Quick Start
Quick Reference Setup Guide
CLUB-8000
This quick reference guide is provided to help you set up your
CLUB-8000 system for the first time. It contains instructions
on setting up the products that are included in the CLUB-
8000. If you are connecting any additional gear that is not
included in the CLUB-8000, refer to the appropriate manuals
for detailed instructions.
Gathering Package Contents
The first step to putting together your new CLUB-8000 system is unpacking all of the necessary equipment. Remem-
ber to keep your manuals nearby when setting up, as you may need to reference them. The products listed below are
included in the CLUB-8000 system:
CDG-9000 PRO
VSP-M1 Multi-Effect Digital Signal Processor/Mixer
• 1 Control interface connector wire
• [1] Instruction Manual
• 1 Instruction manual
SS-88 Speaker Stands
• [4] SS-88 speaker stands
KJM-8000+ 9-Channel Digital Key Control KJ/DJ Mixer
• [1] Instruction Manual
CLUB-8 Road Case
• [1] CLUB-8 road case
• [1] Rolling cart
VP-2100 PRO 2000W Professional Power Amplifier
• [1] Instruction Manual
• [2] MK-38 PRO microphones
• [1] Gooseneck DJ light
• 1 RCA to 1/4” Patch Cable (3.3 ft paired)
• Rack-mounting screws
VX-15 Vocal Speakers
• [4] VX-15 speakers
Mounting components into the CLUB-8
Below is one way to configure your CLUB-8000:
Follow these basic guidelines when mounting:
• Always screw in the mounting screws using an “X” forma-
tion.
• If possible, to keep the products cooler, leave some space in
between the components in the rack.
1
3
4
CDG-9000 PRO CONTROLLER
KJM-8000+ MIXER
2
CDG-9000 PRO PLAYER
VP-2100 PRO AMPLIFIER
On the web at www.vocopro.com
or call toll free 1-800-678-5348
CDG-9000 PRO player unit to KJM-8000+
2
You have the option of either connecting each deck of the CDG-9000 PRO separately (Fig. 1) or together through a single
SWITCHED output (Fig. 2).
Separately through individual deck outputs (Fig.1)
Using RCA cables:
1. For each deck, connect the L/R (red & white) audio outputs and Video (yellow) output on the CDG-9000 PRO to the
CDG(1) and DVD(3) inputs on the rear panel of the KJM-8000+
CDG-9000 PRO Player
CDG(1)
DVD(2)
CDG(1)
DVD(2)
KJM-8000+ Mixer
LD(3)
LD(3)
Together through SWITCHED output (Fig. 2)
CDG-9000 PRO Player
Using RCA cables:
1. Connect the L/R SWITCHED audio and
SWITCHED video outputs on the CDG-9000
PRO player to the CDG(1) audio input on the
KJM-8000 PRO
CDG(1)
DVD(2)
KJM-8000+ Mixer
LD(3)
KJM-8000+ to VP-2100 PRO
3
You can do this using either XLR(f) to XLR(m) cables or XLR(f) to ¼”(m) cables. Below are instructions for each.
Using two XLR(f) to XLR(m) (Fig.1)
Using two XLR(f) to ¼”(m) (Fig. 2)
1. Connect the XLR(f) end to the LEFT MASTER AUDIO
XLR output on the KJM-8000+ and the XLR (m) end to
the left XLR audio input on the VP-2100 PRO.
2. Now do the same thing except now go from the RIGHT
MASTER AUDIO XLR output on the KJM-8000+ and the
right XLR audio input on the VP-2100 PRO
1. Connect the XLR(f) end to the LEFT MASTER AUDIO XLR
output on the KJM-8000+ and the ¼”(m) end to the CH. B
¼” audio input on the VP-2100 PRO.
2. Now do the same thing except now go from the RIGHT
MASTER AUDIO XLR output on the KJM-8000+ and the CH.
A ¼” audio input on the VP-2100 PRO.
-BRIDGE+
-BRIDGE+
CH
2
CH
1
CH
2
CH
1
STEREO
50Hz ON
VP-2100 PRO Amplifier
STEREO
50Hz ON
THROUGH
THROUGH
THROUGH
THROUGH
MONO
BRIDGE
30Hz OFF
MONO
BRIDGE
30Hz OFF
LOW CUT
FILTER/
LOW CUT
FILTER/
MODEL
VP-2100PRO
MODEL
VP-2100PRO
SPEAKER OUTPUTS
BALANCED INPUTS
SPEAKER OUTPUTS
BALANCED INPUTS
CDG(1)
DVD(2)
CDG(1)
DVD(2)
KJM-8000+ Mixer
LD(3)
LD(3)
VP-2100 PRO to VX-15 speakers
4
VP-2100 PRO Amplifier
Speakers 1 and 2
-BRIDGE+
CH
2
CH
1
Using the SPEAKON style to ¼” adapter and ¼”(m) to
¼”(m) cable (included):
STEREO
50Hz ON
THROUGH
THROUGH
MONO
BRIDGE
30Hz OFF
LOW CUT
FILTER/
1. Connect the SPEAKON style end to CH.1 on the rear
panel of the VP-2100 PRO
MODEL
VP-2100PRO
SPEAKER OUTPUTS
BALANCED INPUTS
2. Connect one end of the ¼” cable to the ¼” end of the
adapter
3. Connect the other end of the ¼” cable to one of the
four VX-15’s.
3. Repeat this for the second speaker, except now connect
the SPEAKON style end to CH. 2 on the VP-2100 PRO and
the ¼” end to the second VX-15 speaker.
Speakers 3 and 4
VX-15 Speaker #1
VX-15 Speaker #2
Using a ¼”(m) to ¼”(m) cable
VX-15 Speaker #3
VX-15 Speaker #4
1. Connect one end of the ¼” cable to the open ¼” jack
on the rear of speaker 1
2. Connect the other ¼” end to the back of the 3rd
speaker.
3. Repeat this for the final speaker now going from the
back of speaker 2 and into the 4th speaker.
Connecting Microphones to the KJM-8000+
5
Using either a mic cable with two XLR ends (Fig. A) or an XLR to ¼” cable (Fig. B):
Connect the microphone cables to the MIC inputs on the rear panel of the KJM-8000+.
CDG(1)
DVD(2)
CDG(1)
DVD(2)
LD(3)
KJM-8000+ Mixer
LD(3)
Adding the VSP-M1 to the CLUB-8000 system
6
Using either a mic cable with two XLR ends or an XLR to ¼” cable:
1. Connect the XLR(f) end to the LEFT BALANCED OUTPUT on the rear panel of the VSP-M1.
2. Connect the XLR(m) or ¼” end to MIC input 1 on the rear panel of the KJM-8000+.
3. Follow the above steps, now going from the RIGHT BALANCED OUTPUT on the VSP-M1 to MIC input 2 on the rear panel
of the KJM-8000+.
4. Connect the mics to the mic inputs on the rear panel of the VSP-M1.
VSP-M1 Processor
CDG(1)
DVD(2)
KJM-8000 PRO Mixer
LD(3)
|