User’s manual
IS7101
DECT 6.0 accessory handset
for use with VTech models
IS7121/IS7121-2/IS7121-22
Congratulations
on purchasing your new VTech product. Before using this telephone, please read
Important safety instructions on page 5 of this manual.
This manual has instructions how to set up and register your new handset. For
complete instructions on using the handset, see the Abridged user’s manual that
came with your telephone base.
You may also view or download the online Complete user’s manual for a
Compatible with
Hearing Aid T-Coil
Telephones identified with this logo have reduced noise and
interference when used with most T-coil equipped hearing
aids and cochlear implants. The TIA-ꢀ083 Compliant Logo is
a trademark of the Telecommunications Industry Association.
Used under license.
T
TIA-1083
The ENERGY STAR® program (www.energystar.gov)
recognizes and encourages the use of products that save
energy and help protect our environment. We are proud to
mark this product with the ENERGY STAR® label indicating it
meets the latest energy efficiency guidelines.
Register online to get an additional 3-month warranty!
Registration
Register your product online for enhanced
warranty support.
Product news
Learn about the latest VTech products.
BC
ꢀ
Battery charging
Once you have installed the battery, the screen indicates the battery status (see
the table below). For best performance, keep the handset in the telephone base
when not in use. The battery is fully charged after ꢀ3 hours of continuous charging.
Battery indicators
Battery status
Action
The screen is blank, or
displays Place in charger little charge. The handset
and flashes.
The battery has no or very
Charge without interruption
(at least 30 minutes).
cannot be used.
The screen displays
Low battery and flashes.
The battery has enough
charge to be used for a
short time.
Charge without interruption
(about 30 minutes).
The screen displays
HANDSET X.
The battery is charged.
To keep the battery charged,
place it in the telephone base
or charger when not in use.
If you place the handset in the telephone base or charger without plugging in the
battery, the screen displays No battery.
Add and register a handset
You can add new handsets (purchased separately) to your telephone system.
Each handset must be registered with the telephone base before use. Additional
handsets registered to the telephone system are assigned numbers in the
sequential order.
When first purchased and properly charged, each expansion handset displays
Put handset on BASE to register. The new handset should be charged without
interruption for at least 30 minutes before registering it to the telephone base.
To register a handset:
ꢀ. Make sure the handset is out of the telephone base or handset charger and
shows Put handset on BASE to register. Place the handset you wish to
register in the telephone base.
IS7121 base
Do not place the handset
in the charger.
ꢁ. The handset displays Registering handset... then displays HANDSET X
Registered, and you hear a confirmation tone from the handset when
registration completes. It takes about 60 seconds to complete the
registration process.
Deregister handsets and doorbells
If you want to replace a handset, or reassign the designated handset number of a
registered handset, you must deregister all system devices and then register each
handset/doorbell individually.
Make sure you plug in AC power for the doorbells before deregistration.
To deregister all handsets and doorbells:
ꢀ. Press and hold /FIND HANDSET on the telephone base for about ꢀ0 seconds
until the IN USE light flashes.
ꢁ. Immediately press /FIND HANDSET again. You must press
/FIND HANDSET while the IN USE light is still flashing. The IN USE light
flashes for about five seconds.
3. All handsets show Put handset on BASE to register and all doorbell lights
flash quickly. The deregistration process takes about 10 seconds
to complete.
To register the handset(s) to the telephone base again, follow the registration
instructions above.
3
Handset overview
1
9
10
2
11
12
13
3
4
5
14
15
6
7
8
1 – CHARGE light
10 – Softkeys (2)
• Select a menu item displayed above
the key.
-
2 – q/VOL /CID
• Scroll down while in a menu, or in the
directory, caller ID log or redial list.
+
11 – p/VOL /
• Decrease the listening volume.
• Review the caller ID log.
• Scroll up while in a menu, or in the
directory, caller ID log or redial list.
• Increase the listening volume.
• Review the directory.
3 –
/FLASH
• Make or answer a call.
12 –
/VIEW
4 – 1
• Set or dial your voicemail number.
• Start video streaming.
13 – OFF/CANCEL
5 – Dialing keys
• Hang up a call.
• Return to the previous menu or idle
mode without making changes.
6 –
• Switch to tone dialing temporarily.
14 –
• Switch the character between upper
and lower case.
• Set and turn on the quiet mode, or
turn it off.
• Show other dialing options when
reviewing a caller ID log entry.
7 –
• Make or answer a call.
• Switch between the speakerphone and
the handset earpiece.
• Toggle the name order when saving
the caller ID entry into the directory.
8 – MUTE/DELETE
15 – REDIAL/PAUSE
• Review the redial list.
• Insert a dialing pause.
• Mute the microphone.
• Delete digits or characters.
9 – PUSH TO TALK (PTT)/SNAPSHOT
• Begin a one-to-one or one-to-group
broadcast.
• Take a photo shot of the visitor.
ꢂ
Battery
It takes up to ꢀ3 hours for the battery to be fully charged. When it is fully charged,
you can expect the following performance:
Operation
While in handset use (talking*)
While in speakerphone mode (talking*)
While not in use (standby**)
Operating time
Up to ꢀꢀ hours
Up to 6 hours
Up to 5 days
* Operating times vary depending on your actual use and the age of the battery.
** Handset is not charging or in use.
The battery needs charging when:
•
•
•
•
A new battery is installed in the handset.
The handset beeps.
A battery is properly installed and the screen is blank.
Low battery or Place in charger displays on the handset screen.
CAUTION:
To reduce the risk of fire or injury, read and follow these instructions:
•
Use only the battery provided or equivalent. To order a replacement, visit our
•
•
Do not dispose of the battery in a fire. Check with local waste management
codes for special disposal instructions.
Do not open or mutilate the battery. Released electrolyte is corrosive and
may cause burns or injury to the eyes or skin. The electrolyte may be toxic
if swallowed.
•
•
Exercise care in handling batteries in order not to create a short circuit with
conductive materials.
Charge the battery provided with or identified for use with this product only in
accordance with the instructions and limitations specified in this manual.
•
•
Observe proper polarity orientation between the battery and metallic contacts.
To prevent fire or shock hazard, do not expose this product to water or any type
of moisture.
Important safety instructions
When using your telephone equipment, basic safety precautions should always be followed to reduce the
risk of fire, electric shock and injury, including the following:
ꢀ. Read and understand all instructions.
ꢁ. Follow all warnings and instructions marked on the product.
3. Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a
damp cloth for cleaning.
ꢂ. Do not use this product near water such as near a bath tub, wash bowl, kitchen sink, laundry tub or a
swimming pool, or in a wet basement or shower.
5. Do not place this product on an unstable table, shelf, stand or other unstable surfaces.
6. Slots and openings in the back or bottom of the telephone base and handset are provided for ventilation.
To protect them from overheating, these openings must not be blocked by placing the product on a soft
surface such as a bed, sofa or rug. This product should never be placed near or over a radiator or heat
register. This product should not be placed in any area where proper ventilation is not provided.
ꢃ. This product should be operated only from the type of power source indicated on the marking label. If you
are not sure of the type of power supply in your home or office, consult your dealer or local power company.
8. Do not allow anything to rest on the power cord. Do not install this product where the cord may be
walked on.
9. Never push objects of any kind into this product through the slots in the telephone base or handset
because they may touch dangerous voltage points or create a short circuit. Never spill liquid of any kind
on the product.
ꢀ0. To reduce the risk of electric shock, do not disassemble this product, but take it to an authorized service
facility. Opening or removing parts of the telephone base or handset other than specified access doors
may expose you to dangerous voltages or other risks. Incorrect reassembling can cause electric shock
when the product is subsequently used.
ꢀꢀ. Do not overload wall outlets and extension cords.
ꢀꢁ. Unplug this product from the wall outlet and refer servicing to an authorized service facility under the
following conditions:
•
•
•
•
When the power supply cord or plug is damaged or frayed.
If liquid has been spilled onto the product.
If the product has been exposed to rain or water.
If the product does not operate normally by following the operating instructions. Adjust only those controls
that are covered by the operation instructions. Improper adjustment of other controls may result in damage
and often requires extensive work by an authorized technician to restore the product to normal operation.
•
•
If the product has been dropped and the telephone base and/or handset has been damaged.
If the product exhibits a distinct change in performance.
ꢀ3. Avoid using a telephone (other than cordless) during an electrical storm. There is a remote risk of electric
shock from lightning.
ꢀꢂ. Do not use the telephone to report a gas leak in the vicinity of the leak. Under certain circumstances, a
spark may be created when the adapter is plugged into the power outlet, or when the handset is replaced
in its cradle. This is a common event associated with the closing of any electrical circuit. The user should
not plug the phone into a power outlet, and should not put a charged handset into the cradle, if the
phone is located in an environment containing concentrations of flammable or flame-supporting gases,
unless there is adequate ventilation. A spark in such an environment could create a fire or explosion.
Such environments might include: medical use of oxygen without adequate ventilation; industrial gases
(cleaning solvents; gasoline vapors; etc.); a leak of natural gas; etc.
ꢀ5. Only put the handset of your telephone next to your ear when it is in normal talk mode.
ꢀ6. The power adapter is intended to be correctly oriented in a vertical or floor mount position. The prongs are
not designed to hold the plug in place if it is plugged into a ceiling, under-the-table or cabinet outlet.
SAVE THESE INSTRUCTIONS
5
Precautions for users of implanted cardiac pacemakers
Cardiac pacemakers (applies only to digital cordless telephones):
Wireless Technology Research, LLC (WTR), an independent research entity, led a multidisciplinary
evaluation of the interference between portable wireless telephones and implanted cardiac pacemakers.
Supported by the U.S. Food and Drug Administration, WTR recommends to physicians that:
Pacemaker patients
•
Should keep wireless telephones at least six inches from the pacemaker.
•
Should NOT place wireless telephones directly over the pacemaker, such as in a breast pocket, when it
is turned ON.
•
Should use the wireless telephone at the ear opposite the pacemaker.
WTR’s evaluation did not identify any risk to bystanders with pacemakers from other persons using
wireless telephones.
Operating range
This cordless telephone operates with the maximum power allowed by the Federal Communications
Commission (FCC). Even so, this handset and telephone base can communicate over only a certain
distance - which can vary with the locations of the telephone base and handset, the weather, and the
layout of your home or office.
When the handset is out of range, the handset displays Out of range or no pwr at base.
If there is a call while the handset is out of range, it may not ring, or if it does ring, the call may not connect
well when you press
. Move closer to the telephone base, then press
to answer the call.
If the handset moves out of range during a telephone conversation, there may be interference. To improve
reception, move closer to the telephone base.
ECO mode
This power conserving technology reduces power consumption for optimal battery performance. The ECO
mode activates automatically whenever the handset is synchronized with the telephone base.
Energy-saving charging mode
When this mode is activated, all telephone functions, except handset battery charging, will be disabled.
To activate the energy-saving charging mode:
ꢀ. Unplug the telephone base power adapter from the power outlet. Make sure all handsets are plugged with
charged batteries before proceeding.
ꢁ. While you press and hold /FIND HANDSET, plug the telephone base power adapter back to the
power outlet.
3. After about ꢁ0 seconds, when the IN USE light starts flashing, release /FIND HANDSET and then press it
again within ꢁ seconds.
When the phone successfully enters the energy-saving charging mode, the IN USE light turns off
and all handsets display Put handset on BASE to register.
When the phone fails to enter this mode, repeat Step ꢀ through Step 3 above.
Note: The telephone base will be powered up as normal if you fail to press /FIND HANDSET within
ꢁ seconds in Step 3.
To deactivate the energy-saving charging mode:
ꢀ. Unplug the telephone base power adapter from the power outlet, then plug it back in. Then the telephone
base is powered up as normal.
ꢁ. Register your handsets back to the telephone base. See page 3 for handset registration instructions.
Maintenance
Taking care of your telephone
Your cordless telephone contains sophisticated electronic parts, so it must be treated with care.
Avoid rough treatment
Place the handset down gently. Save the original packing materials to protect your telephone if you ever
need to ship it.
Avoid water
Your telephone can be damaged if it gets wet. Do not use the handset outdoors in the rain, or handle it with
wet hands. Do not install the telephone base near a sink, bathtub or shower.
Electrical storms
Electrical storms can sometimes cause power surges harmful to electronic equipment. For your own safety,
take caution when using electrical appliances during storms.
Cleaning your telephone
Your telephone has a durable plastic casing that should retain its luster for many years. Clean it only with a soft
cloth slightly dampened with water or mild soap. Do not use dampened cloth or cleaning solvents of any kind.
Remember that electrical appliances can cause serious injury if used when you are wet or standing in
water. If the telephone base should fall into water, DO NOT RETRIEVE IT UNTIL YOU UNPLUG THE
POWER CORD AND TELEPHONE LINE CORD FROM THE WALL. Then remove the telephone by the
unplugged cords.
About cordless telephones
•
Privacy: The same features that make a cordless telephone convenient create some limitations.
Telephone calls are transmitted between the telephone base and the cordless handset by radio
waves, so there is a possibility that the cordless telephone conversations could be intercepted by radio
receiving equipment within range of the cordless handset. For this reason, you should not think of
cordless telephone conversations as being as private as those on corded telephones.
•
•
Electrical power: The telephone base of this cordless telephone must be connected to a working
electrical outlet. The electrical outlet should not be controlled by a wall switch. Calls cannot be made
from the cordless handset if the telephone base is unplugged, switched off or if the electrical power
is interrupted.
Potential TV interference: Some cordless telephones operate at frequencies that may cause
interference to televisions and VCRs. To minimize or prevent such interference, do not place the
telephone base of the cordless telephone near or on top of a TV or VCR. If interference is experienced,
moving the cordless telephone farther away from the TV or VCR often reduces or eliminates
the interference.
•
•
Rechargeable batteries: Exercise care in handling batteries in order not to create a short circuit with
conducting material such as rings, bracelets and keys. The battery or conductor may overheat and
cause harm. Observe proper polarity between the battery and the battery charger.
Nickel-metal hydride rechargeable batteries: Dispose of these batteries in a safe manner. Do not
burn or puncture the battery. Like other batteries of this type, if burned or punctured, they could release
caustic material which could cause injury.
6
The RBRC® seal
The RBRC® seal on the nickel-metal hydride battery indicates that VTech
Communications, Inc. is voluntarily participating in an industry program to collect and
recycle these batteries at the end of their useful lives, when taken out of service within
the United States and Canada.
The RBRC® program provides a convenient alternative to placing used nickel-metal
hydride batteries into the trash or municipal waste, which may be illegal in your area.
VTech’s participation in RBRC® makes it easy for you to drop off the spent battery
at local retailers participating in the RBRC® program or at authorized VTech product
service centers. Please call 1 (800) 8 BATTERYTM for information on Ni-MH battery
recycling and disposal bans/restrictions in your area. VTech’s involvement in this
program is part of its commitment to protecting our environment and conserving
natural resources.
RBRC® is a registered trademark of Rechargeable Battery Recycling Corporation.
Limited warranty
What does this limited warranty cover?
The manufacturer of this VTech Product warrants to the holder of a valid proof of purchase (“Consumer” or
“you”) that the Product and all accessories provided in the sales package (“Product”) are free from defects
in material and workmanship, pursuant to the following terms and conditions, when installed and used
normally and in accordance with the Product operating instructions. This limited warranty extends only to
the Consumer for Products purchased and used in the United States of America and Canada.
What will VTech do if the Product is not free from defects in materials and workmanship during the
limited warranty period (“Materially Defective Product”)?
During the limited warranty period, VTech’s authorized service representative will repair or replace at
VTech’s option, without charge, a Materially Defective Product. If we repair the Product, we may use new
or refurbished replacement parts. If we choose to replace the Product, we may replace it with a new or
refurbished Product of the same or similar design. We will retain defective parts, modules, or equipment.
Repair or replacement of the Product, at VTech’s option, is your exclusive remedy. VTech will return the
repaired or replacement Products to you in working condition. You should expect the repair or replacement
to take approximately 30 days.
How long is the limited warranty period?
The limited warranty period for the Product extends for ONE (1) YEAR from the date of purchase. If VTech
repairs or replaces a Materially Defective Product under the terms of this limited warranty, this limited
warranty also applies to the repaired or replacement Product for a period of either (a) 90 days from the date
the repaired or replacement Product is shipped to you or (b) the time remaining on the original one-year
warranty; whichever is longer.
What is not covered by this limited warranty?
This limited warranty does not cover:
ꢀ. Product that has been subjected to misuse, accident, shipping or other physical damage, improper
installation, abnormal operation or handling, neglect, inundation, fire, water or other liquid intrusion; or
2. Product that has been damaged due to repair, alteration or modification by anyone other than an
authorized service representative of VTech; or
3. Product to the extent that the problem experienced is caused by signal conditions, network reliability, or
cable or antenna systems; or
4. Product to the extent that the problem is caused by use with non-VTech accessories; or
5. Product whose warranty/quality stickers, product serial number plates or electronic serial numbers have
been removed, altered or rendered illegible; or
6. Product purchased, used, serviced, or shipped for repair from outside the United States of America or
Canada, or used for commercial or institutional purposes (including but not limited to Products used for
rental purposes); or
7. Product returned without a valid proof of purchase (see item 2 below); or
8. Charges for installation or set up, adjustment of customer controls, and installation or repair of systems
outside the unit.
How do you get warranty service?
To obtain warranty service in the USA, visit our website at www.vtechphones.com or call 1 (800) 595-9511.
NOTE: Before calling for service, please review the user’s manual - a check of the Product’s controls and
features may save you a service call.
Except as provided by applicable law, you assume the risk of loss or damage during transit and transportation and
are responsible for delivery or handling charges incurred in the transport of the Product(s) to the service location.
VTech will return repaired or replaced Product under this limited warranty. Transportation, delivery or handling
charges are prepaid. VTech assumes no risk for damage or loss of the Product in transit. If the Product failure is
not covered by this limited warranty, or proof of purchase does not meet the terms of this limited warranty,
VTech will notify you and will request that you authorize the cost of repair prior to any further repair activity.
You must pay for the cost of repair and return shipping costs for the repair of Products that are not covered by this
limited warranty.
What must you return with the Product to get warranty service?
ꢀ. Return the entire original package and contents including the Product to the VTech service location along
with a description of the malfunction or difficulty; and
ꢁ. Include a “valid proof of purchase” (sales receipt) identifying the Product purchased (Product model) and
the date of purchase or receipt; and
3. Provide your name, complete and correct mailing address, and telephone number.
Other limitations
This warranty is the complete and exclusive agreement between you and VTech. It supersedes all other
written or oral communications related to this Product. VTech provides no other warranties for this Product.
The warranty exclusively describes all of VTech’s responsibilities regarding the Product. There are no other
express warranties. No one is authorized to make modifications to this limited warranty and you should not
rely on any such modification.
State/Provincial Law Rights: This warranty gives you specific legal rights, and you may also have other rights,
which vary from state to state or province to province.
Limitations: Implied warranties, including those of fitness for a particular purpose and merchantability (an
unwritten warranty that the Product is fit for ordinary use) are limited to one year from the date of purchase.
Some states/provinces do not allow limitations on how long an implied warranty lasts, so the above limitation
may not apply to you. In no event shall VTech be liable for any indirect, special, incidental, consequential,
or similar damages (including, but not limited to lost profits or revenue, inability to use the Product or other
associated equipment, the cost of substitute equipment, and claims by third parties) resulting from the use
of this Product. Some states/provinces do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitation or exclusion may not apply to you.
Please retain your original sales receipt as proof of purchase.
ꢃ
FCC, ACTA and IC regulations
FCC Part 15
This equipment has been tested and found to comply with the requirements for a Class B digital device
under Part ꢀ5 of the Federal Communications Commission (FCC) rules. These requirements are intended
to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications to this equipment not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
(ꢀ) this device may not cause harmful interference, and (ꢁ) this device must accept any interference
received, including interference that may cause undesired operation. Privacy of communications may not
be ensured when using this telephone.
To ensure safety of users, the FCC has established criteria for the amount of radio frequency energy
that can be safely absorbed by a user or bystander according to the intended usage of the product. This
product has been tested and found to comply with the FCC criteria. The handset may be safely held
against the ear of the user. The telephone base and the door bell shall be installed and used such that
parts of the user’s body other than the hands are maintained at a distance of approximately 20 cm
(8 inches) or more.
This Class B digital apparatus complies with Canadian ICES-003.
FCC Part 68 and ACTA
This equipment complies with Part 68 of the FCC rules and with technical requirements adopted by the
Administrative Council for Terminal Attachments (ACTA). The label on the back or bottom of this equipment
contains, among other things, a product identifier in the format US:AAAEQ##TXXXX. This identifier must
be provided to your telephone service provider upon request.
The plug and jack used to connect this equipment to premises wiring and the telephone network must
comply with applicable Part 68 rules and technical requirements adopted by ACTA. A compliant telephone
cord and modular plug is provided with this product. It is designed to be connected to a compatible modular
jack that is also compliant. An RJꢀꢀ jack should normally be used for connecting to a single line and an
RJꢀꢂ jack for two lines. See the installation instructions in the user’s manual.
The Ringer Equivalence Number (REN) is used to determine how many devices you may connect to your
telephone line and still have them ring when you are called. The REN for this product is encoded as the 6th
and 7th characters following the US: in the product identifier (e.g., if ## is 03, the REN is 0.3). In most, but
not all areas, the sum of all RENs should be five (5.0) or less. For more information, please contact your
telephone service provider.
This equipment may not be used with Party Lines. If you have specially wired alarm dialing equipment
connected to your telephone line, ensure the connection of this equipment does not disable your alarm
equipment. If you have questions about what will disable alarm equipment, consult your telephone service
provider or a qualified installer.
If this equipment is malfunctioning, it must be unplugged from the modular jack until the problem has been
corrected. Repairs to this telephone equipment can only be made by the manufacturer or its authorized
agents. For repair procedures, follow the instructions outlined under the Limited warranty.
If this equipment is causing harm to the telephone network, the telephone service provider may temporarily
discontinue your telephone service. The telephone service provider is required to notify you before
interrupting service. If advance notice is not practical, you will be notified as soon as possible. You will be
given the opportunity to correct the problem and the telephone service provider is required to inform you
of your right to file a complaint with the FCC. Your telephone service provider may make changes in its
facilities, equipment, operation, or procedures that could affect the proper functioning of this product. The
telephone service provider is required to notify you if such changes are planned.
If this product is equipped with a corded or cordless handset, it is hearing aid compatible.
If this product has memory dialing locations, you may choose to store emergency telephone numbers
(e.g., police, fire, medical) in these locations. If you do store or test emergency numbers, please:
Remain on the line and briefly explain the reason for the call before hanging up.
Perform such activities in off-peak hours, such as early morning or late evening.
Industry Canada
Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and
(ꢁ) this device must accept any interference, including interference that may cause undesired operation.
The term ‘’IC:‘’ before the certification/registration number only signifies that the Industry Canada technical
specifications were met.
The Ringer Equivalence Number (REN) for this terminal equipment is ꢀ.0. The REN is an indication of the
maximum number of devices allowed to be connected to a telephone interface. The termination on an
interface may consist of any combination of devices subject only to the requirement that the sum of the
RENs of all the devices does not exceed five.
This product meets the applicable Industry Canada technical specifications.
Technical specifications
Frequency control
Transmit frequency
Channels
Crystal controlled PLL synthesizer
ꢀ9ꢁꢀ.536-ꢀ9ꢁ8.ꢂꢂ8 MHz
5
LCD
128 (RGB) x 160 DOTS; 1.77’’; TFT PANEL
Nominal effective range
Maximum power allowed by FCC and IC. Actual operating range may
vary according to environmental conditions at the time of use.
Power requirements
Handset unit :2.4V Ni-MH battery
Charger unit power adapter : input :117V AC 50/60Hz
output: 6V AC @ 300mA
Memory
Directory: 50 memory locations; up to 30 digits and 15 characters
Caller ID log: 50 memory locations; up to 24 digits and 15 characters
VTECH TELECOMMUNICATIONS LTD.
A member of THE VTECH GROUP OF COMPANIES.
Distributed in the U.S.A. by VTech Communications, Inc., Beaverton, Oregon 9ꢃ008.
Distributed in Canada by VTech Technologies Canada Ltd., Richmond, B.C. V6W ꢀL5.
VTech is the registered trademark of VTech Holdings Limited.
Copyright © ꢁ0ꢀ3 for VTECH TELECOMMUNICATIONS LTD.
All rights reserved. Printed in China.
9ꢀ-006ꢂ8ꢀ-0ꢂ0-ꢀ00
8
|