USER OPERATING MANUAL
Colour Monitor
TV14
TV21
TV28
Please read this User Operating Manual before using your Colour Monitor
Pre p a ra tio n-Ma ins Sup p ly ●
ANT.75
Pre p a ra tio n-AV Co nne c tio n ●
Insta lla tion
Mains Supply
☞ Connect the power cord of the monitor to a wall outlet.
✐ The monitor is prepared for a mains voltage AC220~240V
50Hz. When the monitor is not to be used for an extended
period of time, it is advisable to disconnect the power cord
from the power outlet.
AC Mains Outlet
WARNING!
High voltages are used in the operation of this set.
Refer service to qualified service personnel.
Important:
This equipment is fitted with an approved non rewireable UK The wires in this mains lead are coloured in accordance with
mains plug.
the following code:
To change a fuse in this type of plug proceed as follows:
Blue ------->
Brown ---->
Neutral
Live
1. Remove the fuse cover and fuse.
2. Fix a new fuse which should be a BS1362 5Amp A.S.T.A.
or BSI approved type.
1. The Blue wire must be connected to the terminal which is
marked with the letter “N” or coloured BLACK.
2. The Brown wire must be connected to the terminal with
the letter “L” or coloured RED.
3. Refit the fuse cover.
If the fitted plug is not suitable for your socket outlets, it
should be cut off and an appropriate plug fitted in its place. If 3. Do not
connect either wire to the earth terminal in the
the mains plug contains a fuse, this should have a rating of
5Amp. If a plug without a fuse is used, the fuse at the
distribution board should not be greater than 5Amp.
plug which is marked with the letter “E” or by the earth
symbol or coloured GREEN or GREEN and YELLOW.
Before replacing the plug cover, make certain that the cord
grip is clamped over the sheath of the lead - not simply over
Note: The severed plug must be destroyed to avoid a
possible shock hazard should it be inserted into a 13Amp the wires.
socket elsewhere.
AV Connection
VIDEO IN
AUDIO OUT AUDIO IN VIDEO OUT
Terminal
Description
VIDEO IN
VIDEO OUT
AUDIO IN
BNC connector for video in.
BNC connector for video out.
RCA connector for audio in.
RCA connector for audio out.
AUDIO OUT
3
● Mo nito r Co ntro ls
● Switc hing On/ Off
Ge ne ra l Ope ra tion
Controls
-
Le ve l d o wn
Le ve l up
P▲
Pic ture c o ntro l
Po we r Ind ic a to r
Ma ins On/ Off switc h
F/ M No o p e ra tio n
No o p e ra tio n
PT
P▼ No o p e ra tio n
Switching On/Off
To turn the monitor on, press the Mains On/Off button
.
✐The power indicator illuminates red to show the power is on.
To switch the monitor off press the Mains On/Off button
again.
Be sure to set the Mains On/Off button to the
Off position if a power failure occurs.
If you find the power indicator flashing, turn off
the monitor immediately. The flashing indicator is
a warning to show that the power protection
feature is operating. The fault may be cleared by
switching the monitor off and on again after the
indicator has completely dimmed (about 5
Power Indicator
seconds). If the indicator flashes again switch off
the monitor and contact the service department.
4
So und a nd Pic ture Co ntro ls ●
☞
Ge ne ra l Ope ra tion
Sound and Picture Controls
■ Sound Volume Control
SOUND +30
IIIII|||||---------
To increase the sound volume level, press the
b utton.
-
To decrease the sound volume level, press the
b utton.
■ Selection & Adjustment of Controls
SOUND +10
II----------------
SOUND +45
IIIII|||||||||||||--
The following controls can be selected by using the P▲ b utton
-
and adjusted using the
or
b utton.
-
COLOUR : To adjust the picture colour.
BRIGHT : To adjust the picture brightness.
CONTRAST : To adjust the picture contrast.
P
▲
SHARPNESS : To adjust the picture sharpness.
CHILD LOCK : To lock the monitor control buttons.
(see page 6)
COLOUR
CHILD LOCK
Press the P▲ button repeatedly to select the control you
wish to adjust.
IIIII------------
NO/YES
1
2
The control display changes as illustrated.
Press the
press the
b utton to increase the control level, or
-
b utton to decrease the control level.
SHARPNESS
IIIII------------
BRIGHT
IIIII------------
All new values are automatically stored in the memory.
CONTRAST
IIIII------------
5
● Child Lock
Ge ne ra l Ope ra tion
Child Lock
This monitor has a child lock function which renders the buttons
on the front of the monitor inoperative.
P
▲
CHILD LOCK
NO/YES
Setting the Child Lock Mode
Press the P▲ b utton repeatedly until the word "CHILD LOCK”
appears on the screen.
Press the
button until the word "YES" turns yellow, the
operation of the control button is now locked.
CHILD LOCK
NO/YES
Note: The child lock function will be cancelled when the
Monitor is switched off by pressing the Ma ins ON/ OFF
b utton.
6
Spe c ific a tion
Monitor Specification
Common Specification
AC 220~240V 50Hz
15.625KHz / 50Hz
300 TVL (BNC)
PAL
Power source
Scanning frequency
Resolution
Colour system
Input terminals
Video IN
BNC connector
RCA connector
Audio In
Output terminals
Video OUT
BNC connector
RCA connector
Audio OUT
TV14
TV21
TV28
Sound output (watts)
1.5
2
3
Picture tube,Diagonal-cm (Deflection) 37, (90°)
55, (90°)
70, (110°)
66
628 x 567 x 469
30.4
(Visible picture diagonal) (cm)
Dimensions (W x H x D mm )
Weight (kg)
34
51
370 x 335 x 391.5
9.0
521 x 465 x 481
19.0
7
Norbain House
Eskdale Road
Winnersh Triangle
Wokingham
Berkshire
RG41 5TS
Part No. SKP10126 E7CV
|