Installation
Instructions
Operation
Spray Change
Button
To change settings, from
either the full-body spray
or the concentrated power
spray, push the button
atthe base of the
showerhead so it extends
to the opposite side of its
current position. (It will
move horizontally to the
showerhead.)
Your new showerhead will fit a standard 1/2 ” shower arm. Do not
attach this product to a plastic shower arm since it may not
provide adequate support.
Tools are not required. Do not use pipe tape or any other
sealants when installing the showerhead. These materials are not
necessary and may cause the nut to loosen prematurely. Hand
tightening is sufficient to secure the shower thread. Make sure
the washer is in the end of the nut.
Spray Change
Button
1. Remove old showerhead. Clean pipe threads thoroughly.
Spray
Change
Button
2. Attach the flexible shower arm collar to the showerhead, being
careful to align the threads of the showerhead to the threads
of the flexible shower arm.
Care and Cleaning
Instructions
Shower
Arm Nut
Collar
Clean the filter screen at least once a year, or whenever you
notice a drop in water pressure. To remove, unscrew the nut
from the pipe. Remove screen by turning it counter-clockwise
(pliers may be used) and rinse. The white flow restrictor
beneath filter screen is also removable for cleaning. Tip the
nut and the flow restrictor will fall out. Flow restrictor must be
reinstalled with pointed end facing in. Reinstall filter screen
and rubber washer.
Flexible Arm
Spray
Change
Button
•
•
•
•
Cleaning is required when mineral deposits appear on the
Bracket
spray orifices to maintain proper working conditions.
Clean the flexible nozzles by rubbing with a finger or soft
bristled toothbrush.
Soaking and cleaning with household vinegar will help
remove mineral build up.
Do not clean or rinse any part with harsh chemicals, heavy
duty cleaners or abrasives. This may damage parts or
finish and may void warranty.
3. Straighten the flexible shower arm before trying to screw onto
the shower pipe. Again, take care in aligning the nut to the
shower pipe so you do not cross threads.
Adapter
4. While installing, support the shower
hold onto the nut rather than the co
Turn only the nut to tighten. Do not t
the flexible shower arm covering
5 foot hose
during installation. (This could
damage the covering and/or
Limited Lifetime
Warranty
Instruction Manual
cause the product to malfunction.)
Models CF-201(C), CF-261(C)
5. Tighten the shower nut onto the pip
securely by hand. Do not over tighte
or use pliers.
6. Slowly turn on cold water and check for leaks. If leaks occur,
re-tighten all connections.
7. Do not use excessive force in positioning the showerhead
and/or arm.
8. If the showerhead is not maintaining its position, re-tighten the
showered and shower arm nuts.
Water Pik, Inc. warrants to the original purchaser of this product
that it is free from defects in material and workmanship for as long
as the original purchaser owns the product. Water Pik will at our
election, replace any part of the product which in our opinion is
defective, provided that the product has not been abused,
misused, altered or damaged after purchase. (This includes
damage due to use of tools or harsh chemicals). In the event an
item qualifying for warranty action has been discontinued, we will
replace it with what we deem to be the closest available product.
Water Pik is not responsible for labour charges, installation or other
consequential costs. The responsibility of Water Pik shall not
exceed the original purchase price of the product. Save your
receipt as proof of purchase is required for warranty action.
Flow Control
Filter Screen
Washer
Flow Regulator
with O-ring
(black O-ring
faces out)
9.5L per minute maximum
flow is limited by the flow
restrictor. For low water
pressure areas, flow
restrictor may be removed.
To remove, unscrew filter
screen by turning counter-
clockwise. Tip pivot ball
assembly and flow control
will fall out for cleaning or
removal.
Showerhead
Nut
Hand-Held
Installation
1. Remove old showerhead. Clean pipe threads thoroughly.
2. Slightly loosen swivel collar on bracket.
3. Hand tighten pivot ball to pipe.
4. Hand tighten adaptor to showerhead.
5. Hand tighten hose to adapter and bracket.
6. Place showerhead in bracket.
This product is covered by one or more of the following patents. U.S.: 4,674,687;
5,316,216; 5,449,206(Lic); 5,865,378; 5,997,047(Lic); 6,164,569; 6,164,570; 6,230,989;
6,454,186; 6,626,210; 6,629,651; 6,641,057; 6,739,523; 6,758,826; 7,066,411B2;
7,111,798B2; 7,144,666B2; D406,636; D415,247; D418,902; D418,903; D422,053;
D422,336; D427,661; D440,641; D450,805; D450,806; D450,807; D451,169; D451,170;
D451,171; D451,172; D451,583; D451,980; D452,553; D452,725; D452,897; D453,370;
D453,551; D457,937; D485,887; D490,498; D527,440S; D528,631S; D529,151S;
D533,253S; D577,099S; D577,793S; D581,014S; D590,048S; Canadian: 94868; 94871;
96859; 96860; 96861; 96862; 96863; 96864; 96865; 96866; 96867; 96891; 96892;
96893; 96894; 96895; 96896; 2,277,060; Mexico: 15037; 186852; 218192;
Germany: 40105034.3; 40502480; M9706460.2; U.K.: 3,021,116; 3,021,863; 3,021,864;
E.U.: 000341706-0001; 000341706-0002; 000341706-0003; France: 013345;
Switzerland: 128049; China: ZL98802624.4; 93120174.8; ZL200530004083.3;
Hong Kong: 1003339; South Korea: 389207; Australia: 726023; Singapore: 44333;
Japan: 1230114; Additional: 00601962 (Belgium, Switzerland, Germany, France, United
Kingdom, Italy, Luxembourg, The Netherlands).
Filter
Screen
Flow Regulator
Cascadia® is a trademark of Water Pik, Inc. registered in Canada, EU, Switzerland, and the
United States.
Waterpik® is a trademark of Water Pik, Inc. registered in Argentina, Australia, Austria, Canada,
China, Czech Republic, Hungary, India, Japan, Poland, Russian Federation, South Africa,
Switzerland, Ukraine, and the United States.
Waterpik® (stylized) is a trademark of Water Pik, Inc. registered in Canada, EU, Mexico,
Switzerland, and the United States.
© 2009 Water Pik, Inc.
Have any questions or need assistance?
Call our toll-free Customer Service Line:
Water Pik, Inc.
Printed in China
888-226-3042
8:00 a.m. to 4:00 p.m. MT, Monday-Friday
FN 20007766-F AB
Showerhead made in China
DATE: 27 May 2009
CLIENT: Water Pik, Inc.
FILENAME: FN20007766-F_AB_CascadiaInst.indd
FILE TYPE: Adobe InDesign CS4
SIZE FLAT: 8-1/2” x 8-1/2”
DESCRIPTION: Cascadia Showerhead Instruction Manual - Canada
PREPARED BY: Brian Colon
SIZE FOLDED: 3-5/8” x 4-1/4”
INK: Black
FORM: 20007766-F AB
FOLDS: Vertical trifold, Horiz bifold
DIELINE: N/A
NOTES:
|