Connect power to handset charger
Choose the location for your handset charger, and plug charger adapter into an
electrical outlet not controlled by a wall switch.
Register a handset
•
When the handset shows NOT REGISTERED, place
the handset on a base unit or charger that is connected
to a power outlet. The handset screen will display
PRESS FIND HNDST 4 SEC ON BASE.
Press and hold FIND HANDSET on the base unit
until the IN USE light comes on. (It takes at least four
seconds).
NOT RIGISTERD
Quick installation guide
i6720
•
•
Parts checklist:
Check to make sure the phone’s package includes the following:
1. AC power adapter
2. Charger
PRESS FIND HNDST
4 SEC ON BASE
�elease FIND HANDSET once the IN USE light comes
on.
3. Handset
NOTE:
4. Battery compartment cover
5. Belt clip
•
If PRESS FIND HNDST 4 SEC ON BASE does not appear on the screen after
a few seconds, lift up handset and place in base unit or charger again.
6. Battery
7. Quick installation guide
On the i6725 base:
Charge the handset battery
Place the handset in the base unit. CHARGING... will display on handset. Be
sure to charge the battery for at least 16 hours before using your telephone.
NOTE:
•
�eturn the handset to the base unit when not in use to ensure optimum
performance.
1. AC power adapter
3. Handset
2. Charger
On the i6765/75/85/86 base:
Belt clip
Align the pins on the inside edge of the clip with the notches on the sides of the
handset.
4. Battery compartment
cover
7. Quick installation
guide
5. Belt clip
6. Battery
NOTE:
•
com or call VTech Communications, Inc. at 1 (800) 595-9511. In Canada, go
1 (800) 267-7377.
To attach
To remove
After a while the handset will emit series of tones, the newly registered handset
will be assigned the lowest extension number not previously assigned to another
system handset when successfully registered. �epeat the steps in Register
a handset if the new handset does not successfully register to the base unit
within two minutes.
Install handset battery
1. Align the two holes in the plug with the socketpins, matching the red and the
black connectors, then snap plug into place.
2. Place the battery in the compartment with the wires in the upper right
corner.
3. Neatly tuck the wires next to the battery inside the battery compartment.
Registration
Tꢁ ꢈꢃꢊꢋꢉꢂꢃꢈ ꢂꢌꢃ ꢋ6720 ꢌꢍꢎꢏꢉꢃꢂ ꢂꢁ ꢅꢁuꢈ ꢁꢈꢋꢊꢋꢎꢍꢐ ꢉꢅꢉꢂꢃꢑ, ꢅꢁu ꢌꢍvꢃ ꢂꢁ ꢆꢈꢉꢂ ꢏꢃ-ꢈꢃꢊ-
ister all your handsets, then register the new handset and re-register all the old
handsets one at a time.
De-register all handsets
Note:
•
•
•
Press and hold FIND HANDSET on the base unit for four seconds, the IN
USE light will light up.
Keep pressing FIND HANDSET for another six seconds until the IN USE
ꢐꢋꢊꢌꢂ ꢉꢂꢍꢈꢂꢉ ꢂꢁ flꢍꢉꢌ, then release the FIND HANDSET button.
Press and release FIND HANDSET again. The IN USE light will turn off and
in a few seconds, all handsets will be de-registered.
•
If the de-register process does not work, you may need to reset the system
4. �eplace cover by sliding it upwards until it clicks into place.
and try again. To reset: pick up the handset and press TALK/
/FLASH.
Then, press the OFF button and place the handset back into the base unit.
ꢀ
Wꢌꢃꢎ ꢆꢈꢉꢂ �uꢈcꢌꢍꢉꢃꢏ ꢅꢁu ꢎꢃꢃꢏ ꢂꢁ cꢌꢍꢈꢊꢃ ꢅꢁuꢈ ꢌꢍꢎꢏꢉꢃꢂꢉ ꢄꢁꢈ ꢆvꢃ ꢑꢋꢎuꢂꢃꢉ
before registering to base unit.
On the i6725 base:
Important:
If this product is not working properly:
2. Call our customer service at 1-800-595-9511 or 1-800-267-7377 in Canada.
On the i6765/75/85/86 base:
NOTE:
•
Use only the VTech battery and AC power adapter supplied with this unit or the
recommended equivalent.
•
If you are not going to use the telephone for a long period of time, remove the
battery to prevent possible leakage.
•
•
�o not open or mutilate the battery. �eleased electrolyte is corrosive and may
cause damage to the eyes or skin. It may be toxic if swallowed.
Exercise care in handling batteries in order not to create a short circuit with
conducting materials such as rings, bracelets, and keys. The battery or
conductor may overheat and cause burns.
ꢀ
�ꢁ ꢎꢁꢂ ꢏꢋꢉ�ꢁꢉꢃ ꢁꢄ ꢂꢌꢃ �ꢍꢂꢂꢃꢈꢅ ꢋꢎ ꢍ ꢆꢈꢃꢇ ꢋꢂ ꢑꢋꢊꢌꢂ ꢃ��ꢐꢁꢏꢃ�
|