Mounting
MODEL 3966
Wireless Keyless Entry System
How Your Keyless Entry
Operates Your Opener
NOTE: With new installations, it is
recommended that the keyless entry be
programmed before mounting to wall.
Pre-drill a 5/64 pilot
hole 3/4" deep
Locate Keyless Entry Unit: within sight of door,
at a minimum height of 5 feet so it cannot be
reached by small children, and away from all
moving parts of the door.
The following explains how your Keyless Entry
can be used to OPEN, CLOSE, START, and
STOP your door.
Choose a convenient location that does not
interfere with the normal opening and closing
operation of the door, such as the door jamb.
Enter your 5-digit PIN (personal identification
number); door will begin to move
1.
CAUTION: The keypad
should be mounted a
minimum of 5 feet from
the floor to keep it out
of the reach of small
children.
Two screws are included
for proper mounting into
wood or other similar
material. If you're
mounting into some other
material, consult a
building contractor to
insure proper hardware is
used for a secure
NOTE: If you inadvertently enter an incorrect
code, the door will not move To Reset, press
and hold the "7/8" and "9/0" buttons for 2
seconds and reenter your PIN number.
NOTE: This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference when the equipment is operated in
a residential environment. This equipment generates,
uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the
instruction manual, may cause harmful interference to
radio communications. However, there is no guarantee
that interference will not occur in a particular
installation. If this equipment does cause harmful
interference to radio or television reception, which can
be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by
one or more of the following measures:
2. Unit remains active for next 25 sec.
Pressing any key, will stop the door if
opening, and stop or reverse the door if
closing.
Battery Replacement
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and
receiver.
- Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV
technician for help.
mounting.
Once you
Under normal operating conditions, the
battery should be changed once every 12
months. Dispose of used batteries
properly. To replace battery perform the
following steps:
have
determined
the
mounting
Your new Model 3966 Wireless Keyless Entry
contains a state-of-the-art wireless digital
transmitter capable of operating an unlimited
number of compatible garage door openers.
location,
use the
drilling
template
to
determine
hole
positions
and drill a
A. Snap open case with a coin and remove
old batteries.
For added security, your Wireless Keyless Entry
utilizes a "rolling code" technology that, each
time the transmitter communicates with the
receiver, sets a new code, selecting from
millions of combinations, reducing the possibility
of electronic equipment causing unwanted
access.
B. Replace batteries (two CR2032 or
equivalent) and snap case together.
Front Case
5/64" pilot
hole
Pre-drill a 5/64 pilot
hole 3/4" deep
For proper operation it is important that
you follow the programming directions
and sequence as written.
3/4" deep for the two mounting screws.
Snap open the Keyless Entry case with a coin.
Separate the front case from the back case.
Mount the back case and secure with screws
provided. Do not over tighten the screws as
this may bend or damage the back case. Install
and snap the front case onto the back case.
Remove paper backing from "Changing
Wayne-Dalton Corp.
One Door Drive n Mt. Hope, OH 44660
888-827-3667
Drilling Template
For Keyless Entry
(2) Coin Cells
Rear Case
Personal Identification Number" label and apply
label to a clean surface inside garage.
Batteries (CR2032)
Coin Slot
|