Owner’s Manual
SmartRack™ Accessories
Models: SRCABLETRAY, SRCABLETRAYEXP
1 – Introduction
2
2
2
2
3
3
3
4
4
4
1-1 Parts List
1-2 Tools Required
2 – Important Safety Instructions
3 – SRCABLETRAY Installation
4 – SRCABLETRAYEXP Installation
4-1 One Expansion Section
4-2 Two Expansion Sections
5 – Storage and Service
6 – Warranty and Warranty Registration
1111 W. 35th Street, Chicago, IL 60609 USA
Copyright © 2008 Tripp Lite. All trademarks are the sole property of their respective owners.
3 – SRCABLETRAY Installation
Note: You can remove the roof panel to aid installation, but this step is not required.
1
2
Assemble the cable tray by attaching the support sections
to
Insert the tabs
at one side of the cable tray into the matching
A
C
the trough section
with the included screws. Note: The support
roof panel slots . (Several sets of slots are compatible, allowing
B
D
sections should be attached inside the flanges of the trough
you to adjust the cable tray’s position to match your preference.)
section, not outside.
C
C
A
B
A
D
D
1
3
2
4
Compress the unattached cable tray support section
until you
Use the included hex nut
and lock washers
to connect one
A
G
H
can insert the remaining tabs
into the matching roof panel
end of the included ground cable
to a grounding post
at
E
I
J
the corner of the cable tray. Connect the other end of the ground
cable to the metal frame of the rack enclosure. (Follow the ground
wires connected to the rack enclosure’s doors to locate several
convenient ground connection points on the frame.)
slots . When you release pressure from the cable tray support
sections, they will expand to provide a secure fit.
F
G
J
H
TO
H
E
F
E
F
I
3
4
4 – SRCABLETRAYEXP Installation
Note: You must install SRCABLETRAY before installing SRCABLETRAYEXP. SRCABLETRAYEXP includes two expansion sections; you may
install one or both, depending on your needs.
4-1 One Expansion Section
1
Attach the expansion section
included screws.
to the cable tray
with the
A
B
A
B
1
3
4 – SRCABLETRAYEXP Installation
4-2 Two Expansion Sections
(continued)
1
2
Place the second expansion section
Place the first expansion section
on the cable tray
as shown.
on the first expansion
A
B
C
section
as shown. Align the screw holes of the cable tray and
A
expansion sections, then connect the expansion sections to the
cable tray with the included screws.
C
A
A
B
1
2
5 – Storage and Service
Storage
The unit must be stored in a clean, secure environment with a temperature less than 40° C (104° F) and a relative humidity less than 90% (non-
condensing). Store the unit in its original shipping container if possible.
Service
The unit is covered by the limited warranty described in this manual. For more information, call Tripp Lite Customer Service at +1.773.869.1234.
6 – Warranty and Warranty Registration
Limited Warranty
Seller warrants this product, if used in accordance with all applicable instructions, to be free from original defects in material and workmanship for a period of 5 years from the date of initial purchase.
If the product should prove defective in material or workmanship within that period, Seller will repair or replace the product, in its sole discretion.
THIS WARRANTY DOES NOT APPLY TO NORMAL WEAR OR TO DAMAGE RESULTING FROM ACCIDENT, MISUSE, ABUSE OR NEGLECT. SELLER MAKES NO EXPRESS WARRANTIES
OTHER THAN THE WARRANTY EXPRESSLY SET FORTH HEREIN. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ALL IMPLIED WARRANTIES, INCLUDING ALL WARRANTIES
OF MERCHANTABILITY OR FITNESS, ARE LIMITED IN DURATION TO THE WARRANTY PERIOD SET FORTH ABOVE; AND THIS WARRANTY EXPRESSLY EXCLUDES ALL INCIDENTAL AND
CONSEQUENTIAL DAMAGES. (Some states do not allow limitations on how long an implied warranty lasts, and some states do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitations or exclusions may not apply to you. This Warranty gives you specific legal rights, and you may have other rights which vary from jurisdiction to jurisdiction.)
Tripp Lite; 1111 W. 35th Street; Chicago IL 60609; USA
WARNING: The individual user should take care to determine prior to use whether this device is suitable, adequate or safe for the use intended. Since individual applications are subject to great
variation, the manufacturer makes no representation or warranty as to the suitability or fitness of these devices for any specific application.
Warranty Registration
Visit www.tripplite.com/warranty today to register the warranty for your new Tripp Lite product.You’ll be automatically entered into a drawing for a chance to win a FREE Tripp Lite product!*
* No purchase necessary. Void where prohibited. Some restrictions apply. See website for details.
Tripp Lite has a policy of continuous improvement. Specifications are subject to change without notice.
Made in China.
1111 W. 35th Street, Chicago, IL 60609 USA
200804131
93-2807
4
|