screw.

• When two or more cameras are switched by the video switcher for viewing by a monitor TV, the

vertical sync. phase can be locked to the power frequency, and a stable vertical sync. is obtained

without being disturbed at the time of switching.

Focus ring

IRIS

MONITOR TV

CAMERA1

Auto-iris Lens

This camera supports two types of auto-iris lens: Video

and DC (direct drive) types. Connect the auto-iris

connector plug to the IRIS terminal on the side of the

camera. Refer to the chart below for correct wiring and

set up.

CAMERA2

VIDEO SWITCHER

TO 24V AC UL Listed

Class 2 power supply

Auto-iris lens

Note:

• The camera is synchronized to the power frequency of 60 ±1 Hz covering a normal fluctuation of

the power frequency. However, the camera may not cover a large fluctuation caused from the

power generated by an engine generator, etc.

• It takes about 10 seconds or more until a stable synchronization is obtained after the power is

turned on.This is normal, because several seconds are required to stabilize the camera against

power noise.

Video IRIS

Lens

Direct Drive

IRIS Lens

+12V

Damp – (y)

IRIS terminal

Damp + (γ)

Driver + (wh)

Driver – (g)

VIDEO

GND

• Refer to "7. LINE-LOCK PHASE" for adjustment.

Camera Side

IRIS Switch

VIDEO position DC position

5-3. Operation

1. Mount the lens to the camera.

2. Mount the camera to the camera mount.

Caution: If the lens weight is more than 2.2 lbs (1 kg) mount the lens to the camera mount.

Refer to section 6 for lens types and connection.

3. Connect the cables and support equipment to obtain a picture.

4. Adjust the lens aperture (if applicable).

- 8 -

- 9 -

7. LINE-LOCK PHASE

8. AUTOMATIC ELECTRONIC SHUTTER (AES)

If two or more cameras within a system have

different AC line phases are switched by the video

switcher, the picture on the monitor TV will fluctuate

vertically.

Exposure time is controlled automatically within a range of 1/60 sec. to 1/100000 sec. to obtain an

adequate signal when the IRIS switch is moved to AES.

When the back panel switch is turned to VIDEO or DC, the exposure time is fixed 1/60 sec.

Connect 24V AC input lines of all cameras so that

they all share the same phase.

If you still have vertical fluctuation, adjust the

V.PHASE controller.

9. BACKLIGHT COMPENSATION (BLC)

V. PHASE CONTROLLER

To activate backlight compensation, set the BLC switch to ON.

Note:

OFF

• Refer to “5-2. Line-Lock Control”.

BLC

When the automatic electronic iris feature is used with an auto iris lens, the exposure adjustment

is automatically performed so that a best picture is obtained at a monitor zone of about 50% in

horizontal and about 50% in vertical direction.

This function is effective when a strong light enters the portion other than this zone and auto iris

lens closes and darkens the area to view.

(Monitor screen)

50%

- 10 -

- 11 -

10. NOTES ON USE AND INSTALLATION

12. SPECIFICATIONS

• Do not aim the camera at the sun

Never aim the camera at the sun even with the camera power off.

IK-6210A

24V AC ~ ±10% 60Hz / 12V DC ±10%

Power

• Do not shoot intense light

Intense light such as a spotlight may cause a bloom or smear. A vertical stripe may appear on

the screen. However, this is not a malfunction.

Power consumption

Image sensor

3.5W with Al lens

1/3 inch CCD image sensor

• Treat the camera with care

Do not drop the camera or subject it to intense vibration.

Image pickup area

Effective picture element

Scanning system

Scanning frequency

Synchronization

Resolution

0.194 inch (4.92 mm) horizontal x 0.145 inch (3.69 mm) vertical

510 horizontal x 492 vertical

• Never touch internal parts

Do not touch the internal parts of the camera other than the parts specified.

2:1 interlace NTSC Standard TV system

15.75 KHz horizontal 60 Hz vertical

Line-Lock, Internal manually switchable

350 Horizontal TV lines

• Do not splash water on the camera

Install the camera where the camera can be kept dry. If the camera gets wet, turn off the power

and contact your dealer.

• Keep the camera installation away from video noise

If cables are wired near electric lighting wires or a TV set, noise may appear in images. In this

event, relocate cables or reinstall equipment.

Minimum illuminance of subject 0.2 lux (F1.2, More than 10% of image output γ = 0.45)

• Check the ambient temperature and humidity

S/N

50 dB or more (weight ON)

Avoid using the camera where the temperature is hotter or colder than the specified operating

range. Doing so could affect the internal parts or cause the image quality to deteriorate. Special

care is required to use the camera at high temperature and humidity.

Video output

VBS 1.0 V p-p / 75 ohms, composite

75 ohms unbalanced

Output impedance

White balance

Iris control

• Should you notice any trouble

Automatic (2500 K to 10,000 K)

Video Out / Iris Driver Circuit Built in

Average AGC (26 dB)

If any trouble occurs while you are using the camera, turn off the power and contact your dealer.

If you continue to use the camera when there is something wrong with it, the trouble may get

much worse and an unpredictable problem may occur.

Gain control

Backlight compensation

Lens mount

Manual ON/OFF switching, center zone light measuring system

CS mount

11. IN CASE OF PROBLEMS

Ambient temperature

Ambient humidity

Weight

14˚F to 122˚F (-10˚C to +50˚C)

20% to 80%

Condition

Check Point

Are the camera and connected equipment turned on?

Is the iris of the lens adjusted properly?

Are cables connected correctly?

No image

0.77 lbs (350 g)

Is the monitor TV adjusted correctly?

Is the lighting too dim?

External dimensions

Automatic electronic shutter

2.48(W) x 1.97(H) x 4.57(D) inches (63(W) x 50(H) x 116(D) mm)

ON (1/60 s to 1/100000 s) /OFF (1/60 s)

Unnatural color

- 12 -

- 13 -

IK-6410A/IK-6420A

13. EXTERIOR VIEW