STEP1 Press the [CBL] button.
STEP3 Point the remote control toward the
equipment and enter the three-digit
code number assigned to your
brand from the code tables.
STEP4 Press the same [DEVICE] button
to store the code. The Device
LED will blink twice to confirm
that the code has been stored.
Introduction
Button Functions
3
1
Operating Instructions
For 3 Function
Cable Remote Control
STEP2 Press the [SYSTEM] button and the
[SELECT] button simultaneously for 3
seconds. The [CBL] button will turn
on for 20 seconds.
The remote control is designed to operate the
Scientific-Atlanta Explorer 2000 and 3000
Series and the Pioneer Voyager set top boxes
and the majority of TV and VCR/DVD equipment
on the market.
*Tip : The equipment will turn off when the
correct three-digit code number has
been entered. You can verify you have
selected the correct code by pressing
the [MUTE] button, the equipment
should turn on or turn off.
*Note : If there is more than one three-digit
number listed for your brand, try one
code number at a time until your
equipment turns off.
C. To Find the Three Digit Code
Number That was Stored in
the Device.
STEP3 Press the [DEVICE] button you wish
to store in the System On/Off button
and repeat this until you stored all
the power commands into the
System On/Off button.
UR3-EXP
Replacing Batteries
Before you program or operate the remote control,
you must install two new AA alkaline batteries.
STEP1 Press the [DEVICE] button (TV or
VCR) you wish to verify and the
[SELECT ]button simultaneously for 3
seconds.
2
STEP4 Press the [CH+] button to save the
power commands you stored. The
[CBL] button will blink twice to
confirm the saving.
STEP1 Remove the battery compartment cover
*Tip : The device LED will turn on for 20
seconds. The next step must be
entered while the LED is on.
on the back of your remote control.
STEP4 Store the three-digit code number
by pressing the same [DEVICE]
button once again. The device LED
will blink twice to confirm that the
code has been stored.
STEP2 Check battery polarity carefully, and
install the batteries as shown in the
illustration below.
F. Volume Punch Through:
STEP2 Press the [INFO] button.
By following the steps below, the user can
program the volume controls (Volume UP,
Volume Down and MUTE) from one device to
operate in another device mode.
The device LED will blink number of times
indicating the number of each digit of the
code number. Each digit is separated by a 1
second interval of the LED being turned off.
Example : One blink, three blinks and eight
blinks with an interval of 1 second
of LED being turned off, indicates
the code number 138.
STEP3 Replace the battery compartment cover.
*Note : Try all the functions on the remote
control. If any of the functions do not
work as they should, repeat from Step 2
using the next three-digit code number
from the same brand list. Make sure
that the VCR/VOD button is in the
VCR position when using your VCR.
The default volume control settings on the
remote control is TV volume control. If you
wish to store the CABLE volume control in
CBL mode, use the following steps.
STEP1 Press the [CBL] button and the
[SELECT] button simultaneously for
3 seconds.
Note : Ten blinks is equal to the number 0.
B. Auto Search Method.
*Tip :The device LED will light on for 20
seconds. The next step must be
entered while the LED is on.
D. Programming a second TV
to VCR Mode.
STEP1 Press the [VCR] button to be
programmed and the [SELECT]
button simultaneously for 3 seconds.
*Tip : The device LED will turn on for 20
seconds. The next step must be
entered while the LED is on.
If the three-digit code numbers assigned to
your brand do not turn off your equipment or
the code tables do not list your brand, you
can use the Auto Search Method to find the
correct three-digit code number for your
equipment by the following steps:
STEP2 Press the [VOL +] button.
STEP3 Press the [CBL] button.
The device LED will blink twice to
confirm the programming.
STEP1 Turn on the equipment you wish to
operate.
To return to original state:
STEP2 Press the [DEVICE] button (TV or
VCR) to be programmed and the
[SELECT] button simultaneously for 3
seconds. The device LED will turn on.
If you wish to restore the TV volume control in
STEP2 Press the [TV] device button to
CBL mode, repeat the above steps by
pick up the TV code table.
Operations
Default State :
Device Default : Scientific Atlanta Explorer
2000/3000 & Pioneer Voyager
4
pressing [TV] in STEP 3 .
STEP3 Point the remote control toward the
equipment and enter the three-digit
code number assigned to your TV
brand from the code tables.
STEP4 Store the three-digit code number by
pressing the [VCR] button once again.
The device LED will blink twice to
confirm that the code has been stored.
*Tip : The device LED will light on for 20
seconds. The next step must be
entered while LED is on.
Programming the Remote Control.
5
G. LOW BATTERY WARNING:
When the battery is low (2.0V-2.3V) and
needs to be replaced with fresh batteries,
the remote control LED will blink 2 times in
sequence whenever a [DEVICE] button is
pressed to turn on equipment.
A. Three-Digit Code Programming Method.
The remote control can be programmed by pressing in a three digit code number that
corresponds to particular manufacturers and brands of Audio/Video equipment.
The three-digit code numbers are listed in the code table of the instruction manual.
Volume Default : TV volume and mute through
the TV, with the option of controlling volume and
mute through the Cable Converter. Refer to
Section F for programming the volume and mute
through your Cable Converter.
STEP3 Point the remote control toward the
equipment and alternately press the
[CH+] (or [CH-]) button and the
[MUTE] button. If the right code
number is sent, the equipment will
turn off.
STEP1 Turn on the equipment you wish to program. (TV, VCR, or DVD)
H. Memory Lock System:
E. Programming the System On/Off Button.
System On/Off button :
STEP2 Press the [DEVICE] button (TV or VCR) to be programmed and the [SELECT] button
simultaneously for 3 seconds. The device LED will turn on indicating the unit is ready
to be programmed.
This remote control is designed to retain
programmed memory for 10 years even
after batteries are removed from the
remote control.
This is designed to program the System on/off
button so that it can send out up to three
power on/off commands for the devices you
programmed into the remote control.
*Tip : You can verify that you selected the
correct code by pressing the [MUTE]
button again. The equipment should
either turn on or turn off.
Universal Remote Control, Inc.
This button is designed to send out power
commands for two or all three devices with one
button press. Please refer to section E for details.
OEE-0049A Rev 07(06/30/04)
*Tip : The device LED will stay lit for 20 seconds. The next step must be entered while the LED is on.
|