Table of Contents
Controller Components................................................. 2
Selecting Control Options ............................................ 3
Before Programming the Controller…..........................4
About The Controller’s Memory ................................... 4
Set Satellite Operating Mode........................................ 4
Set Current Time and Day............................................. 5
Set Station Run Times................................................... 5
Set Program Start Time(s) ............................................ 6
Set Active Day Watering Schedules ............................ 7
• Calendar Schedule.................................................... 7
• Interval Schedule ...................................................... 8
Set Program Repeat and Soak ..................................... 9
Program Operation Pause and Cancel ...................... 10
Manual Control Operations ...................................10- 12
Cycle Mode................................................................... 10
Syringe Mode ............................................................... 11
Multi-Manual Mode ...................................................... 12
Set Satellite Address................................................... 13
Set Percent Adjust....................................................... 13
Reviewing Program Information ................................ 14
Special Functions................................................... 14-15
Self Test........................................................................ 14
Initialization.................................................................. 14
Radio Calibration Test................................................. 15
Link Monitor ................................................................ 15
Troubleshooting .......................................................... 16
Lithium Battery Installation (Optional)....................... 16
Manual Output Switch Operation ............................... 17
Power Indicator Lamps ............................................... 17
Program Data Reference Form....................................18
Power Specifications
Electromagnetic Compatibility
Line Voltage: 115/230 V a.c. 50/60 Hz (switchable),
130 VA (100W)
Domestic: This equipment has been tested and found to
comply with the limits for a FCC Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful
interference when the equipment is operated in a
commercial environment. The equipment generates, uses,
and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction
manual, may cause harmful interference to the radio
communications. Operation in a residential area is likely to
cause harmful interference in which case the user will be
required to correct the interference at his own expense.
Current Draw (no load): 0.21A @ 115 V a.c., 60 Hz, 0.10A
@ 230V, 50 Hz
Current Draw (maximum load): 0.90A @ 115 V a.c, 60 Hz,
0.42A @ 230 V a.c, 50 Hz
Secondary Voltage Output: 24 V a.c., 3.2A (77 VA)
Maximum Load Per Station Output: 0.75A (18 VA)
Maximum Load Per Pump/Master Valve Output:
0.75A (18 VA)
Hardware Features
Plastic or Painted Stainless Steel Cabinetry
Front, Back and Top Locking Covers
International: This is a CISPR 22 Class A product. In a
domestic environment, this product may cause radio
interference, in which case the user may be required to
take adequate measures.
Removable Station Output and Common/Pump Modules
Modular Station Output:
16 to 64 stations in 8-station increments
Fuses and Circuit Breakers
Power Supply:
1.5A On/Off Switch/Circuit Breaker – Main Power Input
3.2A Fuse (Slow-Blow) – Field Output
4A Circuit Breaker – Control Functions
Communication Modem (optional): 3/4A (Fast-Blow)
Pump/Common & Communication Surge Protection
Module (optional): 1/2A (Fast-Blow)
1
Selecting Control Options
A set of eight DIP switches, located beneath the upper left corner of the control panel (as illustrated below)
is provided for the selection of optional control characteristics. Power to the controller must be turned Off
and the control panel removed from the cabinet in order to make switch position changes. When power is
switched on, the controller will automatically reconfigure to the new switch settings (with the exception of
switch 5). See *Note below.
The controller is shipped from the factory in the following configuration:
Switch 1 ON and Switch 2 ON – Enables the controller to run eight programs concurrently.
• Option – Switch 1 OFF and Switch 2 ON – Enables the controller to run only six programs
concurrently.
• Option – Switch 1 OFF and Switch 2 OFF – Enables the controller to run only four programs
concurrently.
• Option – Switch 1 ON and Switch 2 OFF – Enables the controller to run only two programs
concurrently.
Switch 3 ON – Time is displayed in a.m./p.m. format.
• Option – Switch 3 OFF – Time is displayed in 24-hour format (00:00–23:59)
Switch 4 ON – Pump output activates at the same time as station output.
• Option – Switch 4 OFF – Pump output starts 5 seconds prior to station output. (Enables pump to reach
pressure prior to station operation.)
Switch 5 ON – Active day change occurs at midnight (12:00 a.m.[00:00])
• Option – Switch 5 OFF – Day change occurs at 6:00 a.m. (06:00)
*Note: This change requires initialization to activate. See page 14 for initialization procedure.
Switches 6, 7 & 8 are non-functional.
To change the DIP switch positions:
1. Switch the power Off at controller power supply.
2. Remove the timing mechanism from the top of the pedestal cabinet. (The cables attached to the timing
mechanism can remain connected for this procedure).
3. Locate the DIP switches mounted on top left corner of timing mechanism PCB.
4. Using a pen tip or small screwdriver, reset the DIP switches as required. (Do not use a pencil for this
procedure. Loose graphite from the pencil can damage the switch mechanism).
5. Reinstall the timing mechanism and switch on the power.
Central
Address
Programs
Time/Day
%
Adjust
Stand
Alone
Off
Run
Cycle
Times
Start
Syringe
Times
Active
Days
Tu
Multi
Manual
1
2
3
4
5
1
6
7
8
9
10 11 12 13 14
Week
Week
2
ENTER
START
EXIT
STOP
R
TM
LTC Plus
8
7
6
5
4
3
2
1
OFF
ON
3
Before Programming the Controller…
Please note the following important information before programming the Network LTC Plus con-
troller for the first time. Although the controller is quite easy to program, it does have some pro-
gramming and operating characteristics which will be helpful to know before starting.
• *If power is interrupted to the satellite within one minute of a programming entry, the controller memory
will be initialized (erased) when power is restored.
• An audible “beep” tone occurs whenever a control panel key is pressed sufficiently. If the tone is not
emitted, the key’s function will not be recognized.
• Programming can only be accomplished in the Central or Stand Alone control modes.
• The
and
(cursor keys) are used to navigate to the various program elements of the displays.
When an element is selected, it begins flashing. Remember, a program element must be flashing
before it can be changed.
• The
and
(scroll keys) are used to scroll forward or backward through the program element
values Holding either of these keys down for more than two consecutive seconds will initiate rapid
scrolling.
ENTER
• The
(Enter/Start key) must be pressed to enter a program change into memory.
(function select) key to select the Time/Day mode.
START
• To exit a programming procedure, press the
• During programming, the controller will automatically revert to Time/Day mode if a control panel key is
not pressed for one minute.
About the Controller’s Memory…
The controller utilizes a special “Super Cap” capacitor which stores enough power to maintain the current
time/date and the currently active program information for approximately 30 minutes. The controller will be
otherwise inactive during the power outage. In most circumstances, the user-defined program information is
unaffected by a loss of power and is stored in memory for several years. (See * above). When power is
restored, any automatic programs operating prior to the power failure will resume from the point of interrup-
tion. Any manually started programs operating prior to the power failure will be canceled. Any automatic start
times originating from the satellite or the central during the power failure will be ignored. In regions with fre-
quent power interruptions, an optional lithium battery can be installed which will sustain real time and cur-
rently active program information for approximately 90 days of continuous duty. See “Battery Installation” on
page 16 for more information.
Set Satellite Operating Mode
Selecting one of three operating modes determines how the satellite will operate.
Central mode enables two-way communication between the satellite and the central controller. The satellite
receives all operating commands (including the current time and day) from the central. No additional pro-
gramming is required at the satellite. To operate in the Central mode, the satellite only requires an address
which enables the central to locate it on the communication path. See “Set Satellite Address” on page 13.
Stand Alone mode enables the satellite controller to operate independently from the central. Any data
downloaded from the central will be ignored by the satellite while in this mode. However, information regard-
ing field status and manual satellite operations will be uploaded to the central. When operating as a stand-
alone controller, the Network LTC Plus maintains 16 independent watering programs. Each program is given
specific operating information consisting of: Start Times – when and how often the program will start,
Active Days – the daily watering routine in either a 14-Day Calendar or 29-Day Interval schedule, and Run
Times – the operating duration time of each station assigned to the program. During a program event,
stations assigned to the program operate one at a time in numerical sequence.
Off mode terminates and prevents all automatic and manual controller operations.
If programming the satellite for stand-alone operation, we recommend that you first plan out your irrigation
schedule using the Program Data Reference Form provided on the back cover. Make photocopies of the
form for each program you intend to use. Organizing your program information in this way will provide a
complete overview of your automatic irrigation schedule and simplify the programming task. After the forms
have been filled in, keep them with the satellite for future reference.
1. Press the
key as needed to select the Central, Stand Alone, or Off indicator.
4
Set Current Time and Day
Synchronizing the controller's clock with the current time and day is an important first step in the programming
procedure. The timed events for all watering programs (when the satellite is in the Satellite Mode) are based on
the settings you will make here.
Use the following procedure to set the current time and day:
:
AM
1. Press
as needed to select Time/Day indicator.
2. Press
– The hour digit(s) will begin flashing.
:
3. Press
or
to increase or decrease hour digit(s).
Mo
(Observe for correct a.m./p.m. time.)
4. Press – Minute digits will begin flashing.
or to increase or decrease minute digits.
1 2 3 4 5 6 7
Week 2
Example: Current Time 11:28 A.M.,
Current Day Tuesday (10) Week 2.
5. Press
6. Press
7. Press
– Day abbreviation will begin flashing.
:
AM
Tu
or
ENTER
to select current day in either week of 14-day cycle.
to store new information into controller memory.
1 2 3 4 5 6 7
Week 1
8 9 10 11 12 13 14
Week 2
8. Press
START
Set Station Run Time
Note the following Station Run Time characteristics:
•
•
Run time can be set from one minute to eight hours and 59 minutes in one-minute increments.
Each station can have a different assigned run time within each of 16 programs.
1. Press
to select the Programs indicator. The Run Time
indicator will light. The program and station number will be shown in the
left display, and the station run time will be shown in the right display.
Run Time
Program No.
:
:
2. Press
or
to select the desired program number (1–16).
Note: If the station run time has been adjusted to a value other than 100%
using the % Adjust feature, the right display will alternate between the
programmed run time and the adjusted run time. The % Adjust LED will
light momentarily when the adjusted run time is displayed.
Hours
Station No.
Minutes
Example Shown: Program 1, station 2, run time 1 hour and 23 minutes.
3. Press
– The station number digits will begin flashing.
or to select the desired station number
:
:
:
4. Press
Note: The controller will automatically determine the number of station
modules installed and limit the display accordingly.
5. Press
flashing.
6. Press
to select the run time display. The hours digit will begin
:
or to select the desired hours of run time (0–8).
Note: If station operation is not desired during a particular program,
enter 0:00 run time.
7. Press
– The minutes digits will begin flashing.
8. Press
or
to select desired minutes of run time (0–59).
:
:
ENTER
9. Press
to enter the information.
START
10. Repeat steps 4–8 for each station as required.
11. Press – Repeat steps 2–11 for all programs.
5
Set Program Start Time(s)
This procedure will determine when each program will start during a 24 hour period. Note the following
characteristics:
• Each program can have from 1 to 12 start times.
• Start times can be set to the minute.
• Program operation can be prevented for any of the 12 start times by selecting OFF (no start time).
• When operating in the Stand Alone mode, any new start times downloaded from the central will be ignored.
• When operating in the Central mode, new start times downloaded from the central will be utilized.
1. Press
as needed to select the Program indicator.
Start Time No.
Program No.
2. Press
3. Press
4. Press
to select the Start Time indicator.
Current
Start Time
or
to select the desired program number (1 – 16).
:
:
– Start time 01 will begin flashing and current start time
will be shown.
5. Press
6. Press
7. Press
or
– Hours digit(s) or “OFF” will begin flashing.
or to adjust hours digits up or down.
to select desired start time number (1 – 12).
:
:
(Observe for correct a.m./p.m. time.)
AM
Note: If no start time is desired, select "OFF" – located between
11 p.m. and 12 a.m. (23:00 and 00:00). Skip steps 8 & 9 and
continue at step 10.
Example shown: Program 1, start time 1 set to 2:30 a.m.
8. Press
– Minutes digits will begin flashing.
9. Press
or
to adjust minutes digits up or down.
to enter the information.
:
:
AM
ENTER
10. Press
START
11. Repeat steps 5 – 10 for all desired start times for this program.
12. Press
to select another program number.
13. Repeat steps 3 – 12 as required.
6
Set Active Day Watering Schedules
The active watering days for each program can be chosen using a Calendar schedule or an Interval
schedule. The Calendar schedule enables active days to be selected within a 14-day (two week) cycle. The
Interval Schedule enables active days to be selected by a specific interval, such as every day, every-other
day, every-third day and so on – up to every twenty-ninth day.
Select the active watering days for each program using either a Calendar schedule (below) or an Interval
schedule (on page 8).
Note the following programming characteristics:
• Only one watering day schedule (Calendar or Interval) can be utilized for each program.
• To prevent automatic operation of any program, all days in a Calendar Schedule can be deleted or
Interval Day can be set to Off.
To Set a Calendar schedule:
Schedule Type
(Calendar)
1. Press
as needed to select the Program indicator.
Program No.
2. Press
to select the Active Days indicator.
:
:
:
3. Press
or
until the desired program number (1 – 16) is
flashing.
4. Press
5. Press
6. Press
– The schedule type will begin flashing.
or
until CA (Calendar) is flashing.
– The current Calendar schedule is displayed and
Sunday (Su) of week 1 is flashing.
We
Fr
We
Mo
Su
Mo
Fr
1 2 3 4 5 6 7
Week 1
8 9 10 11 12 13 14
Week 2
7. Choose to select or delete the indicated (flashing) day.
• To select: Press – The day stops flashing and remains
displayed and the next day starts flashing.
• To delete: Press
– The day disappears and next day starts
flashing.
8. Repeat step 7 to set the 14-day watering schedule.
Note: To prevent automatic operation of the program, delete all 14
days or, as an alternate method, select Interval “Off”. See page 8 for
this procedure.
ENTER
9. Press
to enter the information into controller memory.
START
10. Repeat steps 3 – 9 for all programs requiring a Calendar
schedule.
Note: If an Interval watering schedule is not required, programming
for automatic operation is now complete. When an automatic program
starts, the displays will alternate between the time/day and program
status. If two or more programs are operating concurrently, the display
will alternate to show status of each program.
:
AM
Fr
:
:
Pgm #
Sta Run Time
Sta #
7
Interval Schedule
Scheduling active days by Interval enables a program to operate on a specific routine such as, every other
day, or every fourth day, without regard to actual calendar days.
The Interval schedule consists of two programmable numbers: The Interval Reference and the Interval Day.
The Interval Reference number (01 – 29) determines how often an active watering day will occur. For
example, entering 01 equals watering every day, 02 equals every other day and so on up to 29 for watering
every 29th day. The Interval Day number (01 – 29 and Off) indicates when an active watering day will occur.
The Interval Day number automatically decreases by one at the day changeover. An active watering day will
occur when the Interval Day number is 01. As the day change occurs at the end of the active watering day,
the Interval Day number will automatically update to display the number of days until the next active
watering day.
During initial programming, the Interval Day number can be set at any point in the interval to establish the
position of the interval within the week or month. For example, you may select a 6-day interval (watering
every sixth day) but choose to start the interval tomorrow by entering an Interval Day number of 02. After
one day has elapsed, the interval will begin and the day will be active. At the end of the active day, the
Interval Day number will reset to 06, indicating six days until the next scheduled watering.
Note: The Interval Day number cannot be greater than the interval reference number. If attempted, the
Interval Day number will automatically be reduced to equal the the Interval Reference number when the
Enter/Start key is pressed.
To set an Interval schedule:
Schedule Type
1. Press
as needed to select the Program indicator.
(Interval)
Program No.
2. Press
to select the Active Days indicator.
:
Interval
3. Press
or
until the desired program number (1 – 16) is
Reference No.
flashing.
4. Press
– The schedule type will begin flashing.
:
:
:
5. Press
or
–The Interval Reference digits will begin flashing.
or to select desired Interval Reference number
until In (Interval) is flashing
:
6. Press
7. Press
(01 – 29).
:
:
8. Press
– Interval Day number will begin flashing.
or to select Interval Day (01 – 29).
9. Press
Example Shown: Watering every third day (03),
starting tomorrow (02).
Note: To prevent automatic operation of this program, select Off
located between 00 and 29.
:
ENTER
10. Press
to enter information into controller memory.
START
11. Repeat steps 3 – 10 for each program requiring an Interval
schedule.
Note: Programming for automatic operation is now complete. When
an automatic program starts, the displays will alternate between the
time/day and program status. If two or more programs are operating
concurrently, the display will alternate to show status of each program.
:
:
AM
Fr
:
Pgm #
Sta Run Time
Sta #
8
Set Program Repeat and Soak
This is an optional programming feature which enables a program to repeat its operating cycle from 0 – 3
times (in addition to its initial cycle). A soak-in period from 0 – 59 minutes is placed between repeat cycles.
Program No.
1. Press
as needed to select the Program indicator.
or until the desired program number (1 – 16) is
Station No.
2. Press
:
:
flashing.
3. Press
4. Press
5. Press
– 01 will begin flashing.
No. of Repeats
– The letter "r" (repeat) will begin flashing.
Repeat
– The digit left of colon in the right side display will
:
begin flashing.
6. Press
7. Press
8. Press
or
– The digits right of colon will begin flashing.
or to select a soak time (0 – 59 minutes).
to display desired number of repeats (0 – 3).
:
:
:
Example Shown: Program 1, 2 repeat cycles with a 10-minute soak
time between cycles.
2 Repeats
Program 1
ENTER
10 minutes
Soak Time
9. Press
to enter information into controller memory.
START
10. Press
– The Program number will begin flashing.
:
11. Repeat steps 2 – 10 for all programs as required.
AM
Fr
Note: During the soak period between watering cycles, the displays
will alternate between Time/Day and Repeat/Soak status.
:
:
Program No.
Repeats
Remaining
Soak Time
Remaining
9
Program Operation Pause and Cancel
An operating program can be paused or canceled at any time as needed. The pause feature temporarily
suspends program operation for up to 10 minutes. When operation resumes, the program continues from
the point of interruption without loosing station run time. Use the cancel feature to terminate the program
operation, returning the controller the the time and day mode.
EXIT
To pause program operation: Press the
key while the program status is displayed. The right side
STOP
display will show a letter P indicating the program is Paused.
Note: Program operation will resume automatically in 10 minutes if the Enter/Start key is not pressed.
ENTER
To resume program operation: Press the
key.
START
EXIT
To cancel program operation: Either press the
key two times, or press the
key to select Off,
STOP
thenpress the key again as needed to select Central or Stand Alone mode.
Manual Control Operations
Manual operations can be initiated at any time and can occur concurrently with automatically started watering
operations. Three types of manual operations are available:
• Cycle mode to start complete or partial program cycle(s)
• Syringe mode to enable all stations in a program to be operated for a temporary run time from
1 – 30 minutes or 10 – 99%
• Multi-Manual mode to provide simultaneous operation of up to 6 stations.
Cycle Mode
This mode enables you to start and run all or part of any automatic watering program. Full Cycle runs a
complete cycle of any program selected. Partial Cycle starts the program cycle at any selected station, and
runs only the stations (with programmed run time) which follow in the program cycle.
Note: During a manual operation, all programmed repeat and soak operations will be ignored.
I Full Cycle
1. Press
to select the Cycle indicator.The Program indicator will light and program 1 will be
automatically selected.
2. Press
or
until the desired program number (1 – 16) is flashing.
ENTER
3. Press
to start the program watering cycle.The displays will alternate between the Time/Day and
program status displays.
START
4. To start additional programs, repeat steps 2 – 3.
Note: The maximum number of programs which can operate concurrently during manual operation is 4.
I Partial Cycle
1. Press
to select Cycle indicator. Program 1 will be automatically selected.
2. Press
or
until the desired program number (1 – 16) is flashing.
3. Press
– The first station number with a run time in the selected program will begin flashing.
4. Press
or
as required to select the station number to begin the partial cycle.
ENTER
5. Press
to start the program watering cycle.The displays will alternate between the Time/Day and
START
program status displays.
10
Syringe Mode
The Syringe mode enables all stations with a programmed run time in a selected program to be operated for
a short, temporary run time (syringe). The amount of run time for the syringe operation can be set from
1 – 30 minutes or by a percentage of programmed station run time from 10% – 99%.
To syringe all stations from 1 – 30 minutes:
Program
1. Press
automatically selected .
2. Press or to select desired Program number (1 – 16).
to select Syringe indicator.Program 1 will be
Number
Run Time In
Minutes
Syringe
Run Time
The Left display shows the program number and rt (run time in
minutes). A 1-minute syringe time is automatically selected and shown
in the right display. To increase the syringe run time, continue at step 3.
If no increase is needed, continue at step 5.
:
:
:
3. Press
– The syringe time digits will begin flashing.
4. Press
or
to select a syringe time (02 – 30 minutes).
ENTER
5. Press
to start the syringe cycle. The displays will alternate
:
:
AM
START
between the time/day and the program status.
Fr
Note: Only the stations with a programmed run time in the program
selected will operate during the syringe operation.
:
Station
Number
Syringe
Time
Program
Number
Remaining
To syringe from 10% – 99% of station run time:
Program
Number
1. Repeat steps 1 and 2 above.
Run Time By
Percentage
25%
2. Press
The left display shows a % symbol. A 25% adjusted run
time value is automatically selected and shown in the right display.
To change the % value, continue at step 4; if no change is needed,
continue at step 6.
:
3. Press
– Syringe % value (25%) will begin flashing.
4. Press
or
to adjust run time value from 10% – 99%.
ENTER
5. Press
to start the syringe cycle. The displays will alternate
START
between Time/Day and program status as shown above.
Adjusted Run
Time % Value
Note: When the station run time remaining becomes less than one
minute, the display will show 00. The display will continue to show 00
while the remaining time of 59 seconds or less elapses.
11
Multi-Manual Mode
Up to six selected stations can be operated at the same time using Multi-Manual mode. A temporary run
time from 1 to 59 minutes is given to each station for this operation.
Caution: Prior to Multi-Manual operation, ensure that combined current draw of all stations operating
at the same time (including pump relay) does not exceed 3.2 Amps (holding).
1. Press
to select the Multi-Manual indicator. The Program
Station Number
Run Time
indicator will light and Station number 01 will be shown (flashing)
in the left display.The right display will show 00 run time.
:
2. Press
3. Press
4. Press
or
as needed to select the desired station.
– The Run Time digits will begin flashing.
or
as needed to select desired Run Time (01 – 59)
:
ENTER
5. Press
– Selected station will start.
START
6. Repeat steps 2 – 5 to start up to five additional Stations. If the
same run time is desired, skip steps 3 and 4.
Note: Any additional stations entered while six stations are in
operation will be ignored.
Note: After 1 minute has elapsed, the displays will begin alternating
between the time/day and the program status, showing (in sequence)
each operating station and its remaining run time.
:
AM
Fr
:
:
:
12
Set Satellite Address
The LTC satellite requires a unique address for identification by the central LCM within the network system. The
address consists of a group number (1 – 50) and satellite number (1 – 500). A combination of up to 500 satellites
may be defined. Satellites may only be assigned to one group. However, the same satellite number may be
used for satellites in different groups. For example, satellite 001 in group 01 has a different address than satellite
001 in group 04. The satellite address is based on the combination of the group and satellite numbers.
Use the following procedure to assign the satellite address.
1. Press
to select Address indicator The displays show the
current group and satellite numbers. The default address is group
50, satellite 500.
Group
Number
Controller
Number
2. Press
– Group number will begin flashing.
or to select desired group number (01 – 50).
– Satellite number will begin flashing.
3 Press
4. Press
5. Press
or
to select desired satellite number (01 – 500).
ENTER
6. Press
to enter the information.
START
Set Percent Adjust
This feature enables the run time of all stations assigned to a program to be adjusted by the same
percentage up or down in 1% increments. Run time percent adjustments can be applied to individual
programs and/or globally to all programs.
Note the following Percent Adjust characteristics:
• Adjustable from 10% to 250% (100% is neutral position).
• Adjusted station run time is displayed during program operation and while setting station run times.
(See Note on page 5 regarding adjusted run time display.).
• % adjust values will be reset to 100% when operated in the Central control mode.
• Global adjust (P0) is applied to all programs in addition to individual program % adjust value.
Example: A 40 minute run time with a 50% Individual program adjust value and 50% Global adjust value
equals 10 minutes adjusted run time (40 x 50% = 20 x 50% = 10).
1. Press
to select % Adjust indicator. The displays show P0
Global Adjust
(All Programs)
(Global adjust) and current % value. If global adjustment is desired,
continue at step 3. If Global adjust is not desired, continue at step 2.
100%
2. Press
3. Press
4. Press
or
– The percentage digits will begin flashing.
or to adjust the percentage up or down.
as needed to select desired program number.
Note: For programs P1 – P16, an OFF position is provided between the
250% and 10% change point. Selecting OFF prevents the program from
being affected by a global % adjustment and locks the program % adjust
value at 100%.
Program
Number
120%
ENTER
5. Press
to enter the information.
START
6. Repeat steps 2 – 5 for all programs as required.
13
Reviewing Program Information
To review the current operating information entered for any program, use the procedure below. If you need
to make changes to any portion of a program or the Time/Day setting, refer to the appropriate procedure in
the programming section of this manual.
1. Press
to select the Program number indicator.
2. Press
or
as needed to select the desired program number (1 – 16).
3. Press
to select the desired portion of program.
4. Press
or
or
as needed to step through program information.
Special Functions
Note: Station/pump outputs will be momentarily cycled on and off several times during the self test and
Initialization procedures. To prevent possible operation of irrigation valves and pump relay, remove the 3.2A
fuse or disconnect the field common wire(s) until the test is completed.
III
Self Test
The Self Test enables the LTC satellite to automatically perform a diagnostic check of all functions, LED
indicators, LCD elements, internal circuits and station/pump outputs.
To perform the self test:
1. Turn off power supply switch.
2. Press and hold
key down while switching power on. Continue holding key down for 5 seconds,
then release.
During the first portion of the test, the displays will momentarily show the following information:
• Software version installed (i.e., version 1.0 = 1 0)
• Number of stations installed (i.e., 16 stations = 16 STA)
• Diagnostic code (i.e., 00 000)
• Memory chip number (i.e., EE1)
Note: If the memory chip or timer chip is not functioning properly, EE1 Err or CLK Err will be displayed.
The next portion of the test cycles all LED indicators and LCD elements and turns the station/pump outputs
on and off.
3. To end self test, press
and
keys simultaneously. Current time will be displayed (flashing). Press
EXIT
the
key to stabilize display.
STOP
III
Initialization
Note: Performing an initialization permanently erases all user defined program information from the
satellite memory (except current time and day).
To perform an initialization:
1. Turn off power supply switch.
2. Press and hold
key down while switching power on. Continue holding key down for 5 seconds,
then release.
Note: The satellite will perform the same operation as the Self Test (as detailed above), however during the
process all user defined information stored in the memory will be erased.
3. To end initialization process, press
and
keys simultaneously. Current time will be displayed
EXIT
(flashing). Press the
key to stabilize display.
STOP
14
Radio Calibration Test
The radio calibration test enables the LTC to generate three different radio test patterns for use in radio
network communications setup. If a radio is not connected, no indication is seen on the TM. The test
patterns can be monitored by connecting an oscilloscope or headphones to the modem 2-wire connector.
To Perform Radio Calibration Test:
1. Turn off power to controller at power supply switch.
2. Press and hold
key while switching on the power. Continue holding down the key for 5 seconds.
The left display will show CAL.
3. Wait 30 seconds
• Press
– A 1200 Hz test pattern will be generated for 30 seconds.
• Press
– A 2200 Hz test pattern will be generated for 30 seconds.
ENTER
• Press
– An alternating 1200/2200 Hz test pattern will be generated for 30 seconds.
START
EXIT
4. Press
to exit Radio Calibration Test mode.
STOP
Link Monitor
Link Monitor enables any satellite communicating with the central to review the communications link status
of all satellites within the network. During Link Monitor operation, the central continuously polls the network
satellites in numerical sequence and rapidly displays the addresses accompanied by an audible “beep”. If a
satellite does not respond to the central during the polling process, the satellite address remains displayed
for two seconds and is accompanied by two additional beeps. After all satellites have been polled, the last
satellite address in numerical sequence remains displayed for ten seconds. The polling sequence is
repeated continuously until the Link Monitor is exited by pressing the Exit/Stop key.
1. Press and hold down the
key for five seconds to activate
Group #
Satellite #
Link Monitor mode.
Note: If this satellite is not connected to the network or if the LCM
is not polling, 00 000 will be displayed.
EXIT
2. Press the
key to exit the Link Monitor mode.
STOP
15
Troubleshooting
If you experience a controller problem, check the programming for a possible programming error and the
list of problems and solutions listed below. If the problem continues, contact your local Toro distributor
for assistance.
WARNING
TO AVOID ELECTRICAL SHOCK HAZARD, ASSURE POWER SOURCE IS OFF BEFORE
ATTEMPTING ANY CONTROLLER REPAIR. ALL REPAIRS SHOULD BE PERFORMED BY A
QUALIFIED TECHNICIAN.
Problem
Probable Cause
Remedy
I Controller inactive — no display
1. 4A control circuit breaker tripped.
1. Check output module switches. Set
ALL switches to Auto or Off. Reset
4A circuit breaker.
2. Power supply On/Off switch in
Off (O) position.
2. Position switch in On (–) position.
1. Improper valve connection(s).
2. Station output module switch in Off
position.
1. Check connections.
2. Set output module switch to Auto
position.
I Controller on — valve(s) not
operating
3. 3.2A fuse blown.
3. Replace 3.2A fuse
I Pump does not operate
1. Pump output module control switch
in Off position.
1. Set control switch to Auto position
2. Pump component malfunction.
2. Repair or replace faulty pump
components.
3. Improper pump connection(s).
1. DIP switch #1 and #2 position.
3. Check connections.
1. Check position of DIP switch #1 &
#2. See page 3.
I Limited number of programs can
be operated at a time
I a.m. or p.m. designation does not
1. DIP switch #3 in Off position —
time displayed in 24-hour format.
1. Set DIP switch #3 to On position.
See page 3.
appear with clock time
Lithium Battery installation (optional)
An optional 3.9V lithium battery (P/N 363-2200) can be installed to sustain the controllers clock time and the
currently active program information for approximately 90 days with no additional power applied.
WARNING
DANGER OF EXPLOSION IF BATTERY IS INSTALLED INCORRECTLY. REPLACE ONLY WITH
THE SAME OR EQUIVALENT TYPE OF BATTERY. ALWAYS DISPOSE OF USED BATTERIES
ACCORDING TO THE BATTERY MANUFACTURER’S INSTRUCTIONS.
Procedure
1. Turn off power to controller at power supply switch.
2. Remove phillips screws from corners of control panel and
carefully lift panel up.
3. Turn control panel over, resting it face down on pedestal.
Connector cables can remain attached to PCB for this
procedure.
4. Remove five phillips screws from back of control panel
PCB and separate PCB from faceplate assembly.
5. Locate battery pin sockets located on front side of PCB
as shown at right. Insert battery carefully to avoid bending
contact pins. The pins are unevenly spaced allowing the
battery to be installed easily in one direction only. Do not
force battery pins into sockets. See Warning above.
6. Reassemble control panel assembly and reinstall into
pedestal.
7. Restore power to controller at power supply switch.
16
Manual Output Switch Operation
A 3-position switch is provided on the Pump/Com
module for additional control of the pump relay
circuit. In addition, the optional station terminal
modules with optional control switches have one
switch for each station output.
Field Common
Engage Switch
Field Common
Indicator Lamp
The three switch positions control the circuits as
follows:
On – Manually activates the circuit. The pump or
station will remain on until the switch is moved to the
Auto or Off position.
Pump Circuit
Switch
HOT POST
HOT POST
H
Off – Switches the circuit off, preventing pump or
station operation from the satellite.
Station Output
Control Switches
(Optional)
Auto – The circuit is automatically activated by the
controller during automatic or manual watering
operation.
As an added lightning protection measure, the field
common circuit is normally open when the controller
is inactive. Therefore, to use the field output control
switches for manual operation, the common circuit must be engaged first. Press the Field Common
Engage push button switch to activate the circuit. The Field Common Indicator Lamp will turn on when the
circuit is active. The common circuit will automatically disconnect upon completion of an automatic or
manually activated watering operation initiated through the timing mechanism. The circuit can also be
disconnected by momentarily switching the power supply off.
Caution: To prevent damage to the 3.2A field output circuit fuse, do not exceed 3.2A load when
manually activating multiple field outputs.
Power Indicator Lamps
Two indicator lamps, as shown in the illustration at
right, are provided to verify the presence of power to
the control and field output circuits. In normal
Control Circuit
Indicator Lamp
Indicator Lamp
Output Circuit
operating conditions, both lamps will be On. If both
lamps are Off, no power is present. Ensure the
power supply/circuit breaker switch is On. Also
check the main power source circuit breaker and
any additional power disconnection devices in the
fixed wiring. If the left indicator lamp is Off, the 4A
circuit breaker is open and must be reset. If the right
indicator lamp is off, the 3.2A field output fuse is
blown.
8-Station Module
Retainer Screw
WARNING
IF FUSE REPLACEMENT IS REQUIRED,
REPLACE WITH A FUSE OF THE SAME
TYPE AND AMPERAGE RATING. FAILURE
TO COMPLY CAN RESULT IN SERIOUS
INJURY AND/OR EQUIPMENT DAMAGE
DUE TO FIRE HAZARD.
Power Supply
On/Off Switch
4A Control
Circuit Breaker
Removing and Installing 8-Station Modules
1. Switch power supply Off
3.2A Field
Output Fuse
Power Supply 5A
Circuit Breaker
2. Remove single screw from module.
3. Pull module outward from top connector then
upward from bottom connector (if installed).
4. Install module in reverse order.
Note: When adding modules, utilize the first available open position from left to right, front to back. Do
not leave open spaces between modules.
17
Program Data Reference Form
Program Number_____ Date_________
Station Location
1 ___________________ 17 ___________________ 33____________________ 49____________________
2 ___________________ 18 ___________________ 34____________________ 50____________________
3 ___________________ 19 ___________________ 35____________________ 51____________________
4 ___________________ 20 ___________________ 36____________________ 52____________________
5 ___________________ 21 ___________________ 37____________________ 53____________________
6 ___________________ 22 ___________________ 38____________________ 54____________________
7 ___________________ 23 ___________________ 39____________________ 55____________________
8 ___________________ 24 ___________________ 40____________________ 56____________________
9 ___________________ 25 ___________________ 41____________________ 57____________________
10 ___________________ 26 ___________________ 42____________________ 58____________________
11 ___________________ 27 ___________________ 43____________________ 59____________________
12 ___________________ 28 ___________________ 44____________________ 60____________________
13 ___________________ 29 ___________________ 45____________________ 61____________________
14 ___________________ 30 ___________________ 46____________________ 62____________________
15 ___________________ 31 ___________________ 47____________________ 63____________________
16 ___________________ 32 ___________________ 48____________________ 64____________________
Station Run Time (1 minute to 8 hours 59 minutes)
Sta. 1 ___ hrs. ___ min.
Sta. 2 ___ hrs. ___ min.
Sta. 3 ___ hrs. ___ min.
Sta. 4 ___ hrs. ___ min.
Sta. 5 ___ hrs. ___ min.
Sta. 6 ___ hrs. ___ min.
Sta. 7 ___ hrs. ___ min.
Sta. 17 ___ hrs. ___ min.
Sta. 18 ___ hrs. ___ min.
Sta. 19 ___ hrs. ___ min.
Sta. 20 ___ hrs. ___ min.
Sta. 21 ___ hrs. ___ min.
Sta. 22 ___ hrs. ___ min.
Sta. 23 ___ hrs. ___ min.
Sta. 33 ___ hrs. ___ min.
Sta. 34 ___ hrs. ___ min.
Sta. 35 ___ hrs. ___ min.
Sta. 36 ___ hrs. ___ min.
Sta. 37 ___ hrs. ___ min.
Sta. 38 ___ hrs. ___ min.
Sta. 39 ___ hrs. ___ min.
Sta. 49 ___ hrs. ___ min.
Sta. 50 ___ hrs. ___ min.
Sta. 51 ___ hrs. ___ min.
Sta. 52 ___ hrs. ___ min.
Sta. 53 ___ hrs. ___ min.
Sta. 54 ___ hrs. ___ min.
Sta. 55 ___ hrs. ___ min.
Sta. 8 ___ hrs. ___ min.
Sta. 24 ___ hrs. ___ min.
Sta. 40 ___ hrs. ___ min.
Sta. 56 ___ hrs. ___ min.
Sta. 9 ___ hrs. ___ min.
Sta. 25 ___ hrs. ___ min.
Sta. 41 ___ hrs. ___ min.
Sta. 57 ___ hrs. ___ min.
Sta. 10 ___ hrs. ___ min.
Sta. 11 ___ hrs. ___ min.
Sta. 12 ___ hrs. ___ min.
Sta. 13 ___ hrs. ___ min.
Sta. 14 ___ hrs. ___ min.
Sta. 15 ___ hrs. ___ min.
Sta. 16 ___ hrs. ___ min.
Sta. 26 ___ hrs. ___ min.
Sta. 27 ___ hrs. ___ min.
Sta. 28 ___ hrs. ___ min.
Sta. 29 ___ hrs. ___ min.
Sta. 30 ___ hrs. ___ min.
Sta. 31 ___ hrs. ___ min.
Sta. 32 ___ hrs. ___ min.
Sta. 42 ___ hrs. ___ min.
Sta. 43 ___ hrs. ___ min.
Sta. 44 ___ hrs. ___ min.
Sta. 45 ___ hrs. ___ min.
Sta. 46 ___ hrs. ___ min.
Sta. 47 ___ hrs. ___ min.
Sta. 48 ___ hrs. ___ min.
Sta. 58 ___ hrs. ___ min.
Sta. 59 ___ hrs. ___ min.
Sta. 60 ___ hrs. ___ min.
Sta. 61 ___ hrs. ___ min.
Sta. 62 ___ hrs. ___ min.
Sta. 63 ___ hrs. ___ min.
Sta. 64 ___ hrs. ___ min.
Start Times:
1. ____________ am / pm
2. ____________ am / pm
3. ____________ am / pm
4. ____________ am / pm
5. ____________ am / pm
6. ____________ am / pm
7. ____________ am / pm 10. ____________ am / pm
8. ____________ am / pm 11. ____________ am / pm
9. ____________ am / pm 12. ____________ am / pm
Program Repeat:
II 0
I 1
I 2
I 3
Soak Time (0–59 minutes) ____ Minutes
Active Day Schedule:
Calendar Week 1 I Su-1 I Mo-2 I Tu-3 I We-4 I Th-5 I Fr-6 I Sa-7
Week 2 I Su-8 I Mo-9 I Tu-10 I We-11 I Th-12 I Fr-13 I Sa-14
Interval
I 01
I 02
I 03
I 04
I 05
I 06
I 07
I 08
I 09
I 10
I 11
I 12
I 13
I 14
I 15
I 16
I 17
I 18
I 19
I 20
I 21
I 22
I 23
I 24
I 25
I 26
I 27
I 28
I 29
© 1998 The Toro Company
Irrigation Division
An ISO-9001-Certified Facility
P.O. Box 489 Riverside, CA 92502
Printing Date
August 1998 - Rev C
Form Number
371-0011
Network LTCTM Plus
Series Satellite
U s e r ' s G u i d e
R
TM
|