User’s Manual
TM
Spinning Spiral Tower Playset
© 2014 VTech
Printed in China
91-002904-006
INTRODUCTION
Thank you for purchasing the VTech® Go! Go! Smart Wheels®
Spinning Spiral Tower PlaysetTM learning toy!
Take a spin around the VTech® Go! Go! Smart Wheels® Spinning
Spiral Tower PlaysetTM!Your child will develop fine motor skills as they
park the included SmartPoint™ van, move it through the car wash and
launch it down the ramp. The van also responds to six SmartPoint™
locations on the playset.
6 SMARTPOINT™
LaunCher
LOCaTiOnS
Turning gaTe
SMARTPOINT™ Van
SPinning
gaTe
Car waSh
gaS STaTiOn
2
INCLUDED IN THIS PACKAGE
One user’s manual
One SmartPoint™ van
One tower base
One tower
roof piece
Four spiral ramp pieces
One tower sign
Five tower support pieces
One gate
One spinner
Two straight ramp track pieces
One car wash
One car
base track
wash piece
3
WARNING:
All packing materials, such as tape, plastic sheets, packaging
locks and tags are not part of this toy, and should be discarded
for your child’s safety.
ATTeNTION:
Pour la sécurité de votre enfant, débarrassez-vous de tous
les produits d’emballage tels que rubans adhésifs, feuilles de
plastique, attaches et étiquettes. Ils ne font pas partie du jouet.
NOTe:
Please keep this user’s manual as it contains important
information.
GETTING STARTED
BATTeRY INSTALLATION
1. Make sure the unit is turned OFF.
2. Locate the battery cover on the bottom
of the van. Use a coin or a screwdriver
to loosen the screw.
3. Install 2 new “AAA” (AM-4/LR03)
batteries following the diagram inside
the battery box. (The use of new
alkaline batteries is recommended for
maximum performance.)
4. replace the battery cover and tighten
the screw to secure the battery cover.
4
BATTeRY NOTICe
•
•
•
Use new alkaline batteries for maximum performance.
Use only batteries of the same or equivalent type as recommended.
Do not mix different types of batteries: alkaline, standard (carbon-
zinc) or rechargeable (Ni-Cd, Ni-MH), or new and used batteries.
•
•
•
•
•
•
•
•
Do not use damaged batteries.
Insert batteries with the correct polarity.
Do not short-circuit the battery terminals.
Remove exhausted batteries from the toy.
Remove batteries during long periods of non-use.
Do not dispose of batteries in fire.
Do not charge non-rechargeable batteries.
Remove rechargeable batteries from the toy before charging (if
removable).
•
Rechargeable batteries are only to be charged under adult
supervision.
5
ASSEMBLY INSTRUCTIONS
with the VTech® Go! Go! Smart Wheels® Spinning Spiral Tower
PlaysetTM, safety comes first. To ensure your child’s safety, adult
assembly is required.
Assemble the spiral tower:
1. Locate the tower base that is labeled
with a number “1” engraving on the
bottom. insert three tower support
pieces as shown.
2. Place the spiral ramp piece with the
number “2” engraving on the bottom
over the center pole on the tower base.
Then adjust the spiral ramp piece so
the slots on the bottom fit snugly onto
the two support pieces as shown.
3. attach the spiral ramp piece with the
number “3” engraving on the bottom
in the same way. adjust it so the spiral
fits snugly over the remaining support
piece.
4. insert the final two support pieces
into the slots of the spiral ramp with
the number “2” engraving.
6
5. repeat the steps above to attach
the spiral ramp with the number “4”
engraving. ensure the piece fits
snugly onto the two support pieces.
6. attach the spiral ramp with the
number “5” engraving on the bottom
to the number “4” spiral ramp;repeat
the above steps to attach the tower
roof, labeled with a number “6” into
place.
7. insert the tower sign into the slots on
the tower roof. attach the spinner to
the gate.Then insert the gate into the
slots on the tower base.
Assemble the car wash:
attach the car wash piece to the car wash base track. after that,
connect the car wash to the spiral tower using the ramp track with
the number “7” engraving. attach the ramp track with the number
“8” engraving to the car wash platform.
7
VAN FEATURES
1. ON/OFF SWITCH
To turn the van ON, slide the ON/
OFF SWITCH on the van to the ON
(
) position. To turn the van OFF,
slide the ON/OFF SWITCH to the
OFF ( ) position.
2. AUTOMATIC SHUT-OFF
To preserve battery life, the van included with the VTech®
Go! Go! Smart Wheels® Spinning Spiral Tower PlaysetTM will
automatically power-down after approximately 60 seconds without
input. The unit can be turned on again by pressing the light-up
driver button or pushing the van quickly.
Note:This product is in a try-me mode in the packaging.after opening
the package, turn the vehicle off and on again to proceed with
normal play.
VANACTIVITIES
1. Slide the ON/OFF SWITCH to
turn the van ON. You will hear van
sounds, a song and a phrase. The
light will flash with the sounds.
8
2. Press the LIGHT-UP BUTTON to
hear van sounds, songs and phrases.
The light will flash with the sounds.
3. Push the van to hear sounds and
melodies.while a melody is playing,
push the van again to add in fun
sounds on top of the melody. The
light will flash with the sounds.
4. For added fun, the van interacts with
the VTech® Go! Go! Smart Wheels®
Spinning Spiral Tower PlaysetTM
.
Simply roll the van over one of the
playset’s six SmartPointTM locations
to see the van’s light flash and to hear
greetings, fun sounds, short tunes
and sing-along songs.The van even
interacts with other Go! Go! Smart
Wheels® playsets (each playset sold
separately).
SPIRAL TOWERACTIVITIES
1. To launch the van down the spiral,
place the van on the LAUNCHeR
at the top of the tower. Lift up the
LAUNCHeR to see the van spin
down.
9
2. Switch the gate position near the
straight ramp to choose a different
route.
3. Put the included Go! Go! Smart
Wheels® SmartPoint™ van on one
of the playset’s six SmartPoint™
locations to hear fun phrases and
sounds. (SmartPoint™ vehicles
only.Other vehicles sold separately.)
4. Move the van through the CAR
WASH as you pretend to get your
vehicle sparkly clean.
5. Drive your vehicle into the GAS
STATION for a fill-up.
10
MeLODY LIST
1. The Old Grey Mare
2. She’ll be Coming ’Round the Mountain
3. Shoo Fly, Don’t Bother Me
4. This Old Man
5. Yankee Doodle
6. Bicycle Built for Two
CARE & MAINTENANCE
1. Keep the unit clean by wiping it with a slightly damp cloth.
2. Keep the unit out of direct sunlight and away from any direct heat
source.
3. remove the batteries when the unit will not be in use for an extended
period of time.
4. Do not drop the unit on hard surfaces and do not expose the unit
to moisture or water.
11
TROUBLESHOOTING
if for some reason the program/activity stops working or malfunctions,
please follow these steps:
1. Please turn the unit OFF.
2. interrupt the power supply by removing the batteries.
3. Let the unit sit for a few minutes, then replace the batteries.
4. Turn the unit ON. The unit should now be ready to play again.
5. if the product still does not work, replace with an entire set of new
batteries.
If the problem persists, please call our Consumer Services Department
at 1-800-521-2010 in the u.S. or 1-877-352-8697 in Canada, and a
service representative will be happy to help you.
For information on this product’s warranty, please call VTech® at
1-800-521-2010 in the u.S. or 1-877-352-8697 in Canada.
IMPORTANT NOTe:
Creating and developing Infant Learning products is accompanied
by a responsibility that we at VTech® take very seriously. we make
every effort to ensure the accuracy of the information, which forms
the value of our products. however, errors sometimes can occur.
it is important for you to know that we stand behind our products
and encourage you to call our Consumer Services Department at
1-800-521-2010 in the u.S. or 1-877-352-8697 in Canada, with
any problems and/or suggestions that you might have. a service
representative will be happy to help you.
Note:
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
12
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. however, there is no
guarantee that interference will not occur in a particular installation. if
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Caution: Changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority to
operate the equipment.
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.
OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:
(1)THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND
(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,
INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED
OPeraTiOn.
CAN ICES-3 (B)/NMB-3(B)
13
|