ꢀ
MSR120 Simple Manual
2003/1/21
MSR 120 SERIES
Magnetic Stripe Card Reader
Universal Serial Bus (USB) Interface
Thank you for purchasing the MSR120 series products. The MSR120 Series USB Interface Magnetic Card Reader is ideal for retail
systems, time keeping systems, security systems and the card reader related systems. The MSR120 series are designed to offer the user
a card reader solution that will complement many applications. Triple track MSR120 reader is uniquely designed to read both credit
cards and Driver Licenses (AAMVA and California standard).
FEATURES
Light weight: 120g
Compact size: 100L*34W*28H (mm)
LED and Buzzer indicators indicate card status
Low power consumption
1
2
3
4
5
Single, dual, or triple track versions allow for reading all types of magnetic cards, including credit cards and drivers licenses.
CONFIGURATION
MSR120-33 Triple track 1&2&3
AGENCY APPROVED
- Comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules.
- Comply with CE mark Class A, UL, and cUL
WARRANTY
This product is served under one-year warranty of defects in material and functionality to the original purchasers. Within the warranty
period, if the product found to be defective will be repaired or replaced. This warranty applies to the products only under the normal use
of the original purchasers, and in no circumstances covers incidental or consequential damages through consumers’ misuse or
modification of the product.
WARNING
You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your
authority to operate the equipment.
SET-UP
1) Turn the system power off.
2) Connect PC and MSR120 USB connector of signal cable to a free USB port
3) Turn the system power on.
4) Install USB driver (ref. to Appendix A)
SPECIFICATIONS
Recording Method: Two-frequency coherent phase (F2F), compatible with ISO 7811 and AAMVA.
Swipe Speed:
5 to 50 in/sec (worst case with +/- 12% jitter card)
5VDC/120mA
Power Requirements:
ꢀ
Excerpt from MSR120 Programmer’s Manual (PM010, Rev.1.1)
Page 1 / 5
ꢀ
--- Proprietary and Confidential ---
ꢀ
MSR120 Simple Manual
2003/1/21
3. Insert the USB driver diskette (DISK 2) into the floppy drive and click Next to continue:
a. Select Search for the best driver for your device and click Next.
b. Select Specify a location and click Browse. Change the folder of your floppy drive
(i.e.: A:\Driver\Windows) and click OK.
c. Double-check the directory that Windows prompts. Click Next.
ꢀ
Excerpt from MSR120 Programmer’s Manual (PM010, Rev.1.1)
Page 3 / 5
ꢀ
--- Proprietary and Confidential ---
ꢀ
MSR120 Simple Manual
2003/1/21
d. Windows will detect the driver (SER9PL.inf) and shows the USB Card Reader.
Click Next to continue until installation is complete.
e. Click Next to continue and let Windows copy the needed files to your hard disk.
Click Finish while installation is complete.
f. After installing, the System will generate an additional COM Port, USB Card Reader (e.g.: COM3) for the connection to
RS232 Serial Device.
ꢀ
Excerpt from MSR120 Programmer’s Manual (PM010, Rev.1.1)
Page 4 / 5
ꢀ
--- Proprietary and Confidential ---
ꢀ
MSR120 Simple Manual
2003/1/21
ꢀ
Driver Un-installation
You can uninstall the MSR120 driver by executing Uninstall Program: Dremover98.exe in the driver diskette and click the
Remove button to accomplish the un-installation.
ꢀ
ꢀ
Excerpt from MSR120 Programmer’s Manual (PM010, Rev.1.1)
Page 5 / 5
ꢀ
--- Proprietary and Confidential ---
|