Nokia 6126 and Nokia 6133b
User Guide
Issue 1
xxxxxxx
1
This device complies with Directive 2002/95/EC on the restriction of the use of certain
hazardous substances in electrical and electronic equipment.
Under no circumstances shall Nokia be responsible for any loss of data or income or any
special, incidental, consequential or indirect damages howsoever caused.
The contents of this document are provided "as is". Except as required by applicable law, no
warranties of any kind, either express or implied, including, but not limited to, the implied
warranties of merchantability and fitness for a particular purpose, are made in relation to the
accuracy, reliability or contents of this document. Nokia reserves the right to revise this
document or withdraw it at any time without prior notice.
EXPORT CONTROLS
This device may contain commodities, technology, or software subject to export laws and
regulations from the U.S. and other countries. Diversion contrary to law is prohibited.
FCC/INDUSTRY CANADA NOTICE
Your device may cause TV or radio interference (for example, when using a telephone in close
proximity to receiving equipment). The FCC or Industry Canada can require you to stop using
your telephone if such interference cannot be eliminated. If you require assistance, contact
your local service facility. This device complies with part 15 of the FCC rules. Operation is
subject to the following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including interference that may
cause undesired operation. Any changes or modifications not expressly approved by Nokia
could void the user's authority to operate this equipment.
The availability of particular products may vary by region. Please check with the Nokia dealer
nearest to you.
3
Contents
For your safety..........................................7 Multimedia messaging service ........ 29
Write and send a message ............ 30
General information ........................... 10
Overview of functions........................ 10
Access codes......................................... 10
Security code..................................... 10
PIN codes............................................ 10
PUK codes........................................... 11
Restricting password....................... 11
Configuration settings service......... 11
Download content............................... 11
Install SIM card and battery............. 13
Insert a microSD card......................... 14
Remove the microSD card................. 14
Charge the battery.............................. 14
Open and close the phone ................ 15
Switch the phone on and off........... 15
Set the time and date..................... 16
Antenna.................................................. 16
Phone strap ........................................... 16
Keys and parts...................................... 17
Connector flap.................................. 17
Standby mode....................................... 18
Main display...................................... 18
Active standby .................................. 18
Shortcuts in the standby mode.... 19
Indicators............................................ 19
Keypad lock (keyguard)...................... 20
Functions without a SIM card......... 20
Make a call............................................ 22
1-touch dialing................................. 22
Enhanced voice dialing................... 22
Answer or decline a call .................... 23
Call waiting........................................ 24
Options during a call.......................... 24
Predictive text input........................... 25
Traditional text input ......................... 26
Text messages....................................... 28
Write and send a message ............ 28
Read and reply to a message........ 29
SIM messages....................................... 29
Cancel message sending................ 31
Read and reply to a message........ 31
Memory full........................................... 32
Folders .................................................... 32
Flash messages..................................... 33
Write a flash message.................... 33
Receive a flash message ................ 33
Nokia Xpress audio messaging........ 33
Create an audio message............... 33
Receive an audio message............. 34
Voice messages.................................... 34
Info messages....................................... 34
Service commands .............................. 34
Delete messages .................................. 34
Message settings................................. 35
General settings ............................... 35
Text messages................................... 35
Multimedia messages..................... 36
Search for a contact........................... 37
Save names and phone numbers .... 37
Save details........................................... 37
Copy or move contacts...................... 38
Edit contact details............................. 38
Synchronize all..................................... 38
Delete contacts.................................... 38
Business cards...................................... 38
Settings .................................................. 39
Groups .................................................... 39
1-touch dials ........................................ 39
Info, service, and my numbers......... 39
Location information.......................... 41
Profiles.................................................... 42
Themes.................................................... 42
Tones....................................................... 42
Main display.......................................... 43
Standby mode settings................... 43
Screen saver ...................................... 43
Mini display........................................... 44
4
Time and date ...................................... 44
Stop the alarm ................................. 64
My shortcuts ........................................ 44 Calendar ................................................ 64
Left selection key............................. 44
Right selection key.......................... 44
Make a calendar note .................... 65
Note alarm ........................................ 65
Shortcut bar...................................... 45 To-do list............................................... 65
Scroll keys.......................................... 45 Notes ...................................................... 65
Voice commands.............................. 45 Calculator.............................................. 66
Connectivity ......................................... 45 Countdown timer................................ 66
Bluetooth wireless technology.... 46 Stopwatch............................................. 66
Packet data........................................ 47 Launch a game .................................... 68
Data transfer..................................... 48 Launch an application....................... 68
USB data cable................................. 49 Download an application.................. 68
Call.......................................................... 49 Presenter ............................................... 69
Phone...................................................... 51 Set up browsing .................................. 72
Enhancements...................................... 51 Connect to a service .......................... 72
Configuration....................................... 52 Browse pages....................................... 73
Security.................................................. 53
Phone software updates ................... 53
Settings .............................................. 54
Browse with phone keys................ 73
Options while browsing................. 73
Direct calling .................................... 73
Request a software update........... 54 Bookmarks............................................. 74
Install a software update.............. 54 Receive a bookmark........................ 74
Restore factory settings.................... 54 Appearance settings........................... 74
Print images.......................................... 57 Security settings.................................. 75
Memory card........................................ 57
Format the memory card............... 58
Cookies ............................................... 75
Scripts over secure connection ... 75
Lock the memory card.................... 58 Download settings.............................. 75
Check memory consumption........ 58 Service inbox........................................ 75
Camera................................................... 59
Service inbox settings.................... 76
Take a photo ..................................... 59 Cache memory..................................... 76
Record a video clip.......................... 60 Browser security.................................. 76
Camera options................................ 60
Media player......................................... 60
Configuration for streaming ....... 60
Security module............................... 76
Certificates........................................ 77
Digital signature.............................. 77
Music player......................................... 60 Nokia PC Suite..................................... 79
Play music tracks............................. 61 EGPRS, HSCSD, and CSD................... 79
Music player settings ..................... 61 Data communication applications. 79
Voice recorder...................................... 62 Charging and discharging ................ 80
Record sound.................................... 62 Nokia battery authentication.......... 81
Equalizer................................................ 62 Care and maintenance ...................... 83
Stereo widening .................................. 63 Additional safety information......... 84
Index....................................................... 89
Alarm clock........................................... 64
5
F o r y o u r s a f e t y
For your safety
Read these simple guidelines. Not following them may be dangerous or illegal.
Read the complete user guide for further information.
SWITCH ON SAFELY
Do not switch the phone on when wireless phone use is prohibited or
when it may cause interference or danger.
ROAD SAFETY COMES FIRST
Obey all local laws. Always keep your hands free to operate the
vehicle while driving. Your first consideration while driving should be
road safety.
INTERFERENCE
All wireless phones may be susceptible to interference, which could
affect performance.
SWITCH OFF IN HOSPITALS
Follow any restrictions. Switch the phone off near medical
equipment.
SWITCH OFF IN AIRCRAFT
Follow any restrictions. Wireless devices can cause interference in
aircraft.
SWITCH OFF WHEN REFUELING
Do not use the phone at a refuelling point. Do not use near fuel or
chemicals.
SWITCH OFF NEAR BLASTING
Follow any restrictions. Do not use the phone where blasting is in
progress.
USE SENSIBLY
Use only in the normal position as explained in the product
documentation. Do not touch the antenna unnecessarily.
QUALIFIED SERVICE
Only qualified personnel may install or repair this product.
ENHANCEMENTS AND BATTERIES
Use only approved enhancements and batteries. Do not connect
incompatible products.
6
F o r y o u r s a f e t y
WATER-RESISTANCE
Your phone is not water-resistant. Keep it dry.
BACK-UP COPIES
Remember to make back-up copies or keep a written record of all
important information stored in your phone.
CONNECTING TO OTHER DEVICES
When connecting to any other device, read its user guide for detailed
safety instructions. Do not connect incompatible products.
EMERGENCY CALLS
Ensure the phone is switched on and in service. Press the end key as
many times as needed to clear the display and return to the start
screen. Enter the emergency number, then press the call key. Give
your location. Do not end the call until given permission to do so.
■ About your device
The wireless device described in this guide is approved for use on the GSM 850,
900, 1800, and 1900 networks. Contact your service provider for more
information about networks.
When using the features in this device, obey all laws and respect the privacy and
legitimate rights of others.
When taking and using images or video clips, obey all laws and respect local
customs as well as privacy and legitimate rights of others.
Warning: To use any features in this device, other than the alarm clock,
the device must be switched on. Do not switch the device on when
wireless device use may cause interference or danger.
■ Network services
To use the phone you must have service from a wireless service provider. Many of
the features in this device depend on features in the wireless network to
function. These network services may not be available on all networks or you may
have to make specific arrangements with your service provider before you can
utilize network services. Your service provider may need to give you additional
instructions for their use and explain what charges will apply. Some networks
may have limitations that affect how you can use network services. For instance,
some networks may not support all language-dependent characters and services.
Your service provider may have requested that certain features be disabled or not
activated in your device. If so, they will not appear on your device menu. Your
7
F o r y o u r s a f e t y
device may also have been specially configured for your network provider. This
configuration may include changes in menu names, menu order and icons.
Contact your service provider for more information.
This device supports WAP 2.0 protocols (HTTP and SSL) that run on TCP/IP
protocols. Some features of this device, such as multimedia messaging (MMS),
browsing, remote synchronization, and content downloading using the browser
or MMS, require network support for these technologies.
■ Shared memory
The following features in this device may share memory: gallery, contacts, text
messages, multimedia messages, instant messaging, calendar, to-do notes,
JavaTM games and applications, and note application. Use of one or more of these
features may reduce the memory available for the remaining features sharing
memory. For example, saving many Java applications may use all of the available
memory. Your device may display a message that the memory is full when you try
to use a shared memory feature. In this case, delete some of the information or
entries stored in the shared memory features before continuing. Some of the
features, such as text messages, may have a certain amount of memory specially
allotted to them in addition to the memory shared with other features.
■ Enhancements
A few practical rules about accessories and enhancements
•
•
Keep all accessories and enhancements out of the reach of small children.
When you disconnect the power cord of any accessory or enhancement, grasp
and pull the plug, not the cord.
•
•
Check regularly that enhancements installed in a vehicle are mounted and
are operating properly.
Installation of any complex car enhancements must be made by qualified
personnel only.
8
G e n e r a l i n f o r m a t i o n
General information
■ Overview of functions
Your phone provides many functions that are practical for daily use, such as a
text and multimedia messaging, a calendar, a clock, an alarm clock, a music
player, and a built-in camera. Your phone also supports the following functions:
•
A microSD memory card to extend the memory capacity of the phone. See
"Memory card," p. 56.
•
•
•
Active standby. See "Active standby," p. 17.
Audio messaging. See "Nokia Xpress audio messaging," p. 32.
Enhanced voice dialing. See "Enhanced voice dialing," p. 21 and "Voice
commands," p. 44.
•
Java 2 Platform, Micro Edition (J2METM). See "Applications," p. 67.
■ Access codes
Security code
The security code (5 to 10 digits) helps to protect your phone against
unauthorized use. The preset code is 12345. To change the code, and to set the
phone to request the code, see "Security," p. 52.
PIN codes
The personal identification number (PIN) code and the universal personal
identification number (UPIN) code (4 to 8 digits) help to protect your SIM card
against unauthorized use. See "Security," p. 52.
The PIN2 code (4 to 8 digits) may be supplied with the SIM card and is required
for some functions.
The module PIN is required to access the information in the security module. See
"Security module," p. 75.
The signing PIN is required for the digital signature. See "Digital signature," p. 76.
9
G e n e r a l i n f o r m a t i o n
PUK codes
The personal unblocking key (PUK) code and the universal personal unblocking
key (UPUK) code (8 digits) is required to change a blocked PIN code and UPIN
code, respectively. The PUK2 code (8 digits) is required to change a blocked PIN2
code. If the codes are not supplied with the SIM card, contact your local service
provider for the codes.
Restricting password
The restricting password (4 digits) is required when using Call restrictions. See
"Security," p. 52.
■ Configuration settings service
To use some of the network services, such as mobile Internet services, MMS,
Nokia Xpress audio messaging, or remote Internet server synchronization, your
phone needs the correct configuration settings. You may be able to receive the
settings directly as a configuration message. After receiving the settings you
must save them on your phone. The service provider may provide a PIN that is
needed to save the settings. For more information on availability, contact your
network operator, service provider, nearest authorized Nokia dealer, or visit the
support area on the Nokia Web site.
When you receive the settings as a configuration message, and the settings are
not automatically saved and activated, Configuration settings received is
displayed.
To save the settings, select Show > Save. If the phone requests Enter settings'
PIN:, enter the PIN code for the settings, and select OK. To receive the PIN code,
contact the service provider that supplies the settings. If no settings are saved,
these settings are saved and set as default configuration settings. Otherwise, the
phone asks Activate saved configuration settings?.
To discard the received settings, select Exit or Show > Discard.
■ Download content
You may be able to download new content (for example, themes) to the phone
(network service). Select the download function (for example, in Gallery). To
access the download function, see the respective menu descriptions.
You may also be able to download updates of phone software (network service).
See "Phone," p. 50, Phone updates.
10
G e n e r a l i n f o r m a t i o n
For the availability of different services, pricing, and tariffs, contact your service
provider.
Important: Use only services that you trust and that offer adequate
security and protection against harmful software.
11
G e t s t a r t e d
1. Get started
■ Install SIM card and battery
Always switch the device off and disconnect the charger before removing the
battery.
Keep all SIM cards out of the reach of small children.
For availability and information on using SIM card services, contact your SIM
card vendor. This may be the service provider, network operator, or other vendor.
This device is intended for use with BL-4C battery. Always use original Nokia
batteries. See "Nokia battery authentication," p. 80.
The SIM card and its contacts are damaged by scratches or bending, so be careful
when handling, inserting, or removing the card.
To remove the back cover
of the phone, press
sightly (1), and slide the
cover off (2). Remove the
battery as shown (3).
Open the SIM card holder
(4), and insert the SIM
card properly into the
holder (5).
Closethe SIM card holder
(6).
Replace the battery (7).
Slide the back cover into
its place (8, 9).
12
G e t s t a r t e d
■ Insert a microSD card
Keep all microSD memory cards out of the reach of small children.
Use only microSD cards approved by Nokia for use with this device. Nokia utilizes
the approved industry standards for memory cards, but not all other brands may
function correctly or be fully compatible with this device.
Use only compatible microSD cards with this device. Other memory cards, such as
reduced-size multimedia cards, do not fit in the microSD card slot and are not
compatible with this device. Using an incompatible memory card may damage
the memory card as well as the device, and data stored on the incompatible card
may be corrupted.
1. Remove the back cover of the phone.
2. Insert the card into the microSD card slot
with the gold-colored contact surface
facing down, and press it until it locks into
place.
3. Close the back cover of the phone.
■ Remove the microSD card
Important: Do not remove the microSD card in the middle of an
operation when the card is being accessed. Removing the card in the
middle of an operation may damage the memory card as well as the
device, and data stored on the card may be corrupted.
You can remove or replace the microSD card during phone operation without
switching the phone off.
1. Make sure that no application is accessing the microSD memory card.
2. Remove the back cover of the phone.
3. Press the microSD card slightly in to release the lock.
4. Remove the microSD card from the slot.
■ Charge the battery
Check the model number of any charger before use with this device. This device is
intended for use when supplied with power from an AC-3 or AC-4 charger.
13
G e t s t a r t e d
Warning: Use only batteries, chargers, and enhancements approved by
Nokia for use with this particular model. The use of any other types may
invalidate any approval or warranty, and may be dangerous.
For availability of approved enhancements, please check with your dealer. When
you disconnect the power cord of any enhancement, grasp and pull the plug, not
the cord.
1. Connect the charger to a wall socket.
2. Connect the plug from the charger to the jack on the
bottom of your phone.
If the battery is completely discharged, it may take a few
minutes before the charging indicator appears on the
display or before any calls can be made.
The charging time depends on the charger used. Charging a BL-4C battery with
the AC-3 charger takes approximately 2 hours and 20 minutes while the phone is
in the standby mode.
■ Open and close the phone
To open the phone, press the fold
release button (1). The fold opens
automatically (2).
To close the phone, turn the fold
manually in its closed position.
To switch off a tone that sounds
when you open and close the phone,
see "Tones," p. 41.
■ Switch the phone on and off
Warning: Do not switch the phone on when wireless phone use is
prohibited or when it may cause interference or danger.
To switch the phone on or off, press and hold the power key. See "Keys and parts,"
p. 16.
If the phone prompts for a PIN or a UPIN code, enter the code (displayed as ****),
and select OK.
14
G e t s t a r t e d
Set the time and date
Enter the local time, select the time zone of your location in terms of the time
difference with respect to Greenwich Mean Time (GMT), and enter the date. See
"Time and date," p. 43.
■ Antenna
Your device has an internal antenna.
Note: As with any other radio
transmitting device, do not touch
the antenna unnecessarily when the
device is switched on. Contact with
the antenna affects call quality and
may cause the device to operate at a
higher power level than otherwise
needed. Avoiding contact with the
antenna area when operating the
device optimizes the antenna
performance and the battery life.
■ Phone strap
Thread the strap through the eyelet of the phone
as shown in the picture, and tighten it.
15
Y o u r p h o n e
2. Your phone
■ Keys and parts
Earpiece (1)
Main display (2)
Left and right selection keys (3)
Middle selection key (4)
Call key (5)
Keypad (6)
Fold release button (7)
4-way scroll key (8)
End key (9)
Loudspeaker (10)
Phone strap eyelet (11)
Pop-PortTM connector flap (12)
Charger connector (13)
Camera lens (14)
Volume up and down key,
and zoom in and outkey (15)
Mini display (16)
Camera key (17)
Power key (18)
Connector flap
To connect enhancements, open the Pop-PortTM
connector flap.
16
Y o u r p h o n e
■ Standby mode
When the phone is ready for use, and you have not entered any characters, the
phone is in the standby mode.
Main display
Signal strength of the cellular network (1)
Battery charge status (2)
Indicators (3)
Network name or the operator logo (4)
Clock (5)
Main screen (6)
Left selection key — Go to or a shortcut to another
function (7). See "Left selection key," p. 43.
Middle selection key — Menu (8)
Right selection key — Names or a shortcut to another function (9). See "Right
selection key," p. 43. Operator variants may have an operator-specific name to
access an operator-specific Web site.
Active standby
In the active standby mode, you can use the main display for fast access to
frequently used applications. To switch on the mode, select Menu > Settings >
Main display > Standby mode settings > Active standby > My active standby.
In the active standby mode, scroll to the feature on the navigation bar in the
main display. To start the feature, select Select; or to display the information,
select View. Left and right arrows at the beginning and end of a line indicate that
further information is available by scrolling left or right. To end the active
standby mode, select Exit.
To organize and change the active standby mode, activate the mode, and select
Options > Active standby > My active standby > Options and the following
options:
Personalize — Assign or change phone features in the standby mode.
Organize — Move the position of features in the standby mode.
17
Y o u r p h o n e
Enabling active standby — Select keys to activate the standby mode. To change
the settings, see "Standby mode settings," p. 42.
To switch off the active standby mode select Options > Active standby > Off; or
select Menu > Settings > Main display > Standby mode settings >Active
standby > Off.
Shortcuts in the standby mode
•
To access the list of dialed numbers, press the call key once. Scroll to the
number or name that you want. To call the number, press the call key.
•
•
•
•
•
•
•
To open the Web browser, press and hold 0.
To call your voice mailbox, press and hold 1.
Use the scroll key as a shortcut. See "My shortcuts," p. 43.
Press the camera key to start the camera (still photo).
Press and hold the camera key to start a video recording.
In camera mode, press the volume keys to zoom in or out.
Press a volume key to mute the ringing tone of an incoming call when the
phone is closed.
•
Press the power key to access the profiles menu on the main display.
Indicators
You have unread messages in the Inbox folder.
You have unsent, canceled, or failed messages in the Outbox folder.
The phone logged a missed call.
,
Your phone is connected to the instant messaging service, and the
availability status is online or offline.
You received one or several instant messages, and you are connected to
the instant messaging service.
The keypad is locked.
The phone does not ring for an incoming call or text message.
The alarm clock is set to On.
18
Y o u r p h o n e
The countdown timer is running.
The stopwatch is running in the background.
The phone is registered to the GPRS or EGPRS network.
A GPRS or EGPRS connection is established.
,
,
,
The GPRS or EGPRS connection is suspended (on hold), for example, if
there is an incoming or outgoing call during an EGPRS dial-up
connection.
A Bluetooth connection is active.
If you have two phone lines, the second phone line is selected.
All incoming calls are forwarded to another number.
The loudspeakers are activated, or the music stand is connected to the
phone.
Calls are limited to a closed user group.
The timed profile is selected.
,
,
, or
A headset, hands-free, loopset, or music stand
enhancement is connected to the phone.
■ Keypad lock (keyguard)
To prevent accidental key presses, select Menu, and press within 3.5 seconds to
*
lock the keypad.
To unlock the keypad, select Unlock, and press within 1.5 seconds. If the
*
Security keyguard is set On, enter the security code if requested.
To answer a call when the keyguard is on, press the call key. When you end or
decline the call, the keypad automatically locks.
For Security keyguard, see "Phone," p. 50.
When the keyguard is on, calls still may be possible to the official emergency
number programmed into your device.
■ Functions without a SIM card
Several functions of your phone may be used without installing a SIM card (for
example, the data transfer with a compatible PC or another compatible device).
19
Y o u r p h o n e
Note that when you use the phone without a SIM card, some functions appear
dimmed in the menus and cannot be used. Synchronizing with a remote Internet
server is not possible without a SIM card.
For an emergency call, some networks may require that a valid SIM card is
properly inserted in the device.
20
C a l l f u n c t i o n s
3. Call functions
■ Make a call
1. Enter the phone number, including the area code.
For international calls, press twice for the international prefix (the +
*
character replaces the international access code); enter the country code, the
area code without the leading 0, if necessary, and the phone number.
2. To call the number, press the call key.
3. To end the call or to cancel the call attempt, press the end key, or close the
phone.
To search for a name or phone number that you have saved in Contacts, see
"Search for a contact," p. 36. Press the call key to call the number.
To access the list of dialed numbers, press the call key once in the standby mode.
To call the number, select a number or name, and press the call key.
1-touch dialing
Assign a phone number to one of the 1-touch-dialing keys, 2 to 9. See "1-touch
dials," p. 38. Call the number in either of the following ways:
•
•
Press a 1-touch-dialing key, then the call key.
If 1-touch dialing is set to On, press and hold a 1-touch-dialing key until the
call begins. See 1-touch dialing in "Call," p. 48.
Enhanced voice dialing
To make a phone call, say the name that is saved in the contact list of the phone.
A voice command is added automatically to all entries in the contact list of the
phone.
If an application is sending or receiving data using a packet data connection, end
the application before you use voice dialing.
Voice commands are language-dependent. To set the language, see Voice
playback language in "Phone," p. 50.
21
C a l l f u n c t i o n s
Note: Using voice tags may be difficult in a noisy environment or during
an emergency, so you should not rely solely upon voice dialing in all
circumstances.
1. In the standby mode, press and hold the right selection key, or press and hold
the volume down key. A short tone sounds, and Speak now is displayed.
If you are using a compatible headset with the headset key, press and hold
the headset key to start the voice dialing.
2. Say the voice command clearly. If voice recognition is successful, a list with
matches is displayed. The phone plays the voice command of the match on
the top of the list. After about 1.5 seconds, the phone dials the number; or if
the result is not the correct one, scroll to another entry, and select to dial the
entry.
Using voice commands to carry out a selected phone function is similar to
voice dialing. See Voice commands in "My shortcuts," p. 43.
■ Answer or decline a call
To answer an incoming call, press the call key, or open the phone. To end the call,
press the end key, or close the phone.
To decline an incoming call if the phone is open, press the end key. To decline an
incoming call when the phone is closed, press and hold a volume key.
To mute the ringing tone, press a volume key when the phone is closed, or select
Silence when the phone is open.
If the Forward if busy function is activated to forward the calls (for example, to
your voice mailbox), declining an incoming call also forwards the call. See "Call,"
p. 48.
If a compatible headset (supplied with the headset key) is connected to the
phone, to answer and end a call, press the headset key.
22
C a l l f u n c t i o n s
Call waiting
To answer the waiting call during an active call, press the call key. The first call is
put on hold. To end the active call, press the end key.
To activate the Call waiting function, see "Call," p. 48.
■ Options during a call
Many of the options that you can use during a call are network services. For
availability, contact your service provider.
During a call, select Options and from the following options:
Mute or Unmute, Contacts, Menu, Lock keypad, Record, Loudspeaker or Handset.
Network services options are Answer or Decline, Hold or Unhold, New call, Add to
conference, End call, End all calls, and the following:
Touch tones — to send tone strings
Swap — to switch between the active call and the call on hold
Transfer calls — to connect a call on hold to an active call and disconnect yourself
Conference — to make a conference call that allows up to five persons to take
part in a conference call
Private call —to discuss privately in a conference call
To change the volume during a call, press the volume up key or the volume down
key.
Warning: Do not hold the device near your ear when the loudspeaker is
in use, because the volume may be extremely loud.
23
W r i t e t e x t
4. Write text
To enter text (for example, when writing messages), use traditional or predictive
text input. When you write text, text input indicators appear at the top of the
display.
indicates traditional text input.
indicates predictive text
input. Predictive text input allows you to write text quickly using the phone
keypad and a built-in dictionary. You can enter a letter with a single keypress.
indicates predictive text input with Word suggestions. The phone predicts
and completes the word before you enter all the characters.
,
, or
appears next to the text input indicator, indicating the
character case. To change the character case, press #.
indicates number mode. To change from the letter to number mode, press
and hold #, and select Number mode.
To set the writing language while writing text, select Options > Writing
language.
■ Predictive text input
To set predictive text input on, select Options > Prediction on.
To quickly set predictive text input on or off when writing text, press # twice, or
select and hold Options.
1. To start writing a word, use keys, 2 to 9. Press each key only once for one
letter. The entered letters are displayed underlined.
To insert a special character, press and hold , or select Options > Insert
*
symbol. Scroll to a character, and select Insert.
To write compounds words, enter the first part of the word; to confirm it,
press the right scroll key. Write the next part of the word, and confirm the
word.
To enter a full stop, press 1.
2. When you finish writing the word and it is correct, to confirm it, press 0 to
add space.
If the word is not correct, press repeatedly, or select Options > Matches.
*
When the word that you want appears, select the word and press the scroll
key.
24
W r i t e t e x t
If the ? character is displayed after the word, the word you intended to write
is not in the dictionary. To add the word to the dictionary, select Spell.
Complete the word (traditional text input is used), and select Save.
■ Traditional text input
To set traditional text input on, select Options > Prediction off.
Press a number key, 1 to 9, repeatedly until the desired character appears. Not all
characters available under a number key are printed on the key. The characters
available depend on the selected writing language.
If the next letter you want is located on the same key as the present one, wait
until the cursor appears, or briefly press any of the scroll keys, and enter the
letter.
The most common punctuation marks and special characters are available under
the 1 key. For more characters, press
.
*
25
M e n u s
5. Menus
The phone offers you an extensive range of functions, which are grouped into
menus.
1. To access the menu, select Menu.
To change the menu view, select Options > Main menu view > List, Grid, Grid
with labels, or Tab.
To rearrange the menu, scroll to the menu you want to move, and select
Options > Organize > Move. Scroll to where you want to move the menu, and
select OK. To save the change, select Done > Yes.
2. Scroll through the menu, and select an option (for example, Settings).
3. If the selected menu contains further submenus, select the one that you want
(for example, Call).
4. If the selected menu contains further submenus, repeat step 3.
5. Select the setting of your choice.
6. To return to the previous menu level, select Back. To exit the menu, select
Exit.
26
M e s s a g i n g
6. Messaging
You can read, write, send, and save text, multimedia, audio, and flash messages.
All messages are organized into folders.
■ Text messages
Use the short message service (SMS) to send and receive text messages, and
receive messages that can contain pictures (network service).
Before you can send any text or SMS e-mail message, you must save your
message center number. See "Message settings," p. 34.
To check SMS e-mail service availability and to subscribe to the service, contact
your service provider. To save an e-mail address in Contacts, see "Save details," p.
36.
Your device supports the sending of text messages beyond the character limit for
a single message. Longer messages will be sent as a series of two or more
messages. Your service provider may charge accordingly. Characters that use
accents or other marks, and characters from some language options like Chinese,
take up more space, limiting the number of characters that can be sent in a single
message.
The message length indicator at the top of the display shows the total number of
characters left and the number of messages needed for sending. For example,
673/2 means that there are 673 characters left and that the message will be sent
as a series of two messages.
Write and send a message
1. Select Menu > Messaging > Create message > Text message.
2. Enter the recipient’s phone number or e-mail address in the To: field. To
retrieve a phone number or e-mail address from Contacts, select Add >
Contact. To send the message to multiple recipients, add the desired contacts
one by one. To send the message to persons in a group, select Contact group
and the desired group. To retrieve the contacts to which you recently sent
messages, select Add > Recently used. To retrieve contacts from previously
incoming calls, select Add > Open Log.
3. For a SMS e-mail, enter a subject in the Subject: field.
27
M e s s a g i n g
4. Write your message in the Message: field. See "Write text," p. 24. To insert a
template into the message, select Options > Use template. To see how the
message will look to the recipient, select Options > Preview.
5. To send the message, select Send. See "When you finish writing your
message, to send the message, select Send. The phone saves the message in
the Outbox folder, and the sending starts. If you select Save sent messages >
Yes, the sent message is saved in the Sent items folder. See "General
settings," p. 34.," p. 30.
Read and reply to a message
When you receive a message, 1 message received or the number of new messages
with N messages received are displayed.
1. To view a new message, select Show. To view it later, select Exit.
To read the message later, select Menu > Messaging > Inbox. If more than
one message is received, select the message you want to read.
is
displayed if you have unread messages in Inbox.
2. To view the list of available options while reading a message, select Options.
3. To reply to a message, select Reply > Text message, Multimedia, Flash
message, or Audio message.
To send a text message to an e-mail address, enter the e-mail address in the
To: field.
Scroll down, and write your message in the Message: field. See "Write text," p.
24.
If you want to change the message type for your reply message, select
Options > Change message type.
4. To send the message, select Send. See "When you finish writing your
message, to send the message, select Send. The phone saves the message in
the Outbox folder, and the sending starts. If you select Save sent messages >
Yes, the sent message is saved in the Sent items folder. See "General
settings," p. 34.," p. 30.
■ SIM messages
SIM messages are text messages that are saved to your SIM card. You can copy or
move those messages to the phone memory, but not vice versa. Received
messages are saved to the phone memory.
28
M e s s a g i n g
To read SIM messages, select Menu > Messaging > Options > SIM messages.
■ Multimedia messaging service
Note: Only devices that have compatible features can receive and
display multimedia messages. The appearance of a message may vary
depending on the receiving device.
To check availability and to subscribe to the multimedia messaging service
(MMS), contact your service provider. See "Multimedia messages," p. 35.
A multimedia message can contain text, sound, images, video clips, a business
card, and a calendar note. If the message is too large, the phone may not be able
to receive it. Some networks allow text messages that include an Internet address
where you can view the multimedia message.
You cannot receive multimedia messages during a call or an active browsing
session over GSM data. Because delivery of multimedia messages can fail for
various reasons, do not rely solely upon them for essential communications.
Write and send a message
The wireless network may limit the size of MMS messages. If the inserted image
exceeds this limit, the device may make it smaller so that it can be sent by MMS.
1. Select Menu > Messaging > Create message > Multimedia.
2. Enter your message.
Your phone supports multimedia messages that contain several pages
(slides). A message can contain a calendar note and a business card as
attachments. A slide can contain text, one image, and one sound clip; or text
and a video clip. To insert a slide in the message, select New; or select
Options > Insert > Slide.
To insert a file in the message, select Insert; or select Options > Insert.
3. To view the message before sending it, select Options > Preview.
4. To send the message, select Send.
5. Enter the recipient’s phone number in the To: field. To retrieve a phone
number from Contacts, select Add > Contact. To send the message to
multiple recipients, add the desired contacts one by one. To send the message
to persons in a group, select Contact group and the desired group. To retrieve
29
M e s s a g i n g
the contacts to which you recently sent messages, select Add > Recently
used.
Copyright protections may prevent some images, music (including ringing tones),
and other content from being copied, modified, transferred, or forwarded.
When you finish writing your message, to send the message, select Send. The
phone saves the message in the Outbox folder, and the sending starts. If you
select Save sent messages > Yes, the sent message is saved in the Sent items
folder. See "General settings," p. 34.
Note: When the phone is sending the message, the animated
is
displayed. This is an indication that the message has been sent by your
device to the message center number programmed into your device.
This is not an indication that the message has been received at the
intended destination. For more details about messaging services, check
with your service provider.
It takes more time to send a multimedia message than to send a text message.
While the message is being sent, you can use other functions on the phone. If an
interruption occurs while the message is being sent, the phone tries to resend the
message a few times. If these attempts fail, the message remains in the Outbox
folder. You can try to resend it later.
Cancel message sending
To cancel the sending of the messages in the Outbox folder, scroll to the desired
message, and select Options > Cancel sending.
Read and reply to a message
Important: Exercise caution when opening messages. Multimedia
message objects may contain malicious software or otherwise be
harmful to your device or PC.
When you receive a new multimedia message, Multimedia message received or
the number of new messages with N messages received is displayed.
1. To read the message, select Show. To view it later, select Exit.
To read the message later, select Menu > Messaging > Inbox. Scroll to the
message that you want to view, and select it.
is displayed if you have
unread messages in Inbox.
30
M e s s a g i n g
2. To view the whole message if the received message contains a presentation,
select Play.
3. To view the files in the presentation or the attachments, select Options >
Objects or Attachments.
4. To reply to the message, select Options > Reply > Text message, Multimedia,
Flash message, or Audio message. Write the reply message.
If you want to change the message type for your reply message, select
Options > Change message type. The new message type may not support all
the content that you have added.
5. To send the message, select Send. See "Write and send a message," p. 29.
■ Memory full
When you receive a message, and the memory for the messages is full, Memory
full. Unable to receive messages. is displayed. To first delete old messages, select
OK > Yes and the folder. Scroll to the desired message, and select Delete. If more
messages are to be deleted, select Mark. Mark all the messages you want to
delete, and select Options > Delete marked.
■ Folders
The phone saves received messages in the Inbox folder.
Messages that have not yet been sent are saved in the Outbox folder.
To set the phone to save the sent messages in the Sent items folder, see Save sent
messages in "General settings," p. 34.
To save the message that you write and want to send later in the Drafts folder,
select Options > Save message > Drafts
You can move your messages to the Saved items folder. To organize your Saved
items subfolders, select Menu > Messaging > Saved items. To add a folder, select
Options > Add folder. To delete or rename a folder, scroll to the desired folder,
and select Options > Delete folder or Rename folder.
Your phone has templates. To create a new template, save a message as a
template. To access the template list, select Menu > Messaging > Saved items >
Templates.
31
M e s s a g i n g
■ Flash messages
Flash messages are text messages that are instantly displayed upon reception.
Flash messages are not automatically saved.
Write a flash message
Select Menu > Messaging > Create message > Flash message. Enter the
recipient’s phone number in the To: field. Scroll down, and write your message in
the Message: field. The maximum length of a flash message is 70 characters. To
insert a blinking text into the message, select Options > Insert blink character to
set a marker. The text behind the marker blinks until a second marker is inserted.
Receive a flash message
A received flash message is indicated with Message: and a few words from the
beginning of the message. To read the message, select Read. To extract phone
numbers, e-mail addresses, and Web site addresses from the current message,
select Options > Use detail. To save the message, select Save and the folder in
which you want to save it.
■ Nokia Xpress audio messaging
You can use the multimedia message service to create and send a audio message
in a convenient way. MMS must be activated before you can use audio messages.
Create an audio message
1. Select Menu > Messaging > Create message > Audio message. The recorder
opens. To use the recorder, see "Voice recorder," p. 61.
2. Speak your message.
3. Enter the recipient’s phone number in the To: field. To retrieve a phone
number from Contacts, select Add > Contact. To send the message to
multiple recipients, add the desired contacts one by one. To send the message
to persons in a group, select Contact group and the desired group. To retrieve
the contacts to which you recently sent messages, select Add > Recently
used.
4. To send the message, select Send.
32
M e s s a g i n g
Receive an audio message
When your phone receives an audio message, 1 audio message received is
displayed. To open the message, select Play; or if more than one message is
received, select Show > Play. To listen to the message later, select Exit. To see the
available options, select Options.
■ Voice messages
The voice mailbox is a network service, and you may need to subscribe to it. For
more information and for your voice mailbox number, contact your service
provider.
To call your voice mailbox, select Menu > Messaging > Voice messages > Listen
to voice messages. To enter, search for, or edit your voice mailbox number, select
Voice mailbox number.
If supported by the network,
indicates new voice messages. To call your
voice mailbox number, select Listen.
■ Info messages
With Info messages (network service), you can receive messages on various topics
from your service provider. To check availability, topics, and the relevant topic
numbers, contact your service provider.
■ Service commands
Select Menu > Messaging > Service commands. Write and send service requests
(also known as USSD commands), such as activation commands for network
services, to your service provider.
■ Delete messages
To delete messages, select Menu > Messaging > Delete messages > By message
to delete single messages, By folder to delete all messages from a folder, or All
messages. If a folder contains unread messages, the phone prompts whether you
want to delete them also.
33
M e s s a g i n g
■ Message settings
General settings
General settings are common for text and multimedia messages.
Select Menu > Messaging > Message settings > General settings and from the
following options:
Save sent messages > Yes — to set the phone to save the sent messages in the
Sent items folder
Overwriting in Sent items > Allowed — to set the phone to overwrite the old sent
messages with the new ones when the message memory is full. This setting is
displayed only if you set Save sent messages > Yes.
Font size — to select the font size used in messages
Graphical smileys > Yes — to set the phone to replace character-based smileys
with graphical ones
Text messages
The text message settings affect the sending, receiving, and viewing of text and
SMS e-mail messages.
Select Menu > Messaging > Message settings > Text messages and from the
following options:
Delivery reports > On — to ask the network to send delivery reports about your
messages (network service)
Message centers > Add center — to set the phone number and name of the
message center that is required for sending text messages. You receive this
number from your service provider.
Message center in use — to select the message center in use
E-mail message centers > Add center — to set the phone numbers and name of
the e-mail center for sending SMS e-mails.
E-mail center in use — to select the SMS e-mail message center in use
Message validity — to select the length of time for which the network attempts
to deliver your message
Messages sent via — to select the format of the messages to be sent: Text, Page,
or Fax (network service)
Use packet data > Yes — to set GPRS as the preferred SMS bearer
34
M e s s a g i n g
Character support > Full — to select all characters in the messages to be sent as
viewed. If you select Reduced, characters with accents and other marks may be
converted to other characters. You can preview a message before sending it, to
see how it will look to the recipient. See "Write and send a message," p. 27.
Reply via same center > Yes — to allow the recipient of your message to send you
a reply using your message center (network service)
Multimedia messages
The message settings affect the sending, receiving, and viewing of multimedia
messages.
You may receive the configuration settings for multimedia messaging as a
configuration message. See "Configuration settings service," p. 10. You can also
enter the settings manually. See "Configuration," p. 51.
Select Menu > Messaging > Message settings > Multimedia messages and from
the following options:
Delivery reports > On — to ask the network to send delivery reports about your
messages (network service)
Image size (multimedia) — to set the image size in multimedia messages. Before
sending, images will be reduced to the selected size.
Default slide timing — to define the default time between slides in multimedia
messages
Allow multimedia recept. — to receive or block the multimedia message, select
Yes or No. If you select In home network, you cannot receive multimedia
messages when outside your home network. The default setting of the MMS is
generally In home network. The availability of this menu depends on your phone.
Incoming multim. msgs. — to allow the reception of multimedia messages
automatically, manually after being prompted, or to decline the reception. This
setting is not displayed if Allow multimedia recept. is set to No.
Allow advertisements — to receive or decline advertisements. This setting is not
displayed if Allow multimedia recept. is set to No, or Incoming multim. msgs. is
set to Reject.
Configuration settings > Configuration — only the configurations that support
multimedia messaging are displayed. Select a service provider, Default, or
Personal configuration for multimedia messaging. Select Account and an MMS
account contained in the active configuration settings.
35
C o n t a c t s
7. Contacts
You can save names and phone numbers (contacts) in the phone
memory and in the SIM card memory.
The phone memory may save contacts with additional details, such as various
phone numbers and text items. You can also save an image for a limited number
of contacts.
The SIM card memory can save names with one phone number attached to them.
The contacts saved in the SIM card memory are indicated by
.
■ Search for a contact
Select Menu > Contacts > Names. Scroll through the list of contacts, or enter the
first characters of the name you are searching for.
■ Save names and phone numbers
Names and numbers are saved in the used memory. To save a name and phone
number, select Menu > Contacts > Names > Options > Add new contact. Enter
the last name, first name, the phone number; and select Save.
■ Save details
In the phone memory for contacts you can save different types of phone
numbers, and short text items per name. You can also select a tone or a video clip
for a contact.
The first number you save is automatically set as the default number, and it is
indicated with a frame around the number type indicator (for example,
).
When you select a name from contacts (for example, to make a call), the default
number is used unless you select another number.
1. Make sure that the memory in use is Phone or Phone and SIM. See
"Settings," p. 38.
2. Search for the contact to which you want to add a detail, and select Details >
Options > Add detail. Select from the available options.
36
C o n t a c t s
■ Copy or move contacts
To copy names and phone numbers from the phone contact memory to the SIM
card memory, or vice versa, select Menu > Contacts > Names > Options > Copy.
Select One by one to copy single contacts or All to copy all contacts. The SIM card
memory can save names with one phone number attached to them.
To copy or move all contacts from the phone contact memory to the SIM card
memory, or vice versa, select Menu > Contacts > Copy contacts or Move
contacts.
■ Edit contact details
Search for the contact you want to edit, and select Details. To edit a name,
number, text item, or to change the image, select Options > Edit. To change the
number type, scroll to the desired number, and select Options > Change type. To
set the selected number as the default number, select Set as default.
■ Synchronize all
Synchronize your calendar, contacts data, and notes with a remote Internet
server (network service). For details see "Synchronize from a server," p. 48.
■ Delete contacts
To delete all the contacts and the details attached to them from the phone or SIM
card memory, select Menu > Contacts > Delete all contacts > From phone
memory or From SIM card. Confirm with the security code.
To delete a contact, search for the desired contact, and select Options > Delete
contact.
To delete a number, text item, or an image attached to the contact, search for the
contact, and select Details. Scroll to the desired detail, and select Options >
Delete and from the available options. To delete an image or video clip from
contacts does not delete it from Gallery.
■ Business cards
You can send and receive a person’s contact information from a compatible
device that supports the vCard standard as a business card.
37
C o n t a c t s
To send a business card, search for the contact whose information you want to
send, and select Details > Options > Send business card > Via multimedia, Via
text message, or Via Bluetooth.
When you have received a business card, select Show > Save to save the business
card in the phone memory. To discard the business card, select Exit > Yes.
■ Settings
Select Menu > Contacts > Settings and from the following options:
Memory in use — to select the SIM card or phone memory for your contacts.
Select Phone and SIM to recall names and number from both memories. In that
case, when you save names and numbers, they are saved in the phone memory.
Contacts view — to select how the names and numbers in Contacts are displayed
Name display — to select whether the contact’s first or last name is displayed
first
Font size — to set the font size for the list of contacts
Memory status — to view the free and used memory capacity
■ Groups
Select Menu > Contacts > Groups to arrange the names and phone numbers
saved in the memory into caller groups with different ringing tones and group
images.
■ 1-touch dials
To assign a number to a 1-touch-dialing key, select Menu > Contacts > 1-touch
dialing, and scroll to the 1-touch-dialing number that you want.
Select Assign, or if a number has already been assigned to the key, select
Options > Change. Select Find and the contact you want to assign. If the 1-touch
dialing function is off, the phone asks whether you want to activate it. See also
1-touch dialing in "Call," p. 48.
To make a call using the 1-touch-dialing keys, see "1-touch dialing," p. 21.
■ Info, service, and my numbers
Select Menu > Contacts and from one of these submenus:
38
C o n t a c t s
Info numbers — to call the information numbers of your service provider if the
numbers are included on your SIM card (network service)
Service numbers — to call the service numbers of your service provider if the
numbers are included on your SIM card (network service)
My numbers — to view the phone numbers assigned to your SIM card if the
numbers are included on your SIM card
39
C a l l l o g
8. Call log
The phone logs your missed, received, and dialed calls if the network supports it
and the phone is switched on and within the network service area.
To view the information on your calls, select Menu > Log > Missed calls, Received
calls, or Dialed numbers. To view your recent missed and received calls and the
dialed numbers chronologically, select Call log. To view the contacts to whom
you most recently sent messages, select Message recipients.
To view the approximate information on your recent communications, select
Menu > Log > Call timers, Packet data counter, or Packet data timer.
To view how many text and multimedia messages you have sent and received,
select Menu > Log > Message log.
Note: The actual invoice for calls and services from your service
provider may vary, depending on network features, rounding off for
billing, taxes, and so forth.
Some timers may be reset during service or software upgrades.
■ Location information
The network may send you a location request. You can ensure that the
network will deliver location information of your phone only if you
approve it (network service). Contact your service provider to subscribe
and to agree upon the delivery of location information.
To accept or decline the location request, select Accept or Reject. If you miss the
request, the phone automatically accepts or rejects it according to what you have
agreed with your network operator or service provider. The phone displays 1
missed position request. To view the missed location request, select Show.
To view the information on the 10 most recent privacy notifications and requests
or to delete them, select Menu > Log > Positioning > Position log > Open folder
or Delete all.
40
S e t t i n g s
9. Settings
■ Profiles
Your phone has various setting groups called profiles, for which you can
customize the phone tones for different events and environments.
Select Menu > Settings > Profiles, the desired profile, and from the following
options:
Activate — to activate the selected profile
Customize — to personalize the profile. Select the setting you want to change,
and make the changes.
Timed — to set the profile to be active until a certain time up to 24 hours, and set
the end time. When the time set for the profile expires, the previous profile that
was not timed becomes active.
■ Themes
A theme contains many elements for personalizing your phone, such as
wallpaper, screen savers, color schemes, and a ringing tones.
Select Menu > Settings > Themes and from the following options:
Select theme — to set a theme in your phone. A list of folders in Gallery opens.
Open the Themes folder, and select a theme.
Theme downloads — to open a list of links to download more themes
■ Tones
You can change the tone settings of the selected active profile.
Select Menu > Settings > Tones. You can find the same settings in the Profiles
menu. See Customize in "Profiles," p. 41.
To set the phone to ring only for calls from phone numbers that belong to a
selected caller group, select Alert for. Scroll to the caller group you want or All
calls, and select Mark.
Select Options > Save to save the settings or Cancel to leave the settings
unchanged.
If you select the highest ringing tone level, the ringing tone reaches its highest
level after a few seconds.
41
S e t t i n g s
A theme may contain a tone that sounds when you open and close the phone. To
switch off the tone, change the setting in Other tones:. Please note that this
setting also switches off the warning tones.
■ Main display
Select Menu > Settings > Main display and from the available options.
Standby mode settings
Select Standby mode settings and from the following options:
Active standby — to switch the active standby mode on or off and to organize and
personalize the active standby mode. See "Active standby," p. 17.
Wallpaper — to add the background image to the display in the standby mode
Fold animation — to set your phone to display an animation when you open and
close the phone
Standby font color — to select the color for the texts on the display in the standby
mode
Navigation key icons — to display the icons of the current scroll key shortcuts in
the standby mode when active standby is off
Operator logo — to set your phone to display or hide the operator logo. The menu
is dimmed if you have not saved the operator logo. For more information on
availability of an operator logo, contact your network operator.
Cell info display > On — to display the cell identity if available from the network
Screen saver
Select Screen saver and from the following options:
On — to activate the screen saver for the main display
Screen savers > Image — to choose an image or a graphic from the Gallery
Screen savers > Slide set and a folder in Gallery — to use the images in the folder
as a slide set
Screen savers > Video clip and a video clip from Gallery — to run a video clip as
the screen saver (only on the main display)
Screen savers > Open camera — to take a new photo as the screen saver
Screen savers > Analog clock or Digital clock — to use a clock as the screen saver
Graphic downloads — to download more images for the screen saver
42
S e t t i n g s
Time-out — to set the time after which the screen saver is activated
■ Mini display
Select Menu > Settings > Mini display. You can change the settings for
Wallpaper, Screen saver, and Fold animation.
■ Time and date
To change the time, time zone, and date settings, select Menu > Settings > Time
and date > Clock, Date, or Auto-update of date/time (network service).
When traveling to a different time zone, select Menu > Settings > Time and
date > Clock > Time zone and the time zone of your location in terms of the time
difference with respect to Greenwich Mean Time (GMT) or Universal Time
Coordinated (UTC). The time and date are set according to the time zone and
enable your phone to display the correct sending time of received text or
multimedia messages. For example, GMT -5 denotes the time zone for New York
(USA), 5 hours west of Greenwich, London (UK).
■ My shortcuts
With personal shortcuts, you get quick access to often used functions of the
phone.
Left selection key
To select a function from the list for the left selection key, select Menu >
Settings > My shortcuts > Left selection key. See also "Standby mode," p. 17.
If the left selection key is Go to to activate a function, in the standby mode, select
Go to > Options and from the following options:
Select options — to add a function to the shortcut list or to remove one. Scroll to
the function, and select Mark or Unmark.
Organize — to rearrange the functions on your personal shortcut list. Scroll to the
function you want to move, and select Move. Scroll to where you want to move
the function, and select OK.
Right selection key
To select a function from the list for the right selection key, select Menu >
Settings > My shortcuts > Right selection key. See also "Standby mode," p. 17.
43
S e t t i n g s
Shortcut bar
To choose and reorder applications displayed by the shortcut bar in the active
standby mode, select Menu > Settings > My shortcuts > Shortcut bar.
Select Select links, and mark the desired application in the list or in a folder.
Select Done > Yes to confirm the selection.
Select Organize links to reorder the applications in the shortcut bar. Select an
application, Move, and move it to an other position. Select OK to confirm. Select
Done > Yes to save the shortcut sequence.
Scroll keys
To select shortcut functions for the navigation key (scroll keys), select Menu >
Settings > My shortcuts > Navigation key. Scroll to the desired key, and select
Change and a function from the list. To remove a shortcut function from the key,
select (empty). To reassign a function for the key, select Assign. See "Shortcuts in
the standby mode," p. 18.
Voice commands
To call contacts and carry out phone functions, say the voice commands. Voice
commands are language-dependent. To set the language, see Voice playback
language in "Phone," p. 50.
To select the phone functions to activate with a voice commands, select Menu >
Settings > My shortcuts > Voice commands and a folder. Scroll to a function.
indicates that the voice tag is activated. To activate the voice tag, select Add. To
play the activated voice command, select Play. To use voice commands, see
"Enhanced voice dialing," p. 21.
To manage the voice commands, scroll to a phone function, and select from the
following options:
Edit or Remove — to change or deactivate the voice command of the selected
function
Add all or Remove all — to activate or deactivate voice commands to all functions
in the voice commands list
■ Connectivity
You can connect the phone to a compatible device using a Bluetooth wireless
technology or a USB data cable connection. You can also define the settings for
EGPRS dial-up connections.
44
S e t t i n g s
Bluetooth wireless technology
This device is compliant with Bluetooth Specification 2.0 + EDR supporting the
following profiles: generic access, generic object exchange, hands-free, headset,
object push, file transfer, dial-up networking, SIM access, and serial port. To
ensure interoperability between other devices supporting Bluetooth technology,
use Nokia approved enhancements for this model. Check with the manufacturers
of other devices to determine their compatibility with this device.
There may be restrictions on using Bluetooth technology in some locations.
Check with your local authorities or service provider.
Features using Bluetooth technology or allowing such features to run in the
background while using other features, increase the demand on battery power
and reduce the battery life.
Bluetooth technology allows you to connect the phone to a compatible
Bluetooth device within 10 meters (32 feet). Since devices using Bluetooth
technology communicate using radio waves, your phone and the other devices do
not need to be in direct line-of-sight, although the connection can be subject to
interference from obstructions such as walls or from other electronic devices.
Set up a Bluetooth connection
Select Menu > Settings > Connectivity > Bluetooth and from the following
options:
Bluetooth > On or Off — to activate or deactivate the Bluetooth function.
indicates that Bluetooth is activated.
Search for audio enhanc. — to search for compatible Bluetooth audio devices.
Select the device that you want to connect to the phone.
Paired devices — to search for any Bluetooth device in range. Select New to list
any Bluetooth device in range. Scroll to a device, and select Pair. Enter an agreed
Bluetooth passcode of the device (up to 16 characters) to associate (pair) the
device to your phone. You must only give this passcode when you connect to the
device for the first time. Your phone connects to the device, and you can start
data transfer.
Bluetooth wireless connection
Select Menu > Settings > Connectivity > Bluetooth. To check which Bluetooth
connection is currently active, select Active devices. To view a list of Bluetooth
devices that are currently paired with the phone, select Paired devices.
Select Options to access available options depending on the status of the device
and the Bluetooth connection.
45
S e t t i n g s
Bluetooth settings
To define how your phone is shown to other Bluetooth devices, select Menu >
Settings > Connectivity > Bluetooth > My phone's visibility or My phone's name.
If you are concerned about security, turn off the Bluetooth function, or set My
phone's visibility to Hidden. Always accept only Bluetooth communication from
others with whom you agree.
Packet data
General packet radio service (GPRS) is a network service that allows mobile
phones to send and receive data over an Internet protocol (IP)-based network. It
enables wireless access to data networks such as the Internet.
The applications that may use packet data are MMS, video streaming, browsing
sessions, remote SyncML, Java application downloading, and the PC dial-up.
To define how to use the service, select Menu > Settings > Connectivity > Packet
data > Packet data connection and from the following options:
When needed — to set the packet data connection to established when an
application needs it. The connection will be closed when the application is
terminated.
Always online — to set the phone to automatically connect to a packet data
network when you switch the phone on.
or indicates that the GPRS or
EGPRS service is available. If you receive a call or a text message or make a call
during a packet data connection,
connection is suspended (on hold).
or
indicates that the GPRS or EGPRS
Modem settings
To connect the phone, use Bluetooth wireless technology or a USB data cable
connection to a compatible PC, and use the phone as a modem to enable EGPRS
connectivity from the PC.
To define the settings for EGPRS connections from your PC, select Menu >
Settings > Connectivity > Packet data > Packet data settings > Active access
point, and activate the access point you want to use. Select Edit active access
point > Alias for access point, enter a name to change the access point settings,
and select OK. Select Packet data access point, enter the access point name (APN)
to establish a connection to an EGPRS network, and select OK.
To set the EGPRS dial-up service settings (access point name) on your PC, use the
Nokia Modem Options software. See "Nokia PC Suite," p. 78. If you have set the
settings both on your PC and on your phone, the PC settings are used.
46
S e t t i n g s
Data transfer
Synchronize your calendar, contacts data, and notes with another compatible
device (for example, a mobile phone), a compatible PC, or a remote Internet
server (network service).
Your phone allows data transfer with a compatible PC or another compatible
device when using the phone without a SIM card. Note that when you use the
phone without a SIM card, some functions appear dimmed in the menus and
cannot be used. Synchronizing with a remote Internet server is not possible
without a SIM card.
Transfer contact list
To copy or synchronize data from your phone, the name of the device and the
settings must be in the list of transfer contacts. If you receive data from another
device (for example, a compatible mobile phone), the corresponding transfer
contact is automatically added to the list, using the contact data from the other
device. Server synchronization and PC synchronization are the original items in
the list.
To add a new transfer contact to the list (for example, a mobile phone), select
Menu > Settings > Connectivity > Data transfer > Options > Add transfer
contact > Phone synchronization or Phone copy, and enter the settings according
to the transfer type.
To edit the copy and synchronize settings, select a contact from the transfer
contact list and Options > Edit.
Note: Every individual device must have its own entry in the transfer
contact list. Using one transfer contact for several devices is not
possible.
To delete a transfer contact, select it from the transfer contact list, select
Options > Delete, and confirm Delete transfer contact? . You cannot delete Server
synchronization or PC synchronization.
Data transfer with a device
For synchronization, Bluetooth wireless technology or a cable connection is used.
The other device is in the standby mode.
To start data transfer, select Menu > Settings > Connectivity > Data transfer and
the transfer contact from the list, other than Server synchronization or PC
synchronization. According to the settings, the selected data is copied or
synchronized. The other device also must be activated for receiving data.
47
S e t t i n g s
Synchronize from a PC
Before you synchronize data from calendar, notes, and contacts from a
compatible PC, you must install the Nokia PC Suite software of your phone on the
PC. Use Bluetooth wireless technology or a USB data cable for the
synchronization, and start the synchronization from the PC.
Synchronize from a server
To use a remote Internet server, you must subscribe to a synchronization service.
For more information and the settings required for this service, contact your
service provider. You may receive the settings as a configuration message. See
"Configuration settings service," p. 10 and "Configuration," p. 51.
If you have saved data on the remote Internet server, to synchronize your phone,
start the synchronization from your phone.
Select Menu > Settings > Connectivity > Data transfer > Server synchronization.
Depending on the settings, select Initializing synchronization or Initializing copy.
Synchronizing for the first time or after an interrupted synchronization may take
up to 30 minutes to complete, if the contacts or calendar are full.
USB data cable
You can use the USB data cable to transfer data between the phone and a
compatible PC or a printer supporting PictBridge. You can also use the USB data
cable with Nokia PC Suite.
To activate the phone for data transfer or image printing, connect the data cable;
when the phone displays USB data cable connected. Select mode., select OK.
Select from the following modes:
Default mode — to use the cable for PC Suite
Printing — to print images directly from the phone using a compatible printer
To change the USB mode, select Menu > Settings > Connectivity > USB data
cable > Default mode, Printing, or Data storage.
■ Call
Select Menu > Settings > Call and from the following options:
Call forwarding — to forward your incoming calls (network service). You may not
be able to forward your calls if some call restricting functions are active. See Call
restrictions in "Security," p. 52.
48
S e t t i n g s
Anykey answer > On — to answer an incoming call by briefly pressing any key
except the power key, the camera key, the left and right selection keys, or the end
key
Automatic redial > On — to make a maximum of 10 attempts to connect the call
after an unsuccessful call attempt
1-touch dialing > On — to dial the names and phone numbers assigned to the
1-touch-dialing keys 2 to 9 by pressing and holding the corresponding number
key
Call waiting > Activate — to have the network notify you of an incoming call
while you have a call in progress (network service). See "Call waiting," p. 23.
Summary after call > On — to briefly display the approximate duration and cost
(network service) of the call after each call
Send my caller ID > Yes — to show your phone number to the person you are
calling (network service). To use the setting agreed upon with your service
provider, select Set by network.
Line for outgoing calls — to select the phone line 1 or 2 for making calls if
supported by your SIM card (network service).
49
S e t t i n g s
■ Phone
Select Menu > Settings > Phone and from the following options:
Language settings — to set the display language of your phone, select Phone
language. If you select Automatic, the phone selects the language according to
the information on the SIM card.
To select the USIM card language, select SIM language.
To set a language for the voice playback, select Voice playback language. See
"Enhanced voice dialing," p. 21 and Voice commands in "My shortcuts," p. 43.
Security keyguard — to set the phone to ask for the security code when you
unlock the keyguard. Enter the security code, and select On.
Welcome note — to write the note you would like to have briefly displayed when
the phone is switched on
Flight query > On — the phone asks every time when it is switched on whether
the flight profile shall be used. With flight profile all radio connections are
switched off. The flight profile should be used in areas sensitive to radio
emissions.
Phone updates — to receive phone software updates from your service provider
(network service). This option may not be available, depending on your phone.
See "Phone software updates," p. 52.
Operator selection > Automatic — to set the phone to automatically select one of
the cellular networks available in your area. With Manual you can select a
network that has a roaming agreement with your service operator.
Confirm SIM serv. actions — See "SIM services," p. 70.
Help text activation — to select whether the phone shows help texts
Start-up tone > On— the phone plays a tone when it is switched on
■ Enhancements
This menu or the following options are displayed only if the phone is or has been
connected to a compatible mobile enhancement.
Select Menu > Settings > Enhancements. Select an enhancement, and
depending on the enhancement, from the following options:
Default profile — to select the profile that you want to be automatically activated
when you connect to the selected enhancement
50
S e t t i n g s
Automatic answer — to set the phone to answer an incoming call automatically
after 5 seconds. If Incoming call alert is set to Beep once or Off, automatic answer
is off.
Lights — to set the lights permanently On. Select Automatic to set the lights on
for 15 seconds after a key press.
TTY/TDD > Use TTY > Yes — to use the text phone settings instead of headset or
loopset settings
If your phone is provided with a hearing aid coil, select Hearing aid > T-coil
hearing aid mode > On to optimize the sound quality when using a T-coil hearing
aid. The
icon is displayed when the T-coil hearing aid mode is active.
■ Configuration
You can configure your phone with settings that are required for certain services
to function correctly. The services are multimedia messaging, IM,
synchronization, streaming, and browser. Your service provider may also send you
these settings. See "Configuration settings service," p. 10.
Select Menu > Settings > Configuration and from the following options:
Default config. settings — to view the service providers saved in the phone. Scroll
to a service provider, and select Details to view the applications that the
configuration settings of this service provider support. To set the configuration
settings of the service provider as default settings, select Options > Set as
default. To delete configuration settings, select Delete.
Activ. default in all apps. — to activate the default configuration settings for
supported applications
Preferred access point — to view the saved access points. Scroll to an access
point, and select Options > Details to view the name of the service provider, data
bearer, and packet data access point or GSM dial-up number.
Connect to serv. support — to download the configuration settings from your
service provider
Device manager settings — to allow or prevent the phone from receiving phone
software updates. This option may not be available, depending on your phone.
See "Phone software updates," p. 52.
Personal config. settings — to add new personal accounts for various services
manually and to activate or delete them. To add a new personal account if you
have not added any, select Add new; otherwise, select Options > Add new. Select
the service type, and select and enter each of the required parameters. The
51
S e t t i n g s
parameters differ according to the selected service type. To delete or activate a
personal account, scroll to it, and select Options > Delete or Activate.
■ Security
When security features that restrict calls are in use (such as call restricting,
closed user group, and fixed dialing), calls may be possible to the official
emergency number programmed into your device.
Select Menu > Settings > Security and from the following options:
PIN code request and UPIN code request — to set the phone to ask for your PIN or
UPIN code every time the phone is switched on. Some SIM cards do not allow the
code request to be turned off.
PIN2 code request — to select whether the PIN2 code is required when using a
specific phone feature which is protected by the PIN2 code. Some SIM cards do
not allow the code request to be turned off.
Call restrictions — to restrict calls to and from your phone (network service). A
restricting password is required.
Fixed dialing — to restrict your outgoing calls to selected phone numbers if this
function is supported by your SIM card
Closed user group — to specify a group of people whom you can call and who can
call you (network service)
Security level > Phone — to set the phone to ask for the security code whenever a
new SIM card is inserted into the phone. If you select Memory, the phone asks for
the security code when the SIM card memory is selected, and you want to change
the memory in use.
Access codes — to change the security code, PIN code, UPIN code, PIN2 code, or
restricting password
Code in use — to select whether the PIN code or UPIN code should be active
Authority certificates or User certificates — to view the list of the authority or
user certificates downloaded into your phone. See "Certificates," p. 76.
Security module settings — to view Security module details, activate Module PIN
request, or change the module PIN and signing PIN. See also "Access codes," p. 9.
■ Phone software updates
Your service provider may send phone software updates over the air directly to
your device. This option may not be available, depending on your phone.
52
S e t t i n g s
Warning: If you install a software update, you cannot use the device,
even to make emergency calls, until the update is completed and the
device is restarted. Be sure to backup data before accepting a software
update.
Settings
To allowed or disallow phone software updates, select Menu > Settings >
Configuration > Device manager settings > Service prov. sw updates and from
the following options:
Always allow — to perform all software downloads and updates automatically
Confirm first — to perform software downloads and updates only after your
confirmation (default setting)
Always reject — to decline all software updates
Depending on your settings you will be notified that a software update is
available for download or has been downloaded and installed automatically.
Request a software update
Select Menu > Settings > Phone > Phone updates to request available phone
software updates from your service provider. Select Current software details to
display the current software version and check whether an update is needed.
Select Download phone softw. to download and install a phone software update.
Follow the instructions on the display.
Install a software update
Select Install software update to start the installation when the installation is
cancelled after the download.
The software update may take several minutes. If there are problems with the
installation, contact your service provider.
■ Restore factory settings
To reset some of the menu settings to their original values, select Menu >
Settings > Restore factory sett.. Enter the security code. The names and phone
numbers saved in Contacts, are not deleted.
53
S e t t i n g s
54
O p e r a t o r m e n u
10. Operator menu
This menu lets you access a portal to services provided by your network operator.
The name and the icon depend on the operator. For more information contact
your network operator. If this menu is not displayed, the following menu numbers
change accordingly.
The operator can update this menu with a service message. For more information,
see "Service inbox," p. 74.
55
G a l l e r y
11. Gallery
In Gallery you can manage images, video clips, music files,
themes, graphics, tones, recordings, and received files. These files are stored in
the phone memory or a attached microSD memory card and may be arranged in
folders.
Your phone supports an activation key system to protect acquired content.
Always check the delivery terms of any content and activation key before
acquiring them, as they may be subject to a fee.
Copyright protections may prevent some images, music (including ringing tones),
and other content from being copied, modified, transferred, or forwarded.
To see the list of folders, select Menu > Gallery.
To see the available options of a folder, select a folder > Options.
To view the list of files in a folder, select a folder > Open.
To see the available options of a file, select a file > Options.
■ Print images
Your device supports Nokia XpressPrint. To connect it to a compatible printer use
a data cable or send the image using Bluetooth to a printer supporting Bluetooth
technology. See "Connectivity," p. 44.
You can print images that are in the JPEG format. The images taken with the
camera are automatically saved in the JPEG format.
Select the image you want to print and Options > Print.
■ Memory card
Keep all memory cards out of the reach of small children.
You can use the microSD memory card to store your multimedia files such as
video clips, music tracks, and sound files, photos, and messaging data, and to
back up information from phone memory.
Details of how you can use the memory card with other features and applications
of your phone are given in the sections describing these features and
applications. To insert and remove the microSD memory card, see "Insert a
microSD card," p. 13 and "Remove the microSD card," p. 13. The following options
may can also be accessed from Gallery.
56
G a l l e r y
Format the memory card
When a memory card is formatted, all data on the card is permanently lost.
Some memory cards are supplied preformatted and others require formatting.
Consult your retailer to find out if you must format the memory card before you
can use it.
1. Select Menu > Applications and the memory card folder
.
2. Select Options > Format memory card > Yes (to confirm).
3. When formatting is complete, enter a name for the memory card (up to 11
letters or numbers).
Lock the memory card
To set a password to lock your memory card to help prevent unauthorized use,
select Options > Set password.
You are asked to enter and confirm your password. The password can be up to
eight characters long.
The password is stored in your phone and you do not have to enter it again while
you are using the memory card on the same phone. If you want to use the
memory card on another phone, you are asked for the password.
Unlock a memory card
If you insert another password-protected memory card into your phone, you are
prompted to enter the password of the card. To unlock the card, select Options >
Delete password.
Once the password is removed, the memory card is unlocked and can be used on
another phone without a password.
Check memory consumption
To check the memory consumption of different data groups and the available
memory for installing new applications or software on your memory card, select
Options > Details.
57
M e d i a
12. Media
When taking and using images or video clips, obey all laws and respect local
customs as well as privacy and legitimate rights of others.
■ Camera
You can take photos or record video clips with the built-in camera.
Take a photo
To start the camera, press the camera key in the standby mode, or select Menu >
Media > Camera.
To take an image in landscape format,
hold the phone in a horizontal position.
Scroll left or right to change between the
camera Capture mode and the video
Record mode.
To zoom in and out in the camera mode,
scroll up and down, or press the volume up and down keys.
To take a photo, press the camera key. The phone saves the photo in Gallery >
Images.
To take a self-portrait, close the fold, and use the mini display as a view finder.
Press the camera key.
Select Options to set Night mode on if the lighting is dim, Self-timer on to
activate the self-timer, or Img. sequence on to take photos in a fast sequence.
With the highest image size setting, three photos can be taken in a sequence;
with other size settings, five photos can be taken.
Select Options > Settings >Image preview time and a preview time to display the
photo on the display. During the preview time, select Back to take another photo
or Send to send the photo as a multimedia message.
Your device supports an image capture resolution of 960 x 1280 pixels. The
image resolution in these materials may appear different.
58
M e d i a
Record a video clip
To select the video mode, scroll left or right, or select Options > Video. To start
the video recording, select Record. To pause the recording, select Pause; to
resume the recording, select Continue. To stop the recording, select Stop. The
phone saves the recording in Gallery > Video clips.
Camera options
To use a filter with the camera, select Options > Effects >False colors, Grayscale,
Sepia, Negative, or Solarize.
To change the camera settings, select Options > Settings.
■ Media player
With the media player you can view, play, and download files, such as images,
audio, video, and animated images. You can also view compatible streaming
videos from a network server (network service).
Select Menu > Media > Media player > Open gallery, Bookmarks, Go to address,
or Media downloads to select or download media.
Select Menu > Media > Media player > FF/Rew interval to set the step width for
fast forward or rewind.
Configuration for streaming
You may receive the configuration settings required for streaming as a
configuration message from the service provider. See "Configuration settings
service," p. 10. You can also enter the settings manually. See "Configuration," p.
51. To activate the settings, do the following:
1. Select Menu > Media > Media player > Streaming settings > Configuration.
Only the configurations that support streaming are displayed.
2. Select a service provider, Default, or Personal configuration for streaming.
3. Select Account and a streaming service account contained in the active
configuration settings.
■ Music player
Your phone includes a music player for listening to music tracks, recordings, or
other MP3 or AAC sound files that you have transferred to the phone with the
59
M e d i a
Nokia Audio Manager application, which is part of Nokia PC Suite. See "Nokia PC
Suite," p. 78.
Music files stored in a folder in the phone memory or in a folder of the
multimedia card are automatically detected and added to the default track list.
To open the music player, select Menu > Media > Music player.
Play music tracks
Warning! Listen to music at a moderate level. Continuous exposure to
high volume may damage your hearing.
When you open the Music player menu, the details of the first track on the
default track list are displayed. To play, select
.
To adjust the volume level, use the volume keys on the side of the phone.
To stop the playing, select
.
To skip to the next track, select
. To skip to the beginning of the previous
track, select
.
To rewind the current track, select and hold
. To fast forward the current
. Release the key at the position you want.
track, select and hold
Music player settings
In the Music player menu, the following options may be available:
Track list — View all the tracks available on the track list, and play the desired
track. To play a track, scroll to the desired track, and select Play.
If you select Options, you can refresh the track list (for example, after adding new
tracks to the list) and change the track list that is displayed when you open the
Music player menu if several track lists are available in the phone. You also may
send a track to another phone.
Play options — Select Random to play the tracks on the track list in random order.
Select Repeat to play the current track or the entire track list repeatedly. Select
Music source and a folder with music tracks.
Media equalizer — Select or define an equalizer setting. See "Equalizer," p. 61.
Loudspeaker or Headset— Listen to the music player using the phone loudspeaker
or headset. (Only if a headset is attached)
When using a headset, press the headset key to skip to the next track.
60
M e d i a
Web page — Access a Web page associated with the currently played track.
Dimmed if no Web page is available.
Music downloads— Connect to a browser service related to the current track. This
function is only available when the address of the service is included in the track.
■ Voice recorder
You can record pieces of speech, sound, or an active call, and save them in
Gallery. This is useful when recording a name and phone number to write down
later.
The recorder cannot be used when a data call or GPRS connection is active.
Record sound
1. Select Menu > Media > Voice recorder.
To use the graphical keys
,
, or
on the display, scroll left or right to
the desired key, and select it.
2. To start the recording, select
. To start the recording during a call, select
Options > Record. While recording a call, all parties to the call hear a faint
beeping sound. When recording a call, hold the phone in the normal position
near your ear.
3. To pause the recording, select
.
4. To end the recording, select
. The recording is saved in Gallery >
Recordings.
5. To listen to the latest recording, select Options > Play last recorded.
6. To send the last recording, select Options > Send last recorded.
7. To see the list of recordings in Gallery, select Options > Recordings list >
Recordings.
■ Equalizer
To control the sound quality when using the music player, amplify or diminish
frequency bands.
Select Menu > Media > Equalizer.
To activate a set, scroll to one of the equalizer sets, and select Activate.
61
M e d i a
To view, edit, or rename a selected set, select Options > View, Edit, or Rename.
Not all sets can be edited or renamed.
■ Stereo widening
Stereo widening enhances the audio output of the music player by enabling a
wider stereo sound effect. To change the setting, select Menu > Media > Stereo
widening.
62
O r g a n i z e r
13. Organizer
■ Alarm clock
You can set the phone to alarm at a desired time. Select Menu > Organizer >
Alarm clock.
To set the alarm, select Alarm time, and enter the alarm time. To change the
alarm time when the alarm time is set, select On.
To set the phone to alert you on selected days of the week, select Repeat alarm.
To select the alarm tone as the alarm tone, select Alarm tone.
To set a snooze time-out, select Snooze time-out and the time.
Stop the alarm
The phone sounds an alert tone, flashes Alarm!, and the current time is displayed,
even if the phone is switched off. To stop the alarm, select Stop. If you let the
phone continue to sound the alarm for a minute or select Snooze, the alarm stops
for the time you set in Snooze time-out, then resumes.
If the alarm time is reached while the device is switched off, the device switches
itself on and starts sounding the alarm tone. If you select Stop, the device asks
whether you want to activate the device for calls. Select No to switch off the
device or Yes to make and receive calls. Do not select Yes when wireless phone
use may cause interference or danger.
■ Calendar
Select Menu > Organizer > Calendar.
The current day is indicated by a frame. If there are any notes set for the day, the
day is in bold type, and the beginning of the note is displayed below the calendar.
To view the day notes, select View. To view a week, select Options > Week view.
To delete all notes in the calendar, select the month or week view, and Options >
Delete all notes.
Other options for the day view may be to make a note; delete, edit, move, or
repeat a note; copy a note to another day; send a note with Bluetooth
technology; or send a note to the calendar of another compatible phone as a text
message or multimedia message. In Settings you can set the date, time, time
zone, date or time format, date separator, default view, or the first day of the
63
O r g a n i z e r
week. In Auto-delete notes you can set the phone to delete old notes
automatically after a specified time.
Make a calendar note
Select Menu > Organizer > Calendar. Scroll to the date, and select Options >
Make a note and one of the following note types:
Meeting,
Call,
Birthday, Memo, or Reminder. Fill in the fields.
Note alarm
The phone displays the note, and if an alarm is set, sounds a tone. With a call note
on the display, to call the displayed number, press the call key. To stop the
alarm and to view the note, select View. To stop the alarm for 10 minutes, select
Snooze.
To stop the alarm without viewing the note, select Exit.
■ To-do list
To save a note for a task that you must do, select Menu > Organizer > To-do list.
To make a note if no note is added, select Add; otherwise, select Options > Add.
Fill in the fields, and select Save.
To view a note, scroll to it, and select View. While viewing a note, you can also
select an option to edit the attributes. You can also select an option to delete the
selected note and delete all the notes that you have marked as done.
You can sort the notes by priority or by deadline, send a note to another phone as
a text message or a multimedia message, save a note as a calendar note, or
access the calendar.
■ Notes
To write and send notes, select Menu > Organizer > Notes.
To make a note if no note is added, select Add; otherwise, select Options > Make
a note. Write the note, and select Save.
Other options include deleting and editing a note. While editing a note, you can
also exit the text editor without saving the changes. You can send the note to
compatible devices by Bluetooth wireless technology, text message, or a
multimedia message.
64
O r g a n i z e r
■ Calculator
The calculator in your phone provides basic arithmetic and trigonometric
functions, calculates the square and the square root, the inverse of a number, and
converts currency values.
Note: This calculator has limited accuracy and is designed for simple
calculations.
Select Menu > Organizer > Calculator. When 0 is displayed on the screen, enter
the first number in the calculation. Press # for a decimal point. Scroll to the
desired operation or function, or select it from the Options. Enter the second
number. Repeat this sequence as many times as it is necessary. To start a new
calculation, select and hold Clear.
To perform a currency conversion, select Menu > Organizer > Calculator. To save
the exchange rate, select Options > Exchange rate. Select either of the displayed
options. Enter the exchange rate, press # for a decimal point, and select OK. The
exchange rate remains in the memory until you replace it with another one. To
perform the currency conversion, enter the amount to be converted, and select
Options > To home or To foreign.
Note: When you change base currency, you must enter new exchange
rates because all previously set exchange rates are cleared.
■ Countdown timer
Select Menu > Organizer > Countdown timer. Enter the alarm time in hours,
minutes, and seconds, and select OK. If you wish, write your own note text that is
displayed when the time expires. To start the countdown timer, select Start. To
change the countdown time, select Change time. To stop the timer, select Stop
timer.
If the alarm time is reached when the phone is in the standby mode, the phone
sounds a tone and flashes the note text if it is set or Countdown completed. To
stop the alarm, press any key. If no key is pressed, the alarm automatically stops
within 60 seconds. To stop the alarm and delete the note text, select Exit. To
restart the countdown timer, select Restart.
■ Stopwatch
You can measure time, take intermediate times, or take lap times using the
stopwatch. During timing, the other functions of the phone can be used. To set
the stopwatch timing in the background, press the end key.
65
O r g a n i z e r
Using the stopwatch or allowing it to run in the background when using other
features increases the demand on battery power and reduces the battery life.
Select Menu > Organizer > Stopwatch and from the following options:
Split timing — to take intermediate times. To start the time observation, select
Start. Select Split eact time you want to take an intermediate time. To stop the
time observation, select Stop.
To save the measured time, select Save.
To start the time observation again, select Options > Start. The new time is added
to the previous time. To reset the time without saving it, select Reset.
Lap timing — to take lap times
Continue — to view the timing that you have set in the background
Show last time — to view the most recently measured time if the stopwatch is not
reset
View times or Delete times — to view or delete the saved times
66
A p p l i c a t i o n s
14. Applications
In this menu you can manage applications and games. These files are stored in
the phone memory or a attached microSD memory card and may be arranged in
folders.
For options to format or lock and unlock the memory card, see "Memory card," p.
56.
■ Launch a game
Your phone software includes some games.
Select Menu > Applications > Games. Scroll to the desired game, and select
Open.
■ Launch an application
Your phone software includes some Java applications.
Select Menu > Applications > Collection. Scroll to an application, and select
Open.
■ Download an application
Your phone supports J2ME Java applications. Make sure that the application is
compatible with your phone before downloading it.
Important: Only install and use applications and other software from
sources that offer adequate security and protection against harmful
software.
You can download new Java applications and games in different ways.
Use the Nokia Application Installer from PC Suite to download the applications to
your phone, or select Menu > Applications > Options > Downloads >
Application downloads; the list of available bookmarks is displayed. See
"Bookmarks," p. 73.
For the availability of different services, pricing, and tariffs, contact your service
provider.
Your device may have some bookmarks loaded for sites not affiliated with Nokia.
Nokia does not warrant or endorse these sites. If you choose to access them, you
67
A p p l i c a t i o n s
should take the same precautions, for security or content, as you would with any
Internet site.
■ Presenter
The Nokia Presenter PC application enables you to control slide presentations
(compatible with Microsoft Office PowerPoint), a software DVD, an MP3 player,
or other PC applications remotely from your device.
To use applications other than slide presentations and desktop mode, you must
create a corresponding custom profile on the PC application.
Before you can use the application you must do the following:
1. Install the Nokia Presenter PC application on your PC.
This component is available for download on the Nokia Web site..
2. Launch and configure the PC component. Make sure that the selected
incoming Bluetooth serial port (COM port) corresponds to the one defined in
the Bluetooth software settings on the Bluetooth device of your PC. For
details, refer to the PC component documentation and "Set up a Bluetooth
connection," p. 45.
3. Open the slide presentation, or start the application you want to control
remotely from your phone.
Select Applications > Collection > Presenter > Connect and the device you want
to connect to.
When the Bluetooth Connection Successful dialog appears on your PC screen,
you must click on it to confirm the Bluetooth connection.
The list of available application types is displayed. Select Open to access the
desired application. Select Options > Settings to set the Font size for the speaker
notes, and Timer (in minutes) to optimize the slide presentation time available. To
save the settings, select Options > Back.
After you select the slide presentation, to browse or skip slide, or jump ahead, use
the 4-way scroll key. To view your speaker notes, select Notes. To use the pointer,
select Pointer to activate a small black round marker that you control with the
scroll key. Select Options > Slide list to return to the slide list. Select Options >
Applications list to return to the list of applications.
To control the mouse pointer (the cursor) remotely from the phone, select the
desktop mode. After you open the desktop, the phone automatically controls your
68
A p p l i c a t i o n s
mouse pointer. To return to the list of applications, select Options > Applications
list.
To quit the presenter, select Options > Exit.
69
S I M s e r v i c e s
15. SIM services
Your SIM card may provide additional services. You can access
this menu only if it is supported by your SIM card. The name and contents of the
menu depend on the available services.
For availability and information on using SIM card services, contact your SIM
card vendor. This may be the service provider, network operator, or other vendor.
To set the phone to show you the confirmation messages sent between your
phone and the network when you are using the SIM services, select Menu >
Settings > Phone > Confirm SIM serv. actions > Yes.
Accessing these services may involve sending messages or making a phone call
for which you may be charged.
70
W e b
16. Web
You can access various mobile Internet services with your phone
browser.
Important: Use only services that you trust and that offer adequate
security and protection against harmful software.
Check the availability of these services, pricing, tariffs, and instructions with your
service provider.
With the phone browser you can view the services that use wireless markup
language (WML) or extensible hypertext markup language (XHTML) on their
pages. Appearance may vary due to screen size. You may not be able to view all
details of the Internet pages.
■ Set up browsing
You may receive the configuration settings required for browsing as a
configuration message from the service provider that offers the service that you
want to use. See "Configuration settings service," p. 10. You can also enter all the
configuration settings manually. See "Configuration," p. 51.
■ Connect to a service
Ensure that the correct configuration settings of the service are activated.
1. To select the settings for connecting to the service, select Menu > Web >
Settings > Configuration settings.
2. Select Configuration. Only the configurations that support a browsing service
are displayed. Select a service provider, Default, or Personal configuration for
browsing. See "Set up browsing," p. 71.
3. Select Account and a browsing service account contained in the active
configuration settings.
4. Select Display terminal window > Yes to perform manual user authentication
for intranet connections.
Make a connection to the service in one of the following ways:
•
•
Select Menu > Web > Home; or in the standby mode, press and hold 0.
To select a bookmark of the service, select Menu > Web > Bookmarks.
71
W e b
•
•
To select the last URL, select Menu > Web > Last web address.
To enter the address of the service, select Menu > Web > Go to address. Enter
the address of the service, and select OK.
■ Browse pages
After you make a connection to the service, you can start browsing its pages. The
function of the phone keys may vary in different services. Follow the text guides
on the phone display. For more information, contact your service provider.
Browse with phone keys
To browse through the page, scroll in any direction.
To select a highlighted item, press the call key, or select Select.
To enter letters and numbers, press the 0 to 9 keys. To enter special characters,
press
.
*
Options while browsing
Select from the following options:
Home — to return to your start page
Shortcuts — to open a new list of options that are specific to the page. This
option is only available if the page contains shortcuts.
Add bookmark — to save the page as a bookmark
Bookmarks — to access the list of bookmarks. See "Bookmarks," p. 73.
Page options — to show the list of options for the active page
History — to get a list showing the last visited URLs
Downloads — to show the list of bookmarks for downloading
Other options — to show a list of other options
Reload — to reload and update the current page
The service provider may also offer other options.
Direct calling
While browsing, you can make a phone call and save a name and a phone number
from a page.
72
W e b
■ Bookmarks
You can save page addresses as bookmarks in the phone memory.
1. While browsing, select Options > Bookmarks; or in the standby mode, select
Menu > Web > Bookmarks.
2. Scroll to a bookmark, and select it, or press the call key to make a connection
to the page associated with the bookmark.
3. Select Options to view, edit, delete, or send the bookmark; to create a new
bookmark; or to save the bookmark to a folder.
Your device may have some bookmarks loaded for sites not affiliated with Nokia.
Nokia does not warrant or endorse these sites. If you choose to access them, you
should take the same precautions, for security or content, as you would with any
Internet site.
Receive a bookmark
When you have received a bookmark that is sent as a bookmark, 1 bookmark
received is displayed. To view the bookmark, select Show.
■ Appearance settings
While browsing, select Options > Other options > Appearance settings; or in the
standby mode, select Menu > Web > Settings > Appearance settings and from
the following options:
Text wrapping > On — to set the text to continue on the next line on the display.
If you select Off, the text is abbreviated.
Font size — to set the font size
Show images > No — to hide images on the page. This can speed up the browsing
of pages that contain a lot of images.
Alerts > Alert for unsecure conn. > Yes — to set the phone to alert when a secure
connection changes to an unsecure one during browsing
Alerts > Alert for unsecure items > Yes — to set the phone to alert when a secure
page contains an unsecure item. These alerts do not guarantee a secure
connection. For more information, see "Browser security," p. 75.
Character encoding > Content encoding — to select the encoding for the browser
page content
73
W e b
Character encoding > Unicode (UTF-8) web add. > On — to set the phone to send
a URL as a UTF-8 encoding. You may need this setting when you access a Web
page created in foreign language.
Screen size > Full or Small— to set the screen layout
JavaScript > Enable — to enable the Java scripts
■ Security settings
Cookies
A cookie is data that a site saves in the cache memory of your phone. Cookies are
saved until you clear the cache memory. See "Cache memory," p. 75.
While browsing, select Options > Other options > Security > Cookie settings; or
in the standby mode, select Menu > Web > Settings > Security settings >
Cookies. To allow or prevent the phone from receiving cookies, select Allow or
Reject.
Scripts over secure connection
You can select whether to allow the running of scripts from a secure page. The
phone supports WML scripts.
While browsing, to allow the scripts, select Options > Other options > Security >
WMLScript settings; or in the standby mode, select Menu > Web > Settings >
Security settings > WMLScripts in sec. conn. > Allow.
■ Download settings
To automatically save all downloaded files in Gallery, select Menu > Web >
Settings > Downloading settings > Automatic saving > On.
■ Service inbox
The phone is able to receive service messages sent by your service provider
(network service). Service messages are notifications (for example, news
headlines), and they may contain a text message or an address of a service.
To access the Service inbox in the standby mode when you have received a
service message, select Show. If you select Exit, the message is moved to the
Service inbox. To access the Service inbox later, select Menu > Web > Service
inbox.
74
W e b
To access the Service inbox while browsing, select Options > Other options >
Service inbox. Scroll to the message you want, and to activate the browser and
download the marked content, select Retrieve. To display detailed information on
the service notification or to delete the message, select Options > Details or
Delete.
Service inbox settings
Select Menu > Web > Settings > Service inbox settings.
To set whether you want to receive service messages, select Service messages >
On or Off.
To set the phone to receive service messages only from content authors approved
by the service provider, select Message filter > On. To view the list of the
approved content authors, select Trusted channels.
To set the phone to automatically activate the browser from the standby mode
when the phone has received a service message, select Automatic connection >
On. If you select Off, the phone activates the browser only after you select
Retrieve when the phone has received a service message.
■ Cache memory
A cache is a memory location that is used to store data temporarily. If you have
tried to access or have accessed confidential information requiring passwords,
empty the cache after each use. The information or services you have accessed is
stored in the cache.
To empty the cache while browsing, select Options > Other options > Clear the
cache; in the standby mode, select Menu > Web > Clear the cache.
■ Browser security
Security features may be required for some services, such as online banking or
shopping. For such connections you need security certificates and possibly a
security module, which may be available on your SIM card. For more information,
contact your service provider.
Security module
The security module improves security services for applications requiring a
browser connection, and allows you to use a digital signature. The security
75
W e b
module may contain certificates as well as private and public keys. The
certificates are saved in the security module by the service provider.
To view or change the security module settings, select Menu > Settings >
Security > Security module settings.
Certificates
Important: Even if the use of certificates makes the risks involved in
remote connections and software installation considerably smaller,
they must be used correctly in order to benefit from increased security.
The existence of a certificate does not offer any protection by itself; the
certificate manager must contain correct, authentic, or trusted certificates for
increased security to be available. Certificates have a restricted lifetime. If
Expired certificate or Certificate not valid yet is shown even if the certificate
should be valid, check that the current date and time in your device are correct.
Before changing any certificate settings, you must make sure that you really trust
the owner of the certificate and that the certificate really belongs to the listed
owner.
There are three kinds of certificates: server certificates, authority certificates, and
user certificates. You may receive these certificates from your service provider.
Authority certificates and user certificates may also be saved in the security
module by the service provider.
To view the list of the authority or user certificates downloaded into your phone,
select Menu > Settings > Security > Authority certificates or User certificates.
is displayed during a connection, if the data transmission between the
phone and the content server is encrypted.
The security icon does not indicate that the data transmission between the
gateway and the content server (or place where the requested resource is stored)
is secure. The service provider secures the data transmission between the
gateway and the content server.
Digital signature
You can make digital signatures with your phone if your SIM card has a security
module. Using the digital signature can be the same as signing your name to a
paper bill, contract, or other document.
To make a digital signature, select a link on a page, for example, the title of the
book you want to buy and its price. The text to sign is displayed, which may
include the amount and date.
76
W e b
Check that the header text is Read and that the digital signature icon
is
displayed.
If the digital signature icon does not appear, there is a security breach, and you
should not enter any personal data such as your signing PIN.
To sign the text, read all of the text first, and select Sign.
The text may not fit within a single screen. Therefore, make sure to scroll through
and read all of the text before signing.
Select the user certificate you want to use. Enter the signing PIN (see "Access
codes," p. 9), and select OK. The digital signature icon disappears, and the service
may display a confirmation of your purchase.
77
P C c o n n e c t i v i t y
17. PC connectivity
You can send and receive e-mail, and access the Internet when your phone is
connected to a compatible PC through a Bluetooth or a data cable connection.
You can use your phone with a variety of PC connectivity and data
communications applications.
■ Nokia PC Suite
With Nokia PC Suite you can synchronize contacts, calendar, notes, and to-do
notes between your phone and the compatible PC or a remote Internet server
(network service). You may find more information and PC Suite on the Nokia Web
■ EGPRS, HSCSD, and CSD
With your phone you can use the enhanced GPRS (EGPRS), general packet radio
service (GPRS), high-speed circuit switched data (HSCSD), and circuit-switched
data (CSD, GSM data) data services.
For availability and subscription to data services, contact your network operator
or service provider.
The use of HSCSD services consumes the phone battery faster than normal voice
or data calls. You may need to connect the phone to a charger for the duration of
data transfer.
See "Modem settings," p. 46.
■ Data communication applications
For information on using a data communication application, refer to the
documentation provided with it.
Making or answering phone calls during a computer connection is not
recommended, as it might disrupt the operation.
For better performance during data calls, place the phone on a stationary surface
with the keypad facing downward. Do not move the phone by holding it in your
hand during a data call.
78
B a t t e r y i n f o r m a t i o n
18. Battery information
■ Charging and discharging
Your device is powered by a rechargeable battery. The full performance of a new
battery is achieved only after two or three complete charge and discharge cycles.
The battery can be charged and discharged hundreds of times, but it will
eventually wear out. When the talk and standby times are noticeably shorter
than normal, replace the battery. Use only Nokia approved batteries, and
recharge your battery only with Nokia approved chargers designated for this
device.
If a replacement battery is being used for the first time or if the battery has not
been used for a prolonged period, it may be necessary to connect the charger and
then disconnect and reconnect it to start the charging.
Unplug the charger from the electrical plug and the device when not in use. Do
not leave fully charged battery connected to a charger, since overcharging may
shorten its lifetime. If left unused, a fully charged battery will lose its charge over
time.
If the battery is completely discharged, it may take a few minutes before the
charging indicator appears on the display or before any calls can be made.
Use the battery only for its intended purpose. Never use any charger or battery
that is damaged.
Do not short-circuit the battery. Accidental short-circuiting can occur when a
metallic object such as a coin, clip, or pen causes direct connection of the
positive (+) and negative (-) terminals of the battery. (These look like metal strips
on the battery.) This might happen, for example, when you carry a spare battery
in your pocket or purse. Short-circuiting the terminals may damage the battery
or the connecting object.
Leaving the battery in hot or cold places, such as in a closed car in summer or
winter conditions, will reduce the capacity and lifetime of the battery. Always try
to keep the battery between 15°C and 25°C (59°F and 77°F). A device with a hot
or cold battery may not work temporarily, even when the battery is fully charged.
Battery performance is particularly limited in temperatures well below freezing.
Do not dispose of batteries in a fire as they may explode. Batteries may also
explode if damaged. Dispose of batteries according to local regulations. Please
recycle when possible. Do not dispose as household waste.
79
B a t t e r y i n f o r m a t i o n
■ Nokia battery authentication
Always use original Nokia batteries for your safety. To check that you are getting
an original Nokia battery, purchase it from an authorized Nokia dealer, look for
the Nokia Original Enhancements logo on the packaging, and inspect the
hologram label using the following steps:
Successful completion of the four steps is not a total assurance of the
authenticity of the battery. If you have any reason to believe that your battery is
not an authentic original Nokia battery, you should refrain from using it, and take
it to the nearest authorized Nokia service point or dealer for assistance. Your
authorized Nokia service point or dealer will inspect the battery for authenticity.
If authenticity cannot be verified, return the battery to the place of purchase.
Authenticate hologram
1. When looking at the hologram on the label, you
should see the Nokia connecting hands symbol from
one angle and the Nokia Original Enhancements
logo when looking from another angle.
2. When you angle the hologram left, right, down, and
up, you should see 1, 2, 3, and 4 dots on each side
respectively.
3. Scratch the side of the label to reveal a 20-digit
code, for example, 12345678919876543210. Turn
the battery so that the numbers are facing upwards.
The 20-digit code reads starting from the number at
the top row followed by the bottom row.
4. Confirm that the 20-digit code is valid by following the instructions at
80
B a t t e r y i n f o r m a t i o n
What if your battery is not authentic?
If you cannot confirm that your Nokia battery with the hologram on the label is
an authentic Nokia battery, please do not use the battery. Take it to the nearest
authorized Nokia service point or dealer for assistance. The use of a battery that
is not approved by the manufacturer may be dangerous and may result in poor
performance and damage to your device and its enhancements. It may also
invalidate any approval or warranty applying to the device.
81
C a r e a n d m a i n t e n a n c e
Care and maintenance
Your device is a product of superior design and craftsmanship and should be
treated with care. The suggestions below will help you protect your warranty
coverage.
•
Keep the device dry. Precipitation, humidity and all types of liquids or
moisture can contain minerals that will corrode electronic circuits. If your
device does get wet, remove the battery and allow the device to dry
completely before replacing it.
•
•
•
Do not use or store the device in dusty, dirty areas. Its moving parts and
electronic components can be damaged.
Do not store the device in hot areas. High temperatures can shorten the life of
electronic devices, damage batteries, and warp or melt certain plastics.
Do not store the device in cold areas. When the device returns to its normal
temperature, moisture can form inside the device and damage electronic
circuit boards.
•
•
Do not attempt to open the device other than as instructed in this guide.
Do not drop, knock, or shake the device. Rough handling can break internal
circuit boards and fine mechanics.
•
•
•
•
•
Do not use harsh chemicals, cleaning solvents, or strong detergents to clean
the device.
Do not paint the device. Paint can clog the moving parts and prevent proper
operation.
Do not touch the main display with hard or angular materials. Objects like
earrings or jewellery may scratch the display.
Use a soft, clean, dry cloth to clean any lenses (such as camera, proximity
sensor, and light sensor lenses).
Use only the supplied or an approved replacement antenna. Unauthorized
antennas, modifications, or attachments could damage the device and may
violate regulations governing radio devices.
•
•
Use chargers indoors.
Always create a backup of data you want to keep (such as contacts and
calendar notes) before sending your device to a service facility.
All of the above suggestions apply equally to your device, battery, charger, or any
enhancement. If any device is not working properly, take it to the nearest
authorized service facility for service.
82
A d d i t i o n a l s a f e t y i n f o r m a t i o n
Additional safety information
Your device and its enhancements may contain small parts. Keep them out of the
reach of small children.
■ Operating environment
Remember to follow any special regulations in force in any area, and always
switch off your device when its use is prohibited or when it may cause
interference or danger. Use the device only in its normal operating positions. This
device meets RF exposure guidelines when used either in the normal use position
against the ear or when positioned at least 2.2 centimeters (7/8 inch) away from
the body. When a carry case, belt clip or holder is used for body-worn operation,
it should not contain metal and should position the device the above-stated
distance from your body.
To transmit data files or messages, this device requires a quality connection to
the network. In some cases, transmission of data files or messages may be
delayed until such a connection is available. Ensure that the above separation
distance instructions are followed until the transmission is completed.
Parts of the device are magnetic. Metallic materials may be attracted to the
device. Do not place credit cards or other magnetic storage media near the
device, because information stored on them may be erased.
■ Medical devices
Operation of any radio transmitting equipment, including wireless phones, may
interfere with the functionality of inadequately protected medical devices.
Consult a physician or the manufacturer of the medical device to determine if
they are adequately shielded from external RF energy or if you have any
questions. Switch off your device in health care facilities when any regulations
posted in these areas instruct you to do so. Hospitals or health care facilities may
be using equipment that could be sensitive to external RF energy.
Pacemakers
Pacemaker manufacturers recommend that a minimum separation of
15.3 centimeters (6 inches) be maintained between a wireless phone and a
pacemaker to avoid potential interference with the pacemaker. These
recommendations are consistent with the independent research by and
recommendations of Wireless Technology Research. Persons with pacemakers
should do the following:
83
A d d i t i o n a l s a f e t y i n f o r m a t i o n
•
Always keep the device more than 15.3 centimeters (6 inches) from the
pacemaker
•
•
Not carry the device in a breast pocket
Hold the device to the ear opposite the pacemaker to minimize the potential
for interference.
If you suspect interference, switch off your device, and move the device away.
Hearing aids
Some digital wireless devices may interfere with some hearing aids. If
interference occurs, consult your service provider.
■ Vehicles
RF signals may affect improperly installed or inadequately shielded electronic
systems in motor vehicles such as electronic fuel injection systems, electronic
antiskid (antilock) braking systems, electronic speed control systems, and air bag
systems. For more information, check with the manufacturer or its representative
of your vehicle or any equipment that has been added.
Only qualified personnel should service the device, or install the device in a
vehicle. Faulty installation or service may be dangerous and may invalidate any
warranty that may apply to the device. Check regularly that all wireless device
equipment in your vehicle is mounted and operating properly. Do not store or
carry flammable liquids, gases, or explosive materials in the same compartment
as the device, its parts, or enhancements. For vehicles equipped with an air bag,
remember that air bags inflate with great force. Do not place objects, including
installed or portable wireless equipment in the area over the air bag or in the air
bag deployment area. If in-vehicle wireless equipment is improperly installed and
the air bag inflates, serious injury could result.
Using your device while flying in aircraft is prohibited. Switch off your device
before boarding an aircraft. The use of wireless teledevices in an aircraft may be
dangerous to the operation of the aircraft, disrupt the wireless telephone
network, and may be illegal.
■ Potentially explosive environments
Switch off your device when in any area with a potentially explosive atmosphere
and obey all signs and instructions. Potentially explosive atmospheres include
areas where you would normally be advised to turn off your vehicle engine.
Sparks in such areas could cause an explosion or fire resulting in bodily injury or
even death. Switch off the device at refueling points such as near gas pumps at
service stations. Observe restrictions on the use of radio equipment in fuel
84
A d d i t i o n a l s a f e t y i n f o r m a t i o n
depots, storage, and distribution areas; chemical plants; or where blasting
operations are in progress. Areas with a potentially explosive atmosphere are
often but not always clearly marked. They include below deck on boats, chemical
transfer or storage facilities, vehicles using liquefied petroleum gas (such as
propane or butane), and areas where the air contains chemicals or particles such
as grain, dust, or metal powders.
■ Emergency calls
Important: Wireless phones, including this device, operate using radio
signals, wireless networks, landline networks, and user-programmed
functions. Because of this, connections in all conditions cannot be
guaranteed. You should never rely solely on any wireless device for
essential communications like medical emergencies.
To make an emergency call:
1. If the device is not on, switch it on. Check for adequate signal strength.
Some networks may require that a valid SIM card is properly inserted in the
device.
2. Press the end key as many times as needed to clear the display and ready the
device for calls.
3. Enter the official emergency number for your present location. Emergency
numbers vary by location.
4. Press the call key.
If certain features are in use, you may first need to turn those features off before
you can make an emergency call. Consult this guide or your service provider for
more information.
When making an emergency call, give all the necessary information as accurately
as possible. Your wireless device may be the only means of communication at the
scene of an accident. Do not end the call until given permission to do so.
85
A d d i t i o n a l s a f e t y i n f o r m a t i o n
■ Certification information (SAR)
This mobile device meets guidelines for exposure to radio waves
Your mobile device is a radio transmitter and receiver. It is designed not to
exceed the limits for exposure to radio waves recommended by international
guidelines. These guidelines were developed by the independent scientific
organization ICNIRP and include safety margins designed to assure the
protection of all persons, regardless of age and health.
The exposure guidelines for mobile devices employ a unit of measurement known
as the Specific Absorption Rate or SAR. The SAR limit stated in the ICNIRP
guidelines is 2.0 watts/kilogram (W/kg) averaged over 10 grams of tissue. Tests
for SAR are conducted using standard operating positions with the device
transmitting at its highest certified power level in all tested frequency bands. The
actual SAR level of an operating device can be below the maximum value
because the device is designed to use only the power required to reach the
network. That amount changes depending on a number of factors such as how
close you are to a network base station. The highest SAR value under the ICNIRP
guidelines for use at the ear for device type RM-126 is 0.76 W/kg.
Use of device accessories and enhancements may result in different SAR values.
SAR values may vary depending on national reporting and testing requirements
and the network band. Additional SAR information may be provided under
Your mobile device is also designed to meet the requirements for exposure to
radio waves established by the Federal Communications Commission (USA) and
Industry Canada. These requirements set a SAR limit of 1.6 W/kg averaged over
1 gram of tissue. The highest SAR value reported under this standard during
product certification for use at the ear for device type RM-126 is 0.89 W/kg, and
when properly worn on the body for device type RM-126 is 0.93 W/kg .
fccid by searching the equipment authorization system using
FCC ID: PPIRM-126.
86
A d d i t i o n a l s a f e t y i n f o r m a t i o n
■ Technical Information
Feature
Weight
Size
Specification
112 g (3.95 oz)
Volume: 75 cm3 (4.6 in3)
Length: 91.7 mm (3.61 in)
Width: 47.8 mm (1.88 in)
Thickness: < 20 mm (0.8 in)
Frequency range
RM-126
EGSM 850
824–849 MHz (TX)
869–894 MHz (RX)
EGSM 900
880–915 MHz (TX)
925–960 MHz (RX)
EGSM 1800
1710–1785 MHz (TX)
1805–1865 MHz (RX)
EGSM 1900
1850–1910 MHz (TX)
1930–1990 MHz (RX
Transmitter output power Up to 2 W
Battery voltage
3.7 V dc
BL-4C, 820 mAh
Operating times
Standby time: up to 240 hours
Talk time: up to 3.4 hours
Operating temperature
15°C to + 25°C
(59°F to + 77°F)
87
INDEX
Numerics1-touch dialing 22, 41
waiting 23
calls
1-touch dialing 21
A
access codes 10
accessories. See enhancements.active
standby 17, 42
international 21
making of 21
reject 22
alarm clock 63
voice dialing 21
antenna 15
camera
applications
key 16
collection 67
download 10
settings 59
audio messages 32
take a photo 58
zoom 16
care 82
B
certificates 76
certification information 86
character case 24
charge the battery 13
circuit switched data 78
clock settings 43
battery
authentication 80
charging 13, 79
discharging 79
installation 12
Bluetooth 45
bookmarks 73
browser
setting service 10
appearance settings 73
bookmarks 73
browsing pages 72
cache memory 75
certificates 76
cookies 74
digital signature 76
security 74
security module 75
set up 71
copy 37
delete 37
edit 37
groups 38
my numbers 38
save 36
search 36
service numbers 38
settings 38
business cards 37
speed dialing 38
cookies 74
C
countdown timer 65
CSD. See circuit switched data.
cache memory 75
calculator 65
calendar 63
call
D
functions 21
key 16
log 40
options 23
register. See call log.
settings 48
data
cable 48
communication 78
transfer 47
date settings 43
delete messages 33
88
digital signature 76
display 16, 17
downloads
keypad lock 19
keys
call key 16
applications 10
content 10
end key 16
keyguard 19
settings 74
power on/off 16
scroll key 16
selection keys 16, 17
E
earpiece 16
EGPRS. See packet data.
emergency calls 85
end
L
call 21
key 16
language settings 50
lights 51
enhancements 8, 50
equalizer 61
explosive environments 84
log 40
loudspeaker 16, 23
F
M
factory settings 53
flash messages 32
main display 16, 17, 42
maintenance 82
media player 59
memory card 56
formatting 57
G
gallery 56
games 67
GPRS 46
locking 57
menu 26
message center number 27
message folders 31
message settings
general settings 34
multimedia messages 35
text messages 34
messages
H
handsfree. See loudspeaker.
hearing aid 51, 84
high-speed circuit switched data 78
HSCSD. See high-speed circuit
switched data.
I
audio message 32
cancel sending 30
delete 33
flash message 32
info messages 33
length indicator 27
message settings 34
service commands 33
text 27
indicators 18
info messages 33
installation
battery 12
SIM card 12
Internet
K
voice message 33
write text message 27
microphone 16
keyguard 19
keypad 16
89
mini display 43
R
MMS. See multimedia messages.
multimedia messages 29, 30
music player 59
record sound 61
recorder 61
N
navigation 26
network
S
safety
name on display 17
services 7
additional information 83
certification information 86
emergency calls 85
notes 64
numbers 38
O
hearing aid 84
pacemakers 83
SAR 86
offline mode 19
operator menu 55
organizer 63
overview functions 9
vehicles 84
SAR 86
P
screen saver 42
scroll key. See navigation key.
scrolling 26
pacemakers 83
packet data 46, 78
parts 16
PC connectivity 78
PC Suite 78
security
codes 9
phone
module 75
care 82
settings 52
configuration 51
keys 16
selection keys 16, 17
service
maintenance 82
open 14
commands 33
inbox 74
parts 16
messages 74
settings 50
numbers 38
updates 50, 53
phone lock. See keypad lock.
PictBridge 48
PIN codes 9, 14
Pop-Port connector 16
power key 16
predictive text input 24
presenter 68
services, connect to
settings
active standby 42
call 48
camera 59
clock 43
configuration 51
connectivity 44
data transfer 47
date 43
downloads 74
enhancements 50
fold animation 42
GPRS, EGPRS 46
print images 56
profiles 41
PUK codes 10
pushed messages 74
90
main display 42
messages 34
writing 24
mini display 43
my shortcuts 43
phone 50
themes 41
time settings 43
tones 41
traditional text input 25
TTY 51
profiles 41
restore factory settings 53
screen saver 42
security 52
service inbox 75
standby mode 42
themes 41
U
UPIN 14
time 43
tones 41
USB data cable 48
wallpaper 42
V
vehicles 84
video clip 59
voice
shared memory 8
shortcuts 18, 43
signal strength 17
SIM
commands 44
dialing 21
card 19
messages 33
recorder 61
volume 16
volume key 16
card installation 12
messages 28
services 70
SMS. See text messages
software updates 50, 53
speaker phone 16
standby mode 17, 43
status indicators 17
stereo widening 62
stopwatch 65
W
wallpaper 42
Web
bookmarks 73
connect 71
strap 15
wireless markup language 71
wrist strap 15
write text 24
streaming service 59
switch on and off 14
swivel 42
synchronization 47
X
XHTML 71
XpressPrint 56
T
text
character case 24
message 27
Z
phone 51
predictive text input 24
zoom key 16
91
92
93
94
95
|