VF05
IMPORTANT SAFETY INSTRUCTIONS
CAUTION:
• TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
DISMANTLE. THERE ARE NO SERVICEABLE PARTS INSIDE.
• TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS UNIT TO RAIN OR MOISTURE.
WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR
PERSONAL INJURY:
• Turn off/unplug and allow to cool before replacing bulb or cleaning.
•
Light bulbs get HOT quickly! Do not touch the bulb while the lamp is on.
• Do not operate the lamp in close proximity to flammable or
combustible vapors, such as aerosol (spray) products or where
oxygen is being administered.
• Use only the type of bulb and maximum wattage indicated by the
manufacturer.
• Never cover the lamp when it is in operation.
• Read these instructions – before using this lamp.
• Keep these instructions – for future reference.
• Do not use this lamp in damp/humid or wet locations.
• For indoor use only.
• Clean only with dry cloth.
• Do not defeat the safety purpose of the polarized plug. A polarized
plug has two blades with one wider than the other. If the provided
plug does not fit in your outlet, consult an electrician for replacement
of the obsolete outlet.
• Protect the power cord from being walked on or pinched particularly
at plugs, convenience receptacles, and the point where it exits from
the lamp.
• Unplug this lamp during lightning storms or when unused for long
periods of time.
• If the lamp has been damaged in any way, such as power-supply
cord or plug is damaged, liquid has been spilled or objects have
fallen onto the lamp, the lamp has been exposed to rain or moisture,
does not operate normally, or has been dropped, it should not be
operated. There are no user serviceable parts within this lamp.
SAVE THESE INSTRUCTIONS
2
ASSEMBLY INSTRUCTIONS
Before assembling, please review all instructions.
1. Carefully lay out all parts on flat surface as shown in illustration.
2. Screw post (B) into the base (A) and hand tighten.
3. Screw post section (C) into post (B) and hand tighten.
4. Screw body (F) into post (C) and hand tighten.
5. Rotate shade (H) to right angle with body (F) and parallel to the
floor. Then, use the (included) allen wrench (G) to carefully tighten
the screw.
6. Loosen the thumbscrew (E) to adjust the lamp height. Raise or
lower the lamp body (F) to the desired height and tighten the
thumbscrew (E).
7. Remove the 27 W Natural Spectrum® bulb from the packaging and
carefully insert it into the socket as demonstrated in Figure 1. Be
sure to hold the bulb by the base and ensure it is fully inserted into
the socket and clipped into the metal clip (I).
8. Note the telephone number on the bulb provides contact information
when reordering.
9. Plug lamp into an appropriate outlet and turn on the switch.
10. Do not use with an extension cord or on a circuit with a dimmer
switch.
11. Save the packaging in case you need to send the lamp to Verilux for
servicing.
3
ASSEMBLY INSTRUCTIONS
4
GENERAL PRECAUTIONS
• Do not use with power supply voltage other than 120V AC
• Avoid placing the lamp in areas that are dusty, humid/moist, lack
ventilation, or are subject to constant vibration.
• Not for use with light dimmers, timers, motion detectors, voltage
transformers, or extension cords.
• Do NOT use lubricating agent in bulb assembly.
• The light bulb may become loose during transit. To reinstall the light
bulb, see the bulb installation instructions on page 3.
• Close supervision is recommended when this lamp is used by or
near children, or others who may not understand the need for these
precautions. Do not leave the lamp unattended during use.
This product may cause interference with radios, cordless
telephones, or devices that use a wireless remote control,
such as televisions.
This lamp has been tested and found to comply with Part 18 of the
FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This lamp
generates, uses, and can radiate radio frequency energy and, if
not used in accordance with the instructions, may cause harmful
interference to radio communications. If interference occurs try to
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the lamp and receiver.
• Connect the lamp into an outlet on a circuit different from that to
which the receiver is connected.
• Move the lamp out of the line of sight of the remote control receiver.
• Consult the dealer or an experienced radio/TV technician for help.
Note: This product may cause interference to radio equipment
and should not be installed near maritime safety communications
equipment or other critical navigation or communication equipment
operating between 0.45-30 MHz.
5
TROUBLESHOOTING
Before requesting service on your Verilux® lamp please read the
following:
• Make sure all power connectors, cords, and plugs are inserted fully
and securely.
• Make sure there is power to the wall outlet or try another outlet – not
connected to a dimmer.
CARE & CLEANING
Your Verilux® lamp is made from high quality materials that will last for
many years with a minimum of care.
Clean only with a soft dry cloth – DO NOT USE SOLVENTS OR
CLEANERS CONTAINING ABRASIVES OR AMMONIA
WARNING: To prevent risk of shock or personal injury
when cleaning lamp, make sure you have turned off and
unplugged the lamp, and allow sufficient time for the bulb
to cool.
6
|