Owner’s Manual
PDU Rackmount Power Strips
Designed for Mounting in 19 in. Racks
Español: p. 3 • Français: p. 5
IMPORTANT SAFETY INSTRUCTIONS. This manual contains information
concerning the proper installation and use ofTripp Lite’s Rackmount Power Strips.
SAVE THESE INSTRUCTIONS.
Do not connect your power strip to an ungrounded outlet. Do not use it with extension cords
or adapters that eliminate its connection to ground. Your power strip is designed for indoor
use only. Install it away from heat emitting devices such as radiators and heat registers. Do
not install where excessive moisture or other conductive contaminants are present. Never
install electrical wiring during a lightning storm.
The power requirement of each device connected to an outlet of your power strip must not
exceed the Outlet Power Rating of your power strip (see Specifications). The total power
requirements of all devices connected to your power strip must not exceed the Maximum
Load Rating of your power strip (see Specifications).
1U Rackmount Installation
To Mount Unit in Rack: Put four user-supplied rackmount
screws (A) through the unit’s mounting ears (B) and into the
rack rails as shown. The user must determine the fitness of the
rackmount screws to hold the unit in the rack before
installation.
0U Rackmount Installation
1. Reorient Mounting Ears: Unscrew the screws (A) holding
the unit’s mounting ears (B) to the sides of the unit. Use
the screws from Step 1 (A) to reattach the mounting ears
1U Rackmount Installation
(B) to the unit as shown. Use only the manufacturer-
supplied screws or their equivalent (#6-32, ¼" flat head)
to reattach the mounting ears.
2. Mount Unit on Outside of Rack Rails: Put four user-
supplied screws (C) or similar mounting hardware
through the unit’s mounting ears (B) and into the side of
the rack as shown. The user must determine the fitness of
the user-supplied mounting hardware to support the unit
before mounting.
Wallmount/Under Counter Installation
Reorient the unit’s mounting ears as per the 0U Rackmount
Installation above, then put four user-supplied screws or
similar mounting hardware through the unit’s mounting ears
and into the mounting surface. The user must determine the
fitness of the user-supplied mounting hardware to support
the unit before mounting.
0U Rackmount Installation
Features
Circuit Breaker(s)
If the current draw of the equipment connected to your power strip exceeds your model’s Maximum Load
Rating (see Specifications) for longer than a few seconds, a circuit breaker will trip to prevent any possible
damage. When a circuit breaker trips, its plunger will pop up. Remove excess equipment and allow the breaker
to cool one minute before depressing its plunger to reset the breaker.
Grounding Lug
Use this screw (located by the power strip’s receptacles) to connect your power strip to ground.
Input Receptacle (IEC Model Only)
The PDU12IEC has no power cord. Instead, it has a IEC320-C20 inlet receptacle. To connect a PDU12IEC
to utility power, use a user-supplied detachable power cord with an IEC plug on one end and a plug
appropriate to your local utility outlets on the other.
Specifications
PDU1215
PDU1220
PDU2430
Nominal Voltage/Frequency:
Output Power Rating (amps):
AC Receptacles:
120V/50 or 60 Hz
15 amps
13 x NEMA 5-15R
(12 rear/1 front)
120V/50 or 60 Hz
20 amps
13 x NEMA 5-15/20R
(12 rear/1 front)
120V/50 or 60 Hz
24 amps
24 x NEMA 5-15R
(12 rear/12 front)
AC Line Cord:
15', w/NEMA 5-15P plug
15 amps
1¾ × 17¼ × 3¾
UR, cUR
15', w/NEMA 5-20P plug 15', w/NEMA L5-30P plug
Circuit Breaker(s) (Resettable):
Dimensions (HxWxD, inches):
Approvals:
20 amps
2 x 15 amps
1¾ × 17¼ × 3¾
UL, cUL
1¾ × 17¼ × 3¾
UR, cUR
PDU12IEC
PDU1220T
Nominal Voltage/Frequency:
Output Power Rating (amps):
100V to 240V/50 or 60Hz
15 amps for 100V to 120V or
16 amps for 208 to 240V
120V/50 or 60 Hz
20 amps
AC Receptacles:
4 x IEC-C13 (front),
13 x NEMA 5-15/20R
(12 rear/1 front)
15', w NEMA L5-20P plug
20 amps
1¾ × 17¼ × 3¾
UR, cUR
8 x IEC-C13/2 x IEC-C19 (rear)
N/A (IEC320-C20 inlet)
2 x 16 amps
1¾ × 17¼ × 3¾
CE, UL, cUL
AC Line Cord:
Circuit Breaker(s) (Resettable):
Dimensions (HxWxD, inches):
Approvals:
Limited Lifetime Warranty
Seller warrants this product, if used in accordance with all applicable instructions, to be free from original defects in material and
workmanship for its lifetime. If the product should prove defective in material or workmanship within that period, Seller will repair or
replace the product, in its sole discretion. Service under this Warranty can only be obtained by your delivering or shipping the product
(with all shipping or delivery charges prepaid) to: Tripp Lite, 1111 W. 35th Street, Chicago, IL 60609. Seller will pay return shipping
charges. Call Tripp Lite at (773) 869-1234 before sending any equipment back for repair.
THIS WARRANTY DOES NOT APPLY TO NORMAL WEAR OR TO DAMAGE RESULTING FROM ACCIDENT, MISUSE, ABUSE OR
NEGLECT. SELLER MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY EXPRESSLY SET FORTH HEREIN.
EXCEPT TO THE EXTEND PROHIBITED BY APPLICABLE LAW, ALL IMPLIED WARRANTIES, INCLUDING ALL
WARRANTIES OF MERCHANTABILITY OR FITNESS, ARE LIMITED IN DURATION TO THE WARRANTY PERIOD SET FORTH
ABOVE; AND THIS WARRANTY EXPRESSLY EXCLUDES ALL INCIDENTAL AND CONSEQUENTIAL DAMAGES. (Some states
do not allow limitations on how long an implied warranty lasts, and some states do not allow the exclusion or limitation of incidental
or consequential damages, so the above limitations or exclusions may not apply to you. This Warranty gives you specific legal rights,
and you may have other rights which vary from jurisdiction to jurisdiction).
WARNING: The individual user should take care to determine prior to use whether this device is suitable, adequate or safe
for the use intended. Since individual applications are subject to great variation, the manufacturer makes no
representation or warranty as to the suitability or fitness of these devices for any specific application.
Policy of Tripp Lite is one of continuous improvement. Specifications are subject to change without notice.
2
|