Revision 1.2
TYAN S1668
Dual Pentium Pro ATX
440FX PCI-ISA System Board
User's Manual
1. Introduction
1.1 Overview
The S1668 is a quality, high performance dual processor mainboard based
on the powerful Intel Pentium Pro microprocessors. This mainboard is
designed around the latest and fastest Intel 440FX chipset and can support
CPU speeds of 150MHz through 200MHz.
The S1668 supports EDO memory, Burst EDO, ECC and memory parity
checking.The S1668's PCI Local Bus provides high performance capabili-
ties that are ideal for a wide range of demanding applications such as:
CAD, CAM, CAE, networking, multi-user environments, database man-
agement, desktop publishing, image processing and 3D animation.
This integrated system board achieves the highest reliability and features
the industry standard "ATX" form factor. Some of the features included
are: on-board dual channel PCI IDE, on-board floppy controller, on-board
high speed I/O, Universal Serial Bus and on-board PS/2 mouse connector.
Flexibility and expandibility have been designed into the S1668. With I/O
and drive controller support built on-board, the five PCI and three ISA
(One ISA and one PCI as a shared slot) slots are free for add-on expansion
cards. With eight SIMM sockets, the S1668 can provide a very
flexible memory configuration of 8MB to 1024MB of RAM. With the
S1668's support for dual Pentium Pro processors, you can start a system
with just one CPU, and later add another, when more processing power is
required.
Remember to take a look at Tyan Computers web site located at
products along with FAQ's, distributors list, drivers and CMOS setting
explanations.
S1668-ATXD-o0w01nlohattdpf:r/o/wmwWww.twya.Sno.cmoamnuals.com3. All Manuals Search And Download.
1.2 Hardware Specifications/Features
CPU
Intel Pentium Pro 150 thru 200 MHz (Socket 8)
(Single or Dual CPU configuration)
Coprocessor
Speed
On-chip floating point unit
60/66 MHz system bus
30/33 MHz PCI bus
7.5/8.33 MHz ISA bus speed
DRAM
4 double banks of 72 pin SIMM sockets
Supports 5V or 3.3V memory
Supports BEDO(Burst Extended Data Out)
Supports EDO(Extended Data Out) DRAMs
Supports ECC(Error Correcting Code)w/ parity
Supports Fast Page Mode DRAMs
Supports 8MB to 1024MB of DRAMs
L2 Cache
256/512KB 2nd level cache in CPU
EIDE Controller
Primary and secondary PCI EIDE channels on
board for support of up to four EIDE Mode 0
through Mode 4 drives.Supports DMA mode 1
and 2.
Enhanced I/O
Multi-mode bi-directional parallel port that
supports standard, EPP and ECP modes.
Supports 16550 compatible UARTS for on-board
high speed serial ports.
Support for an IrDA compliant InfraRed inter-
face.
On-board floppy controller.
On-board USB(Universal Serial Port).
Mouse
On-board PS/2 mouse connector.
I/O Bus Slots
5 Master/Slave PCI-Bus
3 ISA Bus (One ISA and one PCI shared slot)
S1668-ATXD-o0w01nlohattdpf:r/o/wmwWww.twya.Sno.cmoamnuals.com4. All Manuals Search And Download.
1.3 Software Specifications
BIOS
Award or AMI BIOS
AT CMOS setup, BIOS/CHIPSET setup,
and hard disk utility included.
Support for easy BIOS upgrades with flash
EEPROM chip.
O.S.
Operates with MS-DOS, Windows 3.x, Windows
for Work Groups 3.x, Windows 95, Windows NT,
OS/2, Novell Netware, Novell UnixWare 1.1 and
SCO Unix.
1.3 Environment
Ambient Temperature
Relative Humidity
Altitude
Vibration
Voltage
0 to +50 C (operating)
0 to +85% (operating)
0 to 10,000 feet (operating)
0 to 1,000 Hz
4.9 to 5.2 V
Information presented in this publication has been carefully checked for
reliability; however, no responsibility is assumed for inaccuracies. The
information contained in this document is subject to change without
notice.
Trademarks
Award BIOS/Flash are trademarks ofAward Software International Inc.
AMI BIOS is a trademarks of American Megatrends Inc.
IBM,PC,AT,PS/2 are trademarks of IBM Corporation
INTEL,Pentium Pro are trademarks of Intel Corporation.
Copyright c 1996TYAN Computer Corp.
S1668, Titan ProATX.
S1668-ATXD-o0w01nlohattdpf:r/o/wmwWww.twya.Sno.cmoamnuals.com5. All Manuals Search And Download.
2. Board Installation
2.1 Unpacking
The mainboard package should contain the following:
S1668 Mainboard
One IDE 40 pin cable
One 34 pin floppy cable
User's Manual
Optional VRM(Voltage Regulator Module)
The mainboard contains sensitive electric components which can be easily
damaged by static electricity, so the mainboard should be left in its original
packaging until it is ready to be installed.
With the power supply pluged in and turned off touch an unpainted area of
the system chassis imedietly before handling the mainboard or any compo-
nent. Doing so discharges the static charge your body may have built.
After opening the mainboard carton, extract the system board holding it by
its edges ,and place it only on a grounded anti-static surface, component
side up. Inspect the board for damage. Press down on all of the socket IC's
to make sure that they are properly seated. Do this only with the board
placed on an anti-static mat. Do not touch the bottom of the board.
DO NOT APPLY POWER TO THE BOARD IF IT HAS BEEN
DAMAGED!
2.2 Installation
You are now ready to install your mainboard. The mounting hole pattern of
the S1668 matches the ATX system board spec. It is assumed that the
chassis is for a standard ATX mainboard form factor.
S1668-ATXD-o0w01nlohattdpf:r/o/wmwWww.twya.Sno.cmoamnuals.com6. All Manuals Search And Download.
3. On Board Resource Setting
Figure 3.1 S1668ATX Board Layout
PWR CON. 5V
J50
J49
J2
J48
J3
PS/2
KB
J4
J5
CPU 1
PS/2
Mouse
82441FX
J10
pin
1
J11
J12
82442FX
CPU 0
J14
J15
J16
J17
CON4
pin
1
PCI Slot 1
1
1
USB1
J18
CON5
J26
J20
USB2
pin
1
J27
pin
1
J25
PCI Slot 2
PCI Slot 3
PCI Slot 4
Floppy Con.
82371SB
1
pin
1J1
pin
1
J28
J29
Primary IDE
1
1
J31
Secondary IDE
PCI Slot 5
ISA Slot 1
pin
1
BIOS
AMI/AWARD
J32
KB CTR
ISA Slot 2
ISA Slot 3
J41
J42 J43
J44
RTC
pin
1
pin
1
pin
J45
1 J46 J47
Factory Default(do not change) Rev02 PCB
J31
J48
J49
off
off
off
S1668-ATXD-o0w01nlohattdpf:r/o/wmwWww.twya.Sno.cmoamnuals.com7. All Manuals Search And Download.
3.2 Jumper Settings:
CPU Speed: J27, J21, J22, J23, and J24
CPU Speed
150MHz
166MHz
180MHz
200MHz
J27
3-4
1-2
3-4
1-2
J21
off
off
on
J22
on
on
off
off
J23
on
on
on
on
J24
on
on
on
on
J11
on
off
on
J12
off
on
off
on
on
off
Host Bus Speed/PCI Bus Speed: J27
Host Speed
60MHz
66.67MHz
PCI Speed
30MHz
33.33MHz
J27
3-4
1-2
J11
on
off
J12
off
on
CPU Clock Multiplier: J21, J22, J23 and J24
Multiplier
X2
X2.5
X3
X3.5
X4
J21
off
off
on
off
on
J22
off
on
off
off
on
J23
off
on
on
on
J24
off
on
on
on
on
off
CMOS Resest/Password Reset: J41(Default off)
If you forget your CMOS password or need to reset the
CMOS registers, just power off the system and close
jumper J41for five seconds. Then open jumper J41 and
power on the system. This will set the CMOS and password
back to the system default.
DRAM Voltage: J2, J3, J14, J15, J4, J5, J16 and J17(Default 5V)
(Some EDO memory is 3.3V)
Voltage J2 J3 J14 J15 J4 J5 J16 J17
3.3V
5V
on on on on off off off off
off off off off on on on on
Warning, damage to system can result if set incorrectly!
S1668-ATXD-o0w01nlohattdpf:r/o/wmwWww.twya.Sno.cmoamnuals.com8. All Manuals Search And Download.
I/O Selection: J28 & J29
J28
1-2
2-3
J29
1-2
2-3
For COM 1 and 2
For InfraRed
Default
Speaker Connector: J43
Pinout Assignments
1
2
3
4
Speaker out
Ground
Ground
+ 5V
Keylock Connector: J44
Pinout Assignments
Pins 1 to 3 for power LED.
1
2
3
4
5
Led Output
No Connect
Ground
Keylock
Ground
Pins 4 and 5 for Keylock
Turbo Switch: J47 ( Non-Turbo Mode Not Supported )
HDD LED: J46
Pinout Assignments
1
2
3
4
Cathode
Anode
Cathode
Anode
Pins 1 and 2 are for primary IDE channel.
Pins 3 and 4 are for secondary IDE channel.
S1668-ATXD-o0w01nlohattdpf:r/o/wmwWww.twya.Sno.cmoamnuals.com9. All Manuals Search And Download.
Reset Connector: J45
Pinout Assignment
1
2
Power Good
Ground
Turbo LED Connector: J42
Pinout Assignment
1
2
Cathode
Anode
Flash EEPROM: J32(Default 5V)
This jumper should be left at the factory default.
Voltage
5V
12V
J32
1-2 (default)
2-3
InfraRed Interface: Con4 and Con5
Pinout Assignment
1
2
3
4
Signal In
Gnd
Signal Out
VCC
Super I/O Type: J26
Type
J26
665IR
669IR
1-2
2-3
This setting depends on what type of SMC I/O chip
is installed on the board. This jumper is set at the
factory and should not be changed.
S1668-ATXD-o0w01nlohattdpf:r/o/wmwWww.twya.Sno.cmoamnuals.co1m0. All Manuals Search And Download.
Soft Power On Switch: J1
Pinout Assignment
1
2
Soft Power On
Ground
CPU FAN Power: J49 and J50
Pinout Assignment
1
2
12Volts
Ground
3.3 CMOS RTC
CMOS RTC includes an internal battery and Real Time Clock circuit. It
provides the date and the time for the system. Normally the life span of a
RTC internal battery is 10 years. When replacing, you should use the same
model.
3.4 Speaker Connector Installation
S1668 provides a 4-Pin header (J43) to connect the speaker. The polarity
can go either way.
3.5 Turbo Switch
The front panel on your case may have a turbo switch to control system
speed when slower program execution is required for software developed
in the old XT days. The Intel 44FX chipset doesn't support a de-turbo
mode, but the S1668 has a connector (J47) for the cable that may come has
a connector (J47) for the cable that may come with the case.with the case.
3.6 Turbo LED Connector Installation
The TURBO LED on the front case panel can indicate the current speed
status of the system. The TURBO LED connector should be installed to
J42 in the correct direction.
S1668-ATXD-o0w01nlohattdpf:r/o/wmwWww.twya.Sno.cmoamnuals.co1m1. All Manuals Search And Download.
3.7 Hardware Reset Switch Connector Installation
The RESET switch on your cases' display panel provides users with the
HARDWARE RESET function which is the same as power on/off. The
system will do a cold start after the RESET switch is pushed by the user.
The RESET switch is a 2 pin connector and should be installed on jumper
J45.
3.8 Flash EEPROM-Jumper J32
The S1668 uses flash memory to store BIOS data. It can be updated as
new versions of the BIOS becomes available. The flash utility will guide
you through the process step by step. If your system is functioning properly,
you may want to forego updating your BIOS in the event the new one
causes problems with your existing hardware and software.
J32 determines which type of EPROM is used. This jumper has been set to
match the on board BIOS chip. The factory default for the S1668 is on pins
1-2.
Refer to chapter 6 for Flash EEPROM upgrade procedures.
3.9 Hardware CMOS & Password Reset
(The following steps are valid provided the board has a DS12887A RTC)
If you have been locked out of your system because you forgot your pass-
word or set the CMOS incorrectly, follow the instructions below.
a. Power off the system
b. Short jumper J41.
c. Wait for 5 seconds then remove the jumper from J41.
d.Then power on the system again.
By doing the above procedures, your password will be erased and the CMOS
will be reset to the BIOS defaults.
S1668-ATXD-o0w01nlohattdpf:r/o/wmwWww.twya.Sno.cmoamnuals.co1m2. All Manuals Search And Download.
3.10 DRAM Installation
The S1668 uses a 64-bit data path from memory to CPU and can
accommodate up to 1024 MB of RAM. The mainboard supports
standard, EDO (Extended Data Out) and ECC(Error Correcting Code)
72 pin SIMMS . All installed memory will be automatically detected so
there is no need to set jumpers.
SIMM modules must be installed in pairs.
Each pair of SIMMs must be of the same size and type.
The mainboard supports 1, 2, 4, 8, 16x32 or 32MBx32 SIMMS.
The table on the following page shows some of the available memory
configurations.
Voltage ID for Older Pentium Pro CPU's: J10 and J20
Most Pentium Pro CPU's will program the VRM to output
the correct voltage it requires, so these jumper are not important
and should be left open. Some early versions of the Pentium Pro
cannot program the VRM so you have to set these jumper manually.
J10 and J20 each have eight pins and are numbered as follows.
5
6
7
8
Pin #
3.5V
3.4V
3.3V
3.2V
3.1V
3.0V
2.9V
2.8V
2.7V
2.6V
2.5V
2.4V
2.3V
2.2V
2.1V
4--8
on
on
on
on
on
on
on
on
off
off
off
off
off
off
off
3-7
on
on
on
on
off
off
off
off
on
on
on
on
off
off
off
off
2-6
on
on
off
off
on
on
off
off
on
on
off
off
on
on
off
off
1-5
on
off
on
off
on
off
on
off
on
off
on
off
on
off
on
off
1
2 3 4
Default off
S1668-ATXD-o0w01nlohattdpf:r/o/wmwWww.twya.Sno.cmoamnuals.co1m3. All Manuals Search And Download.
Memory Table
Bank0
4MBx2
Bank1
none
Bank2
none
Bank3
none
Total
8MB
8MBx2
none
none
none
16MB
4MBx2
8MBx2
4MBx2
4MBx2
8MBx2
4MBx2
none
none
none
4MBx2
none
none
none
4MBx2
none
16MB
32MB
32MB
32MB
16MBx2
16MBx2
32MBx2
64MBx2
16MBx2
32MBx2
32MBx2
32MBx2
64MBx2
128MBx2
64MBx2
64MBx2
128MBx2
128MBx2
128MBx2
128MBx2
128MBx2
128MBx2
128MBx2
16MBx2
none
none
none
none
none
16MBx2
none
32MBx2
32MBx2
none
none
none
none
16MBx2
none
none
32MBx2
none
none
none
64MBx2
none
64MBx2
none
64MBx2
32MBx2
64MBx2
128MBx2
64MB
64MB
128MB
128MB
128MB
192MB
256MB
256MB
256MB
384MB
512MB
512MB
640MB
768MB
768MB
832MB
896MB
1024MB
16MBx2
32MBx2
32MBx2
32MBx2
64MBx2
none
64MBx2
64MBx2
128MBx2
64MBx2
128MBx2
128MBx2
128MBx2
128MBx2
128MBx2
none
64MBx2
64MBx2
none
64MBx2
128MBx2
64MBx2
128MBx2
128MBx2
128MBx2
S1668-ATXD-o0w01nlohattdpf:r/o/wmwWww.twya.Sno.cmoamnuals.co1m4. All Manuals Search And Download.
3.11 CPU Installation
Many types of Pentium Pro (150 thru 200 MHz) CPUs can be used on
the S1668. Please refer to the previous pages for the correct CPU jumper
settings for your board.
The CPU is a sensitive electronic component and it can be easily
damaged by static electricity. Do not touch the CPU pins with your
fingers.
When installing the CPU into the socket, match the CPU pins to the
socket pins.
Before the CPU is installed, the mainboard must be placed on a flat
plane in order to avoid being broken by the pressure of CPU insertion.
A cooling fan and heat sink assembly is required to protect the
CPU from being damaged.
1. Make sure the ZIF socket lever is up. To raise the lever, pull it out
to the side a little and raise it as far as it will go. The top plate will
slide back.
2. Align the CPU and socket Pin 1 corners. The pins on the bottom
of the CPU should align with the rows of holes in the socket.
3. Insert the CPU in the socket. It should insert easily. If it does
not, adjust the position of the lever a little.
4. Press the lever down. The top plate will slide forward. You will
feel some resistance as the pressure starts to secure the CPU in
the socket. This is normal and will not damage the CPU.
When the CPU is installed, the lever should snap into place at the
side of the socket in the down position.
S1668-ATXD-o0w01nlohattdpf:r/o/wmwWww.twya.Sno.cmoamnuals.co1m5. All Manuals Search And Download.
3.12 VRM Installation
The VRM is required for the Pentium Pro to work. The CPU will
program the VRM for the correct voltage needed. No jumper settings
are needed, just install the VRM into the VRM socket nearest the
CPU that is being installed. The VRM can only fit in the socket one
way so there is no danger of installing it incorrectly. Not all VRM's
will work in the S1668. Make sure you purchased a qualified VRM.
VRM socket 0 is for CPU socket 0.
VRM socket 1 is for CPU socket 1.
3.13 Peripheral Device Installation
After all the jumpers on the mainboard have been set, then it can be mounted
into the case. Then proceed to install the display card and any other
peripheral devices.
If a PCI-Bus interface card is to be installed in the system, any one of the
four PCI-Bus slots can support either a Master or a Slave device.
After installing the peripheral controller, the user should check everything
again, and prepare to power-on the system.
3.14 Connecting the Power Supply & On/Off Switch
The system power supply connectors on the mainboard is for a
standard ATX power supply. It can only be plugged in one way and
should install in easily.
ATX cases have an on/off switch that can be used to turn on or off
the ATX powersupply without having to use the switch that is on
the back of the powersupply.Use jumper J1 is for the on/off button from the
system case.
S1668-ATXD-o0w01nlohattdpf:r/o/wmwWww.twya.Sno.cmoamnuals.co1m6. All Manuals Search And Download.
4. BIOS Configuration
Award's BIOS has a built in setup program that allows the user to modify
the basic system configuration. This type of information is stored in the
battery-backed CMOS SRAM. Entering incorrect information or for-
getting your password can lock you out of your system.(refer to 3.15
for resetting of CMOS)
4.1. Entering Setup
Power ON the computer and press <Del> immediately and you will enter
Setup. The other way to enter setup is to power on the computer, when the
below message appears briefly at the bottom of the screen during the post
(Power On Self Test), press <Del> key or simultaneously press <Ctrl>,
<Alt>, and <Esc> keys.
* TO ENTER SETUP BEFORE BOOT PRESS CTRL-ALT-
ESC OR DEL KEY
If the message disappears before you respond and you wish to enter Setup,
restart the system by turning it OFF then ON or by pressing "Reset" on the
system case. You may also restart by simultaneously pressing <Ctrl>, <Alt>,
and <Del> keys. If you do not press the keys at the correct time, the
system will not boot and an error message will appear on the screen.You
will be asked to,
* PRESS F1 TO CONTINUE, CTRL-ALT-ESC OR DEL TO
ENTER SETUP.
Figure 4.1 will appear on the sceen. The Main Menu allows you to select
from the 8 setup functions and 2 exit choices. Use the arrow keys to select
among the items and press <Enter> to accept or enter each sub-menu.
S1668-ATXD-o0w01nlohattdpf:r/o/wmwWww.twya.Sno.cmoamnuals.co1m7. All Manuals Search And Download.
4.2. Control Keys
PgUp key Increases the numeric value or make changes
PgDn key Decreases the numeric value or make changes
F1 key
General help, only for Status Page Setup menu
and Option Page Setup Menu
Change color from a total of 16 colors
Calendar, only for Status Page Setup Menu
Reserved
F2 key
F3 key
F4 key
F5 key
Restore the previous CMOS value, only for Option
Page Setup Menu
F6 key
F8 key
F9 key
Load defaults
Reserved
Reserved
F10 key Save all CMOS changes, only for Main Menu
S1668-ATXD-o0w01nlohattdpf:r/o/wmwWww.twya.Sno.cmoamnuals.co1m8. All Manuals Search And Download.
4.3. Getting Help
4.3.1. Main Menu
The on-line description of the highlighted setup function is displayed at the
bottom of the screen.
4.3.2. Setup Page menu/Option Page Setup Menu
Press F1 to pop up a small help window that describes the appropriate keys
to use and the possible selections for the highlighted items. To exit the Help
Window, press <Esc>.
4.4. The Main Menu
Once you enter the Award BIOS CMOS Setup Utility, the Main Menu
(Figure 4.4) will appear on the screen. The Main Menu allows you to
select from the eight setup functions and 2 exit choices. Use the arrow
keys to select among the items and press <Enter> to accept or enter the
sub-menu.
Figure 4.4: Main Menu
ROM ISA BIOS (2A59CT51)
CMOS SETUP UTILITY
AWARD SOFTWARE, INC.
STANDARD CMOS SETUP
BIOS FEATURED SETUP
CHIPSET FEATURES SETUP
POWER MANAGEMENT
PNP/PCI CONFIGURATION
LOAD BIOS DEFAULTS
INTEGRATED PERIPHERAL
SUPERVISOR PASSWORD
USER PASSWORD
IDE HDD AUTO DETECT
SAVE AND EXIT
EXIT WITHOUT SAVING
ESC : Save & Exit Setup
F10 : Quit
:Select Item
:Change Color
(Shift)F2
Time, Date, Hard Disk Type,.....
S1668-ATXD-o0w01nlohattdpf:r/o/wmwWww.twya.Sno.cmoamnuals.co1m9. All Manuals Search And Download.
Standard CMOS setup
This setup page includes all the items in a standard compatible BIOS.
BIOS features setup
This setup page includes all of the enhanced features of Award's BIOS.
Chipset features setup
This setup page includes all the items of the 430HX chipset features.
Power Management setup
Change, set, or disable system power management options
PNP/PCI Configuration
This setup page allows you to modify the configuration of PCI slot
parameters.
Load setup defaults
BIOS defaults indicate the most appropriate values of each system param-
eter for your system.
Supervisor/User Password
Change, set, or disable password. It allows you to limit access to the
system and Setup.
Integrated Peripherals
This option lets the you enable or disable on board FDD, HDD,
and I/O options.
IDE HDD auto detection
Automatically configure hard disk parameters.
Save and exit setup
Save changes to CMOS and exit setup
Exit without saving
Abandon all CMOS changes and exit setup.
S1668-ATXD-o0w01nlohattdpf:r/o/wmwWww.twya.Sno.cmoamnuals.co2m0. All Manuals Search And Download.
4.5. Standard CMOS Setup Menu
The items in Standard CMOS Setup Menu (Figure 4.5) are divided into 9
categories. Each category includes one or more setup items. Use the
arrows to highlight the item and use the <PgUp> or <PgDn> keys to
select the value you want for each item.
Figure 4.5: Standard CMOS Setup Menu
ROM ISA BIOS (2A59CT51)
STANDARD CMOS SETUP
AWARD SOFTWARE, INC.
Date (mm:dd:yy) : Tue, Dec 7 1995
Time (hh:mm:ss) : 18 : 01 : 38
Type Size CYLS. HEADS. PRECOMP. LANDZONE SECTORS
Primary Master : none 0mb
Primary Slave: none 0mb
Secondary Master: none 0mb
Secondary Slave: none 0mb
Drive A : 1.44 M, 3.5 in.
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Base Memory:
Extended Memory: 7168 K
Expanded Memory: 0 K
640 K
Drive B : 1.2 M, 5.25 in.
Video : EGA/VGA
Halt On : All errors
Other Memory:
384 K
Total Memory:
8192 K
ESC: Quit
: Select Item
(Shift)F2: Change Color
PU/PD/+/-:
F3: Toggle Calendar
Modify
F1:
Help
Date
The date format is <month>, <day>, <year>. Press <F3> to show the
calendar.
Time
The time format is <hours>, <minutes>, <seconds>. The time is calcu-
lated based on the 24-hour military-time clock. For example 1 p.m. is
13:00:00.
Day The day, from Sun to Sat, Determined by the BIOS date,
month and year entries.
Date The date, from 1 to 31 (or maximum allowed in a month)
Month The month, Jan to Dec.
Year The year, from 1900 to 2099
S1668-ATXD-o0w01nlohattdpf:r/o/wmwWww.twya.Sno.cmoamnuals.co2m1. All Manuals Search And Download.
Primary/Secondary Drive type
This category identifies the types of hard disk drives that have been in-
stalled in the computer. There are 46 predefined types and a user definable
type.
Press PgUp or PgDn to select a numbered hard disk type or type a number
and press <Enter>. Note that the specifications of your drive must match
with the drive table. The hard disk will not work properly if you enter
improper information for this category. If your hard disk type is not listed,
you can Type User to define your own drive manually.
If you select Type User, you will be asked to enter the following info. Enter
the parameters directly from the keyboard and press <Enter>. The hard
disk information should be provided in the documentation from the hard disk
vendor or the system manufacturer.
CYLS
HEADS
number of cylinders
number of heads
PRECOMP
LANDZONE
SECTORS
Mode Normal
Mode LBA
Mode Large
written precom
landing zone
number of sectors
Access mode for IDE drives under 528MB
Access mode for EIDE drives over 528MB
Access mode for IDE drives over 528MB that don't
support LBA
If a SCSI hard disk has been installed or you have a CD-ROM/Tape
drive connected to an IDE channel, select NONE and press<Enter>.
Drive A type/Drive B type
This category identifies the types of floppy disk drive A or B, that
have been installed in your computer.
None
No floppy drive installed
360K, 5.25 in. 5-1/4 inch PC-type standard drive; 360 kilobyte capacity
1.2M,5.25 in.
720K, 3.5 in.
5-1/4 inch AT-type high-density drive; 1.2 megabyte capacity
3-1/2 inch double-sided drive; 720 kilobyte capacity
1.44M, 3.5 in. 3-1/2 inch double-sided drive; 1.44 megabyte capacity
2.88M, 3.5 in. 3-1/2 inch double-sided drive; 2.88 megabyte capacity
S1668-ATXD-o0w01nlohattdpf:r/o/wmwWww.twya.Sno.cmoamnuals.co2m2. All Manuals Search And Download.
Video
This category detects the type of graphics adapter used for the primary
display system. It must match your video display card and monitor. Al-
though secondary monitors are supported, you do not have to select that
type in setup.
EGA/VGA
Enhanced Graphics Adapter/Video Graphics Array.
For VGA,SVGA, or PGA monitor adapters.
CGA 40
CGA 80
Mono
Color Graphics Adapter, power up in 40 column mode.
Color Graphics Adapter, power up in 80 column mode.
Monochrome adapter, includes hi-res monochrome.
Halt On
The category determines whether the computer will stop if an error is
detected during power up.
All errors
No errors
Whenever the BIOS has detected a non-fatal error, the
system will be stopped and you will be promted.
The system boot will not be stopped for any errors that
are detected.
All, but Keyboard The system boot will not stop for a keyboard error;it
will stop for all other errors.
All, but Diskette
The system boot will not stop for disk errors; it will
stop for all other errors.
All, but Disk/Key The system boot will not stop for a keyboard or disk
error; it will stop for all other errors.
Memory
The category is for display-only and it is determined by POST Power On
Self Test of the BIOS.
Base Memory
The POST of the BIOS will determine the amount of
base (or conventional) memory installed in the system.
The value of the base memory is typically 640K.
Extended Memory
The BIOS determines how much extended memory is
present during the POST. This is the amount of
memory located above 1MB in the CPU's memory
address map.
S1668-ATXD-o0w01nlohattdpf:r/o/wmwWww.twya.Sno.cmoamnuals.co2m3. All Manuals Search And Download.
Expanded Memory
Expanded Memory (EMS) defines a 64 K page frame in
the area between 640K and 1Mb containing four 16K pages
that are windows into the EMS memory. Programs issue
requests to the EMS manager to switch the page to any
part of EMS memory. Extended memory can be converted
to emulate EMS by using a memory manager such as
EMM386 that ships with Windows and DOS.
Other Memory
This refers to memory located in the 640K to 1024K ad
dress space. This memory can be used for different
applications. DOS uses this area to load device drivers to
keep as much conventional memory free for application
programs as possible.
4.6. BIOS FEATURES SETUP
ROM ISA BIOS
BIOSFEATURESSETUP
AWARD SOFTWARE, INC.
Video BIOS Shadow
:Enabled
:Disabled
:Disabled
:Disabled
:Disabled
:Disabled
:Disabled
Virus Warning
CPU Internal Cache
External Cache
Boot Sequence
Swap Floppy Drive
Boot Up Floppy Seek
Boot Up NumLock Status :On
Memory Parity Check
Gate A20 Option
:Enabled
:Enabled
:Enabled
:A,C
:Disabled
:Enabled
C8000-CBFFF Shadow
CC000-CFFFF Shadow
D0000-D3FFF Shadow
D4000-D7FFF Shadow
D8000-DBFFF Shadow
DC000-DFFFF Shadow
:Enabled
:Fast
Typematic Rate Setting
:Disabled
Typematic Rate (Chars/sec) :6
ESC :Quit
F1 :Help
F5 :Old Values (Shift)F2 :Color
F6 :Load BIOS Defaults
:Select Item
Typematic Delay (msec)
Security Option
PS/2 mouse function
PCI/VGA Palette Snoop
:250
:Setup
:Disabled
:Disabled
PU/PD/+/- :Modify
F7 :Load Setup Defaults
S1668-ATXD-o0w01nlohattdpf:r/o/wmwWww.twya.Sno.cmoamnuals.co2m4. All Manuals Search And Download.
Virus warning
This category flashes on screen. During and after the system boot up,
any attempt to write to the boot sector or the partition table of the hard
disk drive will halt the system and the following error message will
appear. In the meantime, you can run an anti-virus program to locate the
problem. Default value is Enabled.
Enabled Activate automatically when the system boots up causing
a
warning
message to appear when anything attemps to access the boot sector or
hard disk partition table.
Disabled No warning message to appear when anything attemps to access the boot
sector or hard disk partition table.
CPU Internal Cache/External Cache
These two categories speed up the memory access. However, it de-
pends on the CPU/Chipset design. Default value is Enabled.
Enabled Enables the cache
Disabled Disables the cache
Boot Sequence
This category determines which drive the computer searches first for the
disk operating system (i.e. DOS). Default value is A,C.
A,C System will first search for floppy disk drive then hard disk drive.
C,A System will first search for hard disk drive then floppy disk drive
Swap Floppy Drive
Default value is Disabled
Enabled Floppy A & B will be swapped under DOS
Disable Floppy A & B will be normal definition.
S1668-ATXD-o0w01nlohattdpf:r/o/wmwWww.twya.Sno.cmoamnuals.co2m5. All Manuals Search And Download.
Boot Up Floppy Seek
During POST, the BIOS will determine if the floppy disk drive installed is
40 or 80 tracks. 360K type is 40 tracks while 720K, 1.2M and 1.44M
are all 80 tracks. Default value is Enabled
Enabled BIOS searches for floppy disk drive to determined if it is 40 or 80
tracks. Note that the BIOS cannot tell from 720k, 1.2M or 1.44M
drive type as they are all 80 tracks
Disabled BIOS will not search for the type of floppy disk drive by track
number. Note that there will not be any warning messages if the
drive installed is 360K
Boot Up NumLock Status
Default value is On
On
Off
Keypad is number keys
Keypad is arrow keys
Memory Parity Check
The default value is disabled
Gate A20 Option
Gate A20 controls the ability to access memory addresses above 1 MB
by enabling (Fast) or disabling (Normal) access to the processor.
Default value is Fast
Typematic Rate Setting, Typematic Rate (char/sec), and
Typematic Delay.
Typematic Rate Setting enables or disables the following two options.
TheTypematic Rate (6, 8, 10, 12, 15, 20, 24, or 30 characters per second)
and Typematic Rate Delay (250, 500, 750, or 1000 milliseconds) controls
the speed at which the keystroke is repeated. The selected character is
displayed when a key is held down after a delay set by the Typematic
Rate Delay. It then repeats at a rate set by the Typematic Rate.
S1668-ATXD-o0w01nlohattdpf:r/o/wmwWww.twya.Sno.cmoamnuals.co2m6. All Manuals Search And Download.
Security Option
This category allows you to limit access to the system setup, or just
setup. Default value is Setup
System The system will not boot and access to Setup will be denied if the correct
password is not entered at the prompt
Setup
The system will boot, but access to setup will be denied if the password is
not entered at the prompt
PS/2 Mouse Function
Enables or disables PS/2 mouse function. Default is Disabled.
PCI/VGA Palette Snooping
The purpose of this option is to allow multiple VGA devices on
different busses in a system to have data written from CPU to each
set of palette registers of every video device. Default is disabled.
Video BIOS Shadow
It determines whether Video BIOS will be copied to RAM, however, it
is an optional chipset design. Default is Enabled.
4.7 Chipset Features Setup
This screen controls the settings for the board's chip set. The controls for
this screen are the same as the previous screen. They should not be
changed unless you are familiar with the chipset.
The Chipset Features Screen
ROM ISA BIOS
CHIPSET SETUP UTILITY
AWARD SOFTWARE, INC.
8 bit I/O Recovery Time
16 bit I/O Recovery Time
Memory Hole at 15-16M
:1
:1
:Disable
Auto Configuration
DRAM Speed Selection
DRAM RAS# Precharge Time :4
:Enable
:70ns
MA Additional Wait State
RAS# to CAS# Delay
DRAM Read Burst(B/E/F)
DRAM Write Burst(B/E/F)
:Enable
:Enable
:x1/2/3
:x2/2/3
More Information on these settings
can be found at Tyan's web site.
ISA Bus Clock
:PCICLK/4
DRAM Refresh Queue
DRAM RAS# Only Refresh
ECC Checking/Generation
Fast DRAM Refresh
Read-Around-Write
PCI Burst Write Combine
PCI to DRAM Pipline
CPU to PCI Write Post
CPU to PCI IDE Post
System Cacheable
:Disable
:Disable
:Disable
:Disable
:Disable
:Disable
:Disable
:Disable
:Disable
:Enable
:Enabled
ESC :Quit
F1 :Help
:Select Item
PU/PD/+/- :Modify
F5 :Old Values (Shift)F2 :Color
F6 :Load BIOS Defaults
Video Cacheable
F7 :Load Setup Defaults
S1668-ATXD-o0w01nlohattdpf:r/o/wmwWww.twya.Sno.cmoamnuals.co2m7. All Manuals Search And Download.
4.7.1 Power Management Setup
ROM ISA BIOS
POWER MANAGEMENT SETUP
AWARD SOFTWARE, INC
Power Management
PM Control By APM
Video Off Method
:Disabled
:No
:Blank Screen
IRQ3 (Com2)
IRQ4 (Com1)
IRQ5 (LPT2)
IRQ6 (Floppy Disk)
IRQ7 (LPT1)
IRQ8 (RTC Timer)
IRQ9 (IRQ2 Redir)
IRQ10 (Reserved)
IRQ11 (Reserved)
IRQ12 (PS/2 Mouse)
IRQ13 (Coprocessor)
IRQ14 (Hard Disk)
IRQ15 (Reserved)
:Off
:Off
:Off
:Off
:Off
:Off
:Off
:Off
:Off
:Off
:Off
:Off
:Off
Doze Mode
:Disabled
:Disabled
:Disabled
:Disabled
Standby Mode
Suspend Mode
HDD Power Down
IRQ3 (Wake-Up Event) :Off
IRQ4 (Wake-Up Event) :Off
IRQ8 (Wake-Up Event) :Off
IRQ12 (Wake-Up Event) :Off
Power Management
Options are disabled, user defined, Min saving, and Max saving.
PM Control by APM(Advanced Power Management)
Options are "Yes" and "No". When set for "No", system BIOS will
ignore APM when power managing the system. If set on "Yes" the
system BIOS will wait for APM's prompt before it enters any PM
mode, e.g. Doze, Standby or Suspend.
Video Off Method
The "Blank Screen" option will let the system BIOS blanks the screen
when disabling video. V/H SYNC+Blank will let the BIOS turn off the
V-SYNC and H-SYNC signals from the VGA card to the monitor.
S1668-ATXD-o0w01nlohattdpf:r/o/wmwWww.twya.Sno.cmoamnuals.co2m8. All Manuals Search And Download.
Doze Mode
Defines the continous idle time before the system enters Doze mode.
Standby Mode
Defines the continous idle time before the system enters Standby mode.
Power Down Activities
Defines the the activities that can cause the PM timers to reload. (Break-
ing out of PM Mode)
S1668-ATXD-o0w01nlohattdpf:r/o/wmwWww.twya.Sno.cmoamnuals.co2m9. All Manuals Search And Download.
4.8 PCI Slot Configuration
ROM ISA BIOS
PCI/PNP Configuration
AWARD SOFTWARE, INC.
Resource Controlled by
Reset Configuration
:Manual
:Disabled
PCI IRQ Activated By:
PCI IDE IRQ Map To: Auto
Level
Primary IDE INT#:
Secondary IDE INT#:
A
B
IRQ3 assigned to
IRQ4 assigned to
IRQ5 assigned to
IRQ7 assigned to
IRQ9 assigned to
:legacy ISA
:legacy ISA
:PCI/PnP
:legacy ISA
:PCI/PnP
IRQ10 assigned to :PCI/PnP
IRQ11 assigned to :PCI/PnP
IRQ12 assigned to :PCI/PnP
IRQ14 assigned to :legacy ISA
IRQ15 assigned to :legacy ISA
DMA0 assigned to :PCI/PnP
DMA1 assigned to :PCI/PnP
DMA3 assigned to :PCI/PnP
DMA5 assigned to :PCI/PnP
DMA6 assigned to :PCI/PnP
DMA7 assigned to :PCI/PnP
ESC: Quit
F1 : Help
F5 : Old Values (Shift)F2 :Color
F6 : Load BIOS Defaults
F7 : Load Setup Defaults
:Select Item
:Modify
PU/PD/+/-
PCI Slot 1/Slot 2/Slot 3/Slot 4/Slot 5 INT#
For Default Setting.
Connect to PCI System INT#
INTA
PCI Slot1 INTA
PCI Slot1 INTB
PCI Slot1 INTC
PCI Slot1 INTD
PCI Slot2 INTA
PCI Slot2 INTB
PCI Slot2 INTC
PCI Slot2 INTD
PCI Slot3 INTA
PCI Slot3 INTB
PCI Slot3 INTC
PCI Slot3 INTD
PCI Slot4 INTA
PCI Slot4 INTB
PCI Slot4 INTC
PCI Slot4 INTD
PCI Slot5 INTA
PCI Slot5 INTB
PCI Slot5 INTC
INTB
INTC
INTD
INTB
INTC
INTD
INTA
INTC
INTD
INTA
INTB
INTD
INTA
INTB
INTC
INTA
INTB
INTC
PCI Slot5 INTD
INTD
S1668-ATXD-o0w01nlohattdpf:r/o/wmwWww.twya.Sno.cmoamnuals.co3m0. All Manuals Search And Download.
Resources Controlled By
The Award Plug and Play BIOS can automatically configure all the boot
and Plug and Play compatible devices. If you seelect Auto, all the
interrupt request and DMA assignment fields disappear, as the BIOS
automatically assigns them.
IRQ n assigned to
When resources are controlled manually, assign each system interrupt
as one of the following types, depending on the type of device using
the interrupt.
Legacy ISA
Devices compliant with the original PC AT bus specification.
PCI/ISA PnP
Devices compliant with the Plug and Play standard, whether designed
for the PCI or ISA bus architecture.
PCI IRQ Activated By:
Select the PCI IRQ Active scheme either LEVEL or EDGE.
Default value is LEVEL.
PCI IDE IRQ Map To:
Select the IDE IRQ Map to ISA IRQ#.
Primary IDE INT#
Select the PCI INT# that the Primary IDE controller will use.
Default value is A.
Secondary IDE INT#
Select the PCI INT# that the Secondary IDE controller will use.
Default value is B
S1668-ATXD-o0w01nlohattdpf:r/o/wmwWww.twya.Sno.cmoamnuals.co3m1. All Manuals Search And Download.
4.9 Integrated Peripherals
Integrated Peripherals
Award Software, Inc.
IDE HDD Block Mode
:Enabled
:Auto
:Auto
:Auto
:Auto
IDE Primary Master PIO
IDE Primary Slave PIO
IDE Secondary Master PIO
IDE Secondary Slave PIO
On-Chip Primary PCI-IDE
:Enable
On-Chip Secondary PCI-IDE :Enable
PCI Slot IDE 2nd Channel
:Enable
On-Board FDC Controller
On-Board Serial Port 1
On-Board Serial Port 2
On-Board Parallel Port
Parallel Port Mode
:Enable
:Com1/3F8
:Com2/2F8
:378/IRQ7
:Normal
The Settings in the Integrated Peripherals lets the user enable or
disable on-board device. You can also configure the I/O and IRQ
settings of the on-board serial and parallel ports.
S1668-ATXD-o0w01nlohattdpf:r/o/wmwWww.twya.Sno.cmoamnuals.co3m2. All Manuals Search And Download.
4.10. LOAD SETUPDEFAULTS
ROM ISA BIOS
CMOS SETUP UTILITY
AWARD SOFTWARE INC.
STANDARD CMOS SETUP
PASSWORD SETTING
IDE HDD AUTO DETECTION
SETUP
BIOS FEATURES SETUP
CHIPSET F
PCI SLOT
LOAD SETUP DEFAULTS
Load Setup Defaults (Y/N)? N
T SAVING
ESC : Save & Exit Setup
F10 : Quit
:Select Item
:Change Color
(Shift)F2
Load SETUP Defaults except standard CMOS SETUP
Load SETUP defaults
To load SETUP default values to CMOS SRAM, enter "Y". If not,
enter "N"
If any problem has occurred, loading the SETUP DEFAULTSis
recommended.
4.10. PASSWORD SETTING
When you select this function, the following message will appear at the
center of the screen to assist you in creating a password.
ENTER PASSWORD
S1668-ATXD-o0w01nlohattdpf:r/o/wmwWww.twya.Sno.cmoamnuals.co3m3. All Manuals Search And Download.
ROM ISA BIOS
CMOS SETUP UTILITY
AWARD SOFTWARE, INC.
STANDARD CMOS SETUP
PASSWORD SETTING
IDE HDD AUTO DETECTION
T SETUP
BIOS FEATURES SETUP
CHIPSET FE
PCI SLOT CO
LOAD SETUP DEFAULTS
Enter Password
UT SAVING
ESC : Save & Exit Setup
F10 : Quit
:Select Item
:Change Color
(Shift)F2
Change/Set/Disable Password
Type the password, up to eight characters, and press <Enter>. The
password typed now will clear the previously entered password from
CMOS memory. You will be asked to confirm the password. Type the
password again and press <Enter>. You may also just press <Esc> to
abort the selection and not enter a password.
To disable the password, just press <Enter> when you are prompted to
enter a password. A message will confirm that the password has been
disabled, the system will boot and you can enter Setup freely.
PASSWORD DISABLED
If you select System at Security Option of BIOS Features Setup Menu, you
will be prompted for the password every time the system is rebooted or any
time you try to enter setup. If you select Setup at Security Option of BIOS
Features Setup Menu, you will be prompted only when you try to enter
setup.
S1668-ATXD-o0w01nlohattdpf:r/o/wmwWww.twya.Sno.cmoamnuals.co3m4. All Manuals Search And Download.
4.11. IDE HDDAUTO DETECTION
ROM ISA BIOS
CMOS SETUP UTILITY
AWARD SOFTWARE, INC.
CYLS.
HEAD
PRECOMP LANZONE SECTORS
Drive C:
(202 Mb)
989
12
65535
989
35
Do you want to accept this as drive C (Y/N)?
Esc:Skip
Type "Y" to accept the H.D.D parameter reported by BIOS. Type "N" to keep the old
H.D.D parameter info.
4.12. SAVE & EXIT SETUP
ROM ISA BIOS
CMOS SETUP UTILITY
AWARD SOFTWARE, INC.
STANDARD CMOS SETUP
BIOS FEATURES SETUP
PASSWORD SETTING
IDE HDD AUTO DETECTION
SETUP
CHIPSET FE
Save to CMOS and EXIT (Y/N)? N
PCI SLOT C
UT SAVING
LOAD SETUP DEFAULTS
ESC : Save & Exit Setup
F10 : Quit
:Select Item
:Change Color
(Shift)F2
Type "Y" and you will quit the Setup Utility and save the user setup values
to RTC CMOS SRAM. Type "N" to return to Setup Utility.
S1668-ATXD-o0w01nlohattdpf:r/o/wmwWww.twya.Sno.cmoamnuals.co3m5. All Manuals Search And Download.
5.0 Flash Writer Utility
You can upgrade the BIOS of your mainboard by using a "Flash
MemoryWriter"(FMW) utility. This utility can be downloaded from the
factory's BBS(Consult your system vendor for the phone #). The
system BIOS is stored on a 'flash' EPROM chip on the mainboard
which can be erased and reprogrammed by the FMW.
The following three files make up the FMW.
AWDFLASH.EXE
-The Flash MemoryWriter utility for
Award to Award upgrade.
AMIFLASH.COM -The Flash Memory Writer utility for
AMI to AMI upgrade.
README
-A text file of instructions
*S62AWXX.BIN
-XX-A2-digit version number.
Flash memory writer records (or ‘programs’) a new BIOS
onto the flash memory chip.You cannot upgrade anAward
BIOS to a AMI BIOS or a AMI BIOS to an Award BIOS.
*This file name is subject to change and can have either a "bin" or a
"rom"extension.
S1668-ATXD-o0w01nlohattdpf:r/o/wmwWww.twya.Sno.cmoamnuals.co3m6. All Manuals Search And Download.
To reprogram the System BIOS, you must first do the following:
1. Check jumper J32
The S1668 uses a 5V Flash EPROM so jumper J32
should be left in the default postion on pins 1 and 2. This
jumper should never be moved.
2. Make sure the CPU is running in ‘real mode’.
FMW will not run if the CPU is operating in a protected or
virtual mode. This means that you can not run it withWindows
running or with any memory manager software. You must
disable any memory manager first. The easiest way to do this
is to:
a. Boot your system from a bootable floppy disk with no
CONFIG.SYS orAUTOEXEC.BAT files, and then run Flash
Memory Writer from a backup copy of your support disk. You
can make your back-up floppy bootable when you format it, and
use one disk for both purposes.
b. If you are using MS-DOS 6.x, you can use the feature that
allows you to bypass the CONFIG.SYS andAUTOEXEC.BAT
file. You do this while pressing <F5> while the “Starting MS-
DOS...” line is on the screen.
There are other ways to accomplish the same result. The main
point is to make sure no memory managers are running. If you
are not sure, try running FMW. If it runs, then you have suc-
ceeded. If it displays a warning message about the CPU
mode, you will have to try again.
S1668-ATXD-o0w01nlohattdpf:r/o/wmwWww.twya.Sno.cmoamnuals.co3m7. All Manuals Search And Download.
Once you have satisfied the two requirements mentioned above,
you can run FMW. You can copy the contents of the “Flash”
directory to your hard drive, or you can run the utility from a
backup of the support floppy disk. Make sure the new BIOS file
isinthe same directory as the FMWutility.
To run FMW, change to the “Flash” directory if you are not al-
ready in it. Type “Awdflash” at the DOS command line and press
the <Enter> key. The following screen will appear.
5.1 The Flash Memory Writer Utility Screen (Award)
FLASH MEMORY WRITER V3.0
Copyright (C) 1993, AWARD Software Inc.,
For FX/HX-2A59CT51
Date:4/13/95
File Name to Program:
Error Message:
Type in the whole file name, e.g. A62AW10.BIN and confirm
that you want to program the BIOS. The utility will then ‘Blank’,
‘Erase’, and then ‘Program’ the flash memory on the mainboard with the
new BIOS file. You should choose “yes” to save the original system
BIOS to a floppy diskette before you program the new BIOS. This
leaves you with a backup of your original BIOS in case you need to re-
install it. This option is highly recommended. If you can not sucessfully
program the BIOS file for whatever reason, re-install you original BIOS
from the backup file.
Warning: If you do not successfully install a complete BIOS file
in the flash memory on the Mainboard, your system may not be able to
boot. If this happens, it will require service by your system vendor.
Follow the requirements and instructions in this section precisely to aviod
inconvenience.
S1668-ATXD-o0w01nlohattdpf:r/o/wmwWww.twya.Sno.cmoamnuals.co3m8. All Manuals Search And Download.
6.0 System Resources
6.1. TIMER & DMA CHANNEL MAP
TIMER MAP:
TIMER Channel-0 system timer interrupt
TIMER Channel-1 DRAM REFRESH request
TIMER Channel-2 SPEAKER tone generator
DMA CHANNELS:
DMAChannel-0Available
DMA Channel-1 Available
DMA Channel-2 FLOPPY DISK adapter
DMAChannel-3Available
DMA Channel-4 Cascade for DMA controller 1
DMAChannel-5Available
DMAChannel-6Available
DMAChannel-7Available
6.2 INTERRUPT MAP
NMI:
Parity check error
IRQ (H/W)
0 System TIMER interrupt from TIMER-0
1 KEYBOARD output buffer full
2 Cascade for IRQ 9-15
3 SERIAL port 2
4 SERIAL port 1
5 PARALLEL port 2
6 FLOPPY DISK adapter
7 PARALLEL port 1
8 RTC clock
9Available
10Available
11Available
12Available
13 MATH co-processor
14 Primary IDE Channel
15 Secondary IDE Channel
S1668-ATXD-o0w01nlohattdpf:r/o/wmwWww.twya.Sno.cmoamnuals.co3m9. All Manuals Search And Download.
|