VEC128SL_ManualEN_092605 9/26/05 9:20 AM Page 1
VEC128SL
®
SPORT SPOT LANTERN COMBO
CORDLESS • RECHARGEABLE
o
PATENT N D432,692
AND OTHER PATENTS PENDING
USER'S MANUAL &
WARRANTY INFORMATION
IMPORTANT SAFETY INFORMATION, SAVE THESE INSTRUCTIONS
TO REDUCE THE RISK OF INJURY, USER MUST READ AND UNDERSTAND
THIS INSTRUCTIONAL MANUAL. THIS MANUAL CONTAINS IMPORTANT
INFORMATION REGARDING THE OPERATION AND WARRANTY OF THIS
PRODUCT. PLEASE RETAIN FOR FUTURE REFERENCE.
4140 S.W. 30th Ave., Ft. Lauderdale, FL 33312
Toll Free: (866) 584-5504
© 2005 VECTOR MANUFACTURING
4140 SW 30TH AVE.
FT. LAUDERDALE, FL 33312
www.vectormfg.com
VEC128SL_ManualEN_092605 9/26/05 9:20 AM Page 5
9.1 BATTERY REMOVAL PROCEDURE
CAUTIONS:
• DO NOT SUBMERGE IN WATER.
• Do not recharge with other than supplied AC and
DC Recharge Adapters
• Do not overcharge battery
• Do not operate lights while recharging—this can cause damage
to the unit or charger
• This spotlight produces high levels of heat when
operating—DO NOT TOUCH THE SPOTLIGHT LENS
WHEN THE SPOTLIGHT IS ON
• Keep spotlight lens away from combustible materials when
spotlight is On
• This light is not a toy—keep away from children
1. Press the tab on the lower part of the Battery Compartment Cover while
lifting the cover.
2. Fully remove the cover and set it aside.
3. Carefully move the battery towards the opening of the compartment.
4. Using a long nose pliers, carefully rock each spade terminal and remove
them from the Battery Spade Lug Terminals. Note the colors of the attached
wires and to which terminal they were connected.
5. Fully remove the battery and set it aside.
6. Follow Safe Battery Disposal instructions.
9.2 BATTERY INSTALLATION PROCEDURE
1. Partially insert the new battery in the compartment in the same position as the
old battery.
2. Using long nose pliers, attach the Spade Connectors to their respective
Battery Spade Terminals. Check to ensure they are fully connected.
3. Push battery back into compartment.
4. Replace cover and slide downward until the tab snaps into place.
5. Momentarily check operation of the spotlight and lantern for proper operation.
6. Recharge the battery using either the AC or DC Recharge Adapter.
CONTENTS
1.
2.
3.
4.
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
10. SAFE BATTERY DISPOSAL
Contains a maintenance-free, sealed, non-spillable, lead acid battery. This battery
is fully recyclable and should be accepted at any location that accepts common
automotive starter batteries. County or municipal recycling drop-off centers, scrap
metal dealers and retailers who sell automotive replacement lead acid starter
batteries. For more information on recycling this battery, call toll-free (877) 288-
7722
RECHARGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
4.1 AC Recharge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
4.2 DC Recharge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
5.
6.
MAINTENANCE/PARTS REPLACEMENT . . . . . . . . . . . . . . . .3
BATTERY DISPOSAL WARNINGS
• Do not dispose of the battery in fire as this may result in an explosion
• Before disposing the battery, protect exposed terminals with heavy-duty
electrical tape to prevent shorting (shorting can result in injury or fire)
• Do not expose battery to fire or intense heat as it may explode
SPOTLIGHT BULB REPLACEMENT . . . . . . . . . . . . . . . . . . . . .3
6.1 SPOTLIGHT Bulb Removal . . . . . . . . . . . . . . . . . . . . . . .4
6.2 Spotlight Bulb Installation . . . . . . . . . . . . . . . . . . . . . . . .4
7.
LANTERN TUBE REPLACEMENT . . . . . . . . . . . . . . . . . . . . . .5
7.1 Fluorescent Tube Removal . . . . . . . . . . . . . . . . . . . . . . .5
7.2 Fluorescent Tube Installation . . . . . . . . . . . . . . . . . . . . . .6
11. SPECIFICATIONS
Spotlight Bulb
Lantern Tube
Battery
H-3 Series, 6 volt, proprietary
13 Watt, Twin U Tube Fluorescent, proprietary
Maintenance free, sealed lead acid 6 volt, 6 Amp Hour
.5 Ampere
8.
9.
FUSE REPLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
BATTERY REPLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . .6
9.1 Battery Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
9.2 Battery Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Fuse
10.
11.
SAFE BATTERY DISPOSAL . . . . . . . . . . . . . . . . . . . . . . . . . .7
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
WARRANTIES
7
VEC128SL_ManualEN_092605 9/26/05 9:20 AM Page 7
7.2. FLUORESCENT TUBE INSTALLATION
1. INTRODUCTION
1. Make sure that the Lantern Switch is Off.
Congratulations on purchasing the Vector Sport Spot Lantern, an advanced design
combination spotlight and lantern. It instantly converts use from a powerful spotlight
to a soft, long-lasting area light. See Figure 1A and 1B. It uses a powerful
proven-technology, rechargeable, sealed lead acid battery that allows for years of
dependable use, recharge after recharge. It was designed from the ground up to
be the most versatile and practical light for travel, camping, picnicking, tailgate
parties and boating. The Sport Spot Lantern gives you the kind of light you need,
when and where you need it.
2. Press the new fluorescent tube’s base into the Tube Socket Assembly.
3. Replace the Tube Socket Assembly so that the two Support Rods pass
through the assembly and it is fully seated against the clear plastic dome.
4. Replace the two nuts and tighten (clockwise) so that the tube assembly is snug.
5. Screw on (clockwise) the End Cap until it is snug.
6. Test the fluorescent tube for proper operation by reconnecting the battery
and turning On the Lantern switch.
8. FUSE REPLACEMENT
FIGURE 1A
FIGURE 1B
The fuse is located inside the DC plug. (See Figure 5 for fuse replacement.)
Make sure the DC Recharge connector is disconnected from the Sport Spot Lantern.
FIGURE 5
FLANGE
CONTACT
SPRING
PLUG
°
FUSE
FUSE REPLACEMENT PROCEDURE
SPOTLIGHT ON/OFF
LANTERN SWITCH
1. Unscrew (counterclockwise) the flange from the DC plug.
2. Remove the flange, contact and fuse from the plug assembly.
3. Replace fuse with a .5 amp fuse of same type and size.
4. Place the center contact in the flange.
5. Replace the center contact and flange on the DC plug.
6. Tighten (clockwise) until the flange is fully seated.
DO NOT OVERTIGHTEN FLANGE!
RECHARGE LEDS
9. BATTERY REPLACEMENT
The battery is contained in a compartment in the base of the unit. A plate must be
removed to gain access to the battery. Figures 5A and 5B show access to the
battery compartment.
Two recharge adapters are supplied with the Sport Spot Lantern. It is rechargeable
from either a DC cigarette lighter type 12 volt DC socket (accessory socket) or from
any 120 volt 60 Hz AC receptacle. 12 volt DC power is available from most
vehicles, boats, jump starters and portable battery packs. Vector has a variety of
portable power products that may be considered as companions to your Sport Spot
Lantern. Contact Vector for additional information.
FIGURE 5A
FIGURE 5B
BATTERY
COMPARTMENT
COVER
SWITCH
TAB
AC/DC
RECHARGE
BARREL
SPADE
CONNECTOR
RECEPTACLE
SPADE
LUG
TERMINALS
SPADE CONNECTOR
BATTERY
1
6
VEC128SL_ManualEN_092605 9/26/05 9:20 AM Page 9
7. LANTERN TUBE REPLACEMENT
2. FEATURES
• 1,000,000 Power Series Spotlight
™
The Lantern fluorescent tube is mounted on a socket assembly. Power is sent to the
tube socket through the two support rods. It is very important to make sure the
Lantern switch is turned OFF before removing the end cap. If there are any doubts
about the ON/OFF switch being Off, then refer to the Battery Removal section and
disconnect the battery before removing the end cap.
• Powerful replaceable H-3 Series 6 volt quartz halogen bulb in spotlight
• Powerful replaceable 13 watt fluorescent U-shaped twin tube in lantern
• Head swivels 90 degrees for soft, 360 degree area lighting
• Rubber safety guard protects spotlight
• Recharging LED and battery FULL LED
WARNING:
• Recharges from standard North American Standard 120 volt AC,
60 Hz, receptacle
FLUORESCENT TUBES OPERATE WITH HIGH VOLTAGE.
DO NOT REMOVE END CAP UNLESS POWER IS OFF
AND THE BATTERY IS DISCONNECTED. SEE SECTION 9
• Recharges from 12 volt DC accessory socket
• Three way switch - Spotlight, Off and Lantern
• Comfortable handgrip
See Figure 4 for Fluorescent Tube Replacement
• Stable base prevents tip over in any head position
4
FIGURE 4
3
5
NOTE:
1
2
This unit is shipped in a partially charged state. Charge unit using either
AC or DC method until the green LED lights. Charge after each use. Initial
charge should be for 12 hours.
3. OPERATION
6
The swivel action of the unit keeps the lamp head securely in position for use while
carrying or while on tabletop. The range of swivel motion is greater than 90
degrees with five locking positions. The spotlight position (upright) focuses light
straight ahead. The lantern position (spotlight tilted forward 90 degrees) floods
light in a 360-degree pattern for reading, cooking and many other uses. A
three-position Power Switch (Spotlight, Off, Lantern) controls on/off operation of
both lights. The switch is protected by a flexible covering that protects it from dust,
dirt and moisture. This ensures reliability and extends the life of the switch. The
spotlight can be continuously lit for up to 20 minutes on a full battery charge; the
lantern can be lit for up to four hours on a full battery charge.
1. DOME
2. TWIN TUBE FLUORESCENT
3. TUBE SOCKET ASSEMBLY
4. NUTS
5. END CAP
6. SUPPORT RODS
4. RECHARGE
7.1 FLUORESCENT TUBE REMOVAL
All batteries lose charge over time, especially when they are warm. Frequent
battery recharges will extend battery life. AC recharge is recommended every two
months, when not in frequent use. Use the AC recharge adapter and charge until
battery is full. AC and DC recharge connections are through a heavy-duty barrel
receptacle at the lower rear of the unit. (See figure 5A) Two LED indicators display
the status of recharge. Continue recharge operation until the two LEDS are equally
bright. (See Figure 1A.)
1. Make sure that the Power Switch is Off AND the battery is disconnected.
2. Remove the set screw from the end cap - item #5.
3. Rest the unit on a secure tabletop.
4. Position the head to be in the Spotlight position.
5. Unscrew (counter clockwise) the End Cap and set aside.
6. Unscrew (counter clockwise) the two nuts from the two support rods and set
them aside.
7. Slide the Tube Socket assembly away from the head and remove it from
the two support rods.
8. Set it on a stable work surface like a table, bench,etc.
9. Grasp the Tube Socket and push on the fluorescent tube base to disconnect
the tube from the socket.
10. Do not allow the tube to drop.
11. Follow local procedures for safe fluorescent tube disposal.
5
2
VEC128SL_ManualEN_092605 9/26/05 9:20 AM Page 11
AC AND DC RECHARGE ADAPTERS
SPOTLIGHT BULB REMOVAL/INSTALLATION
FIGURE 3
4
5
6
3
FIGURE 2A
FIGURE 2B
2
DC RECHARGE
AC RECHARGE
ADAPTER
ADAPTER
7
FUSED DC PLUG
1
8
1. SAFETY RING
2. RETAINING RING TAB
3. RETAINING RING LENS
5. LOE-NRISNG
BARREL CONNECTOR
9
10
4.
11
6. REFLECTOR/LAMP ASSEMBLY
7. NOTCH
4.1 AC RECHARGE
9
8. RETAINING WIRES
9. WHITE WIRE
The AC Recharge adapter provides 300 mA DC for recharging the
batteries. Power the AC Recharger from a standard, 120 volt, 60 Hz AC North
American receptacle. The AC recharger will not support lamp operation. Do not
operate the lamps while the AC Recharger is connected to the Recharge Port.
Charge with lamps Off until LEDs are equally bright. This steady recharge will
prolong battery life. Only use the supplied AC Recharger—DO NOT SUBSTITUTE
WITH ANOTHER. (SEE FIGURE 2A)
10
10. GREEN OR BLACK WIRE
11. SCREW
11
6.1 SPOTLIGHT BULB REMOVAL PROCEDURE
1. Make sure that the Power Switch is Off AND the
battery is disconnected.
2. Rest the unit on a secure tabletop.
4.2 DC RECHARGE DC
3. Position the head to be in the Spotlight position.
4. Lift off the rubber Safety Ring and set it aside.
The Recharge adapter provides DC for recharging the batteries.
Power the DC Recharger from a standard, 12 volt DC cigarette lighter type
accessory socket. Charge until LEDs are equally bright. Only use the supplied
DC Recharger - do not substitute with another. The DC Recharge Adapter’s DC Plug
is equipped with a user-replaceable 10-ampere fuse. (SEE FIGURE 2B)
5. Grasp the Retaining Ring and rotate it slightly clockwise until the
ring’s tab lines up with the notch in the head.
6. Lift off the retaining ring.
7. Pull the lens, “O” ring and reflector assembly from the head.
8. Set the lens and “O” ring aside.
9. The Reflector/Lamp Assembly should be hanging from the two wires.
10. On the Reflector Assembly, carefully squeeze the two retaining wires
together and lift them to release them from the “T” slot.
11. Loosen the screw—item #11.
5. MAINTENANCE/PARTS REPLACEMENT
If the unit has dirt on it, gently clean the outer surfaces of the Sport Spot Lantern
with a soft cloth moistened with a mild solution of water and detergent. Periodically
inspect the condition of recharge adapters, connectors and wires. Replace any
components that may have become worn or broken.
12. Rotate the two retaining wires upward as shown, to allow the bulb to lift out.
13. Disconnect the white wire by pulling apart the two connectors on the wire.
14. Follow local procedures for bulb disposal.
Four parts are replaceable by users. The quartz halogen bulb and the fluorescent
tube are proprietary and are only available through Vector Manufacturing. The sealed
lead acid battery and fuse are available from Vector as well as from popular
automotive parts suppliers nationwide. Contact Technical Support for replacement parts
and any additional information that you may need at (866) 584-5504.
6.2 SPOTLIGHT BULB INSTALLATION PROCEDURE
1. Insert the new bulb in the Reflector/Lamp Assembly.
2. Rotate the two retaining wires downward as shown, to hold the bulb in place.
3. Tighten the screw— item #11.
4. Connect the white wire by pushing together the two connectors.
5. On the reflector Assembly, carefully squeeze the two retaining wires together
and place them in the “T” slot.
6. Replace the Reflector/Lamp Assembly, “O” Ring and Lens.
7. Place the Retaining Ring so that it’s tabs are aligned with the notches in the head.
8. Press the Retaining Ring until it is fully seated and rotate it slightly counter clock–
wise to secure it against the head.
9. Replace the rubber Safety Ring by pushing it onto the Retaining Ring. Make
sure the Safety Ring is fully seated.
10. Check the spotlight operation by reconnecting the battery and turning on
the switch.
6. SPOTLIGHT BULB REPLACEMENT
See Figure 3 for bulb removal and replacement.
WARNING:
DO NOT ATTEMPT SPOTLIGHT BULB REPLACEMENT UNLESS POWER IS
OFF AND THE BATTERY IS DISCONNECTED. SEE SECTION 9.
3
4
|