MC-780PIx CCD Camera
User’s Guide
SOCU006
July 1998
Printed on Recycled Paper
Preface
Read This First
About This Manual
This User’s Guide describes the characteristics and operation of the
MC-780PIA and MC-780PIH CCD Video Camera Modules.
How to Use This Manual
Use this manual for technical data, operating characteristics, and general fa-
miliarization with the products before, during, and after installation.
Information About Cautions and Warnings
This book may contain cautions and warnings.
This is an example of a caution statement.
A caution statement describes a situation that could potentially
damage your software or equipment.
This is an example of a warning statement.
A warning statement describes a situation that could potentially
cause harm to you.
The information in a caution or a warning is provided for your protection.
Please read each caution and warning carefully.
iii
If You Need Assistance
If You Need Assistance . . .
If you want to . . .
Contact Texas Instruments at . . .
Visit TI online
Receive general information
or assistance
North America, South America: (214) 644–5580
Europe, Middle East, Africa
Dutch: 33–1–3070–1166
English: 33–1–3070–1165
French: 33–1–3070–1164
Italian: 33–1–3070–1167
German: 33–1–3070–1168
Japan (Japanese or English)
Domestic toll-free: 0120–81–0026
International: 81–3–3457–0972 or
81–3–3457–0976
Korea (Korean or English): 82–2–551–2804
Taiwan (Chinese or English): 886–2–3771450
Ask questions about Digital
Signal Processor (DSP)
product operation or report
suspected problems
(713) 274–2320
Fax: (713) 274–2324
Fax Europe: +33–1–3070–1032
Email: [email protected]
BBS North America: (713) 274–2323 8–N–1
BBS Europe: +44–2–3422–3248
320 BBS Online: ftp.ti.com:/mirrors/tms320bbs
(192.94.94.53)
Ask questions about micro-
controller product operation
or report suspected prob-
lems
(713) 274–2370
Fax: (713) 274–4203
Email: *[email protected]
BBS: (713) 274–3700 8–N–1
Request tool updates
Software: (214) 638–0333
Software fax: (214) 638–7742
Hardware: (713) 274–2285
Order Texas Instruments
documentation (see Note 1)
Literature Response Center: (800) 477–8924
Make suggestions about or
report errors in documenta-
tion (see Note 2)
Email: [email protected]
Mail: Texas Instruments Incorporated
Technical Publications Manager, MS 702
P.O. Box 1443
Houston, Texas 77251–1443
Notes: 1) The literature number for the book is required; see the lower-right corner on the back cover.
2) Please mention the full title of the book, the literature number from the lower-right corner of the back cover, and the
publication date from the spine or front cover.
iv
Contents
1
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
1.1
Main Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
1.1.1 High Image Quality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
1.1.2 Mode Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
1.1.3 External Sync . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
1.1.4 Output of Internal Synchronizing Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
1.1.5 Electronic Shutter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Other Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
1.2
2
Nomenclature and Use of Each Component . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
2.1
Mounting System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
2.1.1 Focus Ring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
2.1.2 Mounting Holes A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
2.1.3 Mounting Hole B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
2.1.4 Mounting Holes C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Rear Panel Switches and Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
2.2.1 Shutter Speed Control Switch SW1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
2.2.2 External Synchronization Terminal Resistance Switch SW4 . . . . . . . . . . . . . . . 2-4
2.2.3 Mode Switches SW3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
2.2.4 Gain Mode Switch SW2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
2.2.5 Gain Variable Volume Control VR1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
2.2.6 DC IN Terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
2.2.7 LENS Terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
2.2.8 DC IN/SYNC Terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
Internal Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8
2.3.1 SYNC Signal (HD/VD) Input/Output Switch SW1 . . . . . . . . . . . . . . . . . . . . . . . . . 2-8
2.3.2 Option Output Switch S1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9
2.3.3 Gamma Switch SW1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9
2.3.4 AC/DC Output Switch SW4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10
2.3.5 Outline Emphasis Circuit ON/OFF Switch SW2 . . . . . . . . . . . . . . . . . . . . . . . . . 2-10
2.2
2.3
3
4
Using the External SYNC Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
3.1
External Sync With Interlace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
3.1.1 External Sync Signal Input Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
External Sync With No Interlace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
3.2.1 External Sync Signal Input Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
3.2
Using the Shutter Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
4.1 Continuous Shutter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
v
Contents
4.2
4.3
4.4
4.5
Random Shutter (Fixed V Sync) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
Random Shutter (V Sync Reset) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
VI Mode Shutter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
Precautionary Items . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
5
6
Initial Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
5.1 Modes and Initial Switch Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
Precautions for Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
6.1
Precautions for Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2
6.1.1 Power Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2
6.1.2 Heat Reduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2
6.1.3 Locations for Use and Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3
6.2
7
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
7.1
7.2
Image System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2
Optical Elements and Other Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3
8
9
Exterior Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1
8.1 Exterior Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2
Other Issues . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1
9.1
Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-2
vi
Figures
2–1
2–2
2–3
2–4
2–5
2–6
2–7
2–8
2–9
Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
External Synchronization Terminal Resistance Switch SW4 . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
Gain Mode Switch SW2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
Gain Variable Volume Control VR1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
Internal Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8
SYNC Signal (HD/VD) Input/Output Switch SW1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9
Option Output Switch S1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9
Gamma Switch SW1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9
AC/DC Output Switch SW4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10
2–10 Outline Emphasis Circuit ON/OFF Switch SW2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10
3–1
3–2
4–1
4–2
4–3
4–4
4–5
8–1
External Sync Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
External Sync With No Interlace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
Continuous Shutter Speed-Control Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
Random Shutter Control Timing (Fixed V Sync) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
Random Shutter Control Timing (V Sync Reset) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
VI Mode Shutter Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
Exposure and Transfer Period Conflict With Readout Period . . . . . . . . . . . . . . . . . . . . . . . . 4-6
Exterior Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-3
Contents
vii
Tables
2–1
2–2
2–3
2–4
2–5
2–6
2–7
2–8
2–9
Shutter Speed Control Switch SW1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
External Synchronization Terminal Resistance Switch SW4 . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
Mode Switches SW3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
Shutter list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
Gain Mode Switch SW2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
LENS Terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
DC IN/SYNC Terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
SYNC Signal (HD/VD) Input/Output Switch SW1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8
Option Output Switch S1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9
2–10 Gamma Switch SW1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9
2–11 AC/DC Output Switch SW4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10
2–12 Outline Emphasis Circuit ON/OFF Switch SW2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10
4–1
5–1
7–1
7–2
7–3
Line Corresponding to Shutter Speeds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
Modes and Initial Switch Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
MC–780PIA Image System Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7–2
MC–780PIH Image System Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7–2
Optical Elements and Other Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7–3
viii
Chapter 1
Overview
This User’s Guide describes the operation and characteristics of the
MC-780PIA and MC780PIH video cameras. This chapter gives an overview
of the cameras and their features. Please read and keep this document as a
reference.
Topic
Page
1.1 Main Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
1.6 Other Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
1-1
Main Features
1.1 Main Features
The MC-780PIA and MC-780PIH are black-and-white video cameras that use
fixed-sensor charge-coupled devices (CCDs). The following paragraphs de-
scribe some of the main features of the cameras.
1.1.1 High Image Quality
With 380,000 image-sensing elements, the CCDs reproduce very detailed
images.
1.1.2 Mode Settings
Several modes can be selected depending on the intended use. For example,
using external switches for gain, it is possible to select A (auto adjust), F
(fixed), or M (manual adjust); using the internal switches for γ [gamma] charac-
terisitcs, it is possible to select ON (corrected: γ = 0.45) and OFF (uncorrected:
γ = 1).
1.1.3 External Sync
The camera module can be operated with external sync by inputting HD and
VD signals. Internal or external sync can be selected with the mode switches.
1.1.4 Output of Internal Synchronizing Signals
HD and VD signals can be output by switching their internal switches. Pixel
clock signals and shutter monitor signals can also be selected and output.
1.1.5 Electronic Shutter
A shutter speed can be selected from 1/500 to 1/8000 second to match sens-
ing conditions. It is possible to select continuous shutter, random shutter, or
optional time shutter.
1-2
Overview
Other Features
1.2 Other Features
Long life span, high reliability
Low distortion, high precision image
High near infrared sensitivity
Quick starting
1-3
Overview
1-4
Overview
Chapter 2
Nomenclature and Use of Each Component
This chapter describes the location and use of components, connectors, and
controls.
Topic
Page
2-1 Mounting System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
2-2 Rear Panel Switches and Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
2-3 Internal Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–8
2-1
Mounting System
2.1 Mounting System
The following paragraphs describe the mounting system for the camera
modules.
2.1.1 Focus Ring
C-Mount type lens and optical equipment are installed. If there is difficulty fo-
cusing with the lens, fine adjustments can be made by loosening the two
screws located on the ring. The lens can also be brought back closer to the
CCD by removing the focus ring.
2.1.2 Mounting Holes A
There are four screw holes on the top and bottom for mounting the camera
module. The gauge is M2.6 and the depth is 4.5 mm.
2.1.3 Mounting Hole B
There is a screw hole on the bottom for mounting the camera module. The
gauge is M4 and the depth is 6 mm.
2.1.4 Mounting Holes C
There are screw holes on the bottom for mounting the camera module to a
tripod. The gauge is 1/4UNC and the depth is 6 mm.
2-2
Nomenclature and Use of Each Component
Rear Panel Switches and Terminals
2.2 Rear Panel Switches and Terminals
This paragraph explains the functions of the rear panel switches and termi-
nals. Figure 2–1 shows their locations.
Changing Switch Settings
Always disconnect power when changing the switch settings.
Figure 2–1. Rear Panel
(SW1)
(SW4)
(DC IN)
(SW3)
(VR1)
(SW2)
(DC IN/
SYNC)
(LENS)
2.2.1 Shutter Speed Control Switch SW1
Switch SW1 sets the electronic shutter speed. Table 2–1 shows the shutter
speed settings.
Table 2–1.Shutter Speed Control Switch SW1
Setting No.
Shutter Speed
1/500
Setting No.
Shutter Speed
1/3000
0
5
6
7
8
9
1
2
3
4
1/750
1/4000
1/1000
1/1500
1/2000
1/8000
not used
not used
2.2.2 External Synchronization Terminal Resistance Switch SW4
Switch SW4 sets the resistance of the external synchronization terminal.
Table 2–2 lists the settings.
2-3
Nomenclature and Use of Each Component
Rear Panel Switches and Terminals
Table 2–2.External Synchronization Terminal Resistance Switch SW4
Switch Position
Left
Terminal Resistance Value
75 Ω
Center
100 kΩ
150 Ω
Right
Figure 2–2. External Synchronization Terminal Resistance Switch SW4
Left
Right
Center
Note:
When outputting internal sync signal, set the switch to 100 kΩ.
2.2.3 Mode Switches SW3
The SW3 mode switches control the functions listed in Table 2–2 and
Table 2–4.
Table 2–3.Mode Switches SW3
Switch No.
Mode
Operation
1
2
3
4
5
6
Shutter 1
Refer to list below
Refer to list below
ON for external sync
ON for external sync
ON for interlace
Shutter 2
External sync
External sync
Interlace/noninterlace
Not used
Table 2–4.Shutter list
Shutter 1
OFF
Shutter 2
OFF
Mode
Shutter OFF (1/60 sec. exposure)
Continuous shutter, see Note 1
Continuous shutter, see Note 2
V.I. (Variable Integration)
ON
OFF
ON
ON
OFF
ON
Notes: 1) V reset not done when external trigger is input.
2) V reset done when external trigger is input.
2.2.4 Gain Mode Switch SW2
Gain mode switch SW2 controls the gain as shown in Table 2–5 and
Figure 2–3.
2-4
Nomenclature and Use of Each Component
Gain Variable Volume Control VR1
Table 2–5.Gain Mode Switch SW2
Figure 2–3. Gain Mode Switch SW2
Switch No.
Left
Gain Mode
AGC
Center
Right
Fixed
Variable
Left
Right
Center
2.2.5 Gain Variable Volume Control VR1
WhenvariablegainisselectedwithgainmodeswitchSW2intherightposition,
gain is increased by turning VR1 counterclockwise as shown in Figure 2–4.
Figure 2–4. Gain Variable Volume Control VR1
UP
2.2.6 DC IN Terminal
Use when the power source is supplied by the AC adaptor: PS-780-12J. When
a different type of power source is used, the connector standard must conform
to EIAJ, RC-5320A Voltage Classification 4.
2.2.7 LENS Terminal
When the auto-iris lens plug is connected, the lens iris can be adjusted auto-
matically. This is also the terminal for inputting the shutter trigger cable con-
nector: HR10A-7P–6P. Table 2–6 lists the terminal pins, signals, and levels.
Table 2–6.LENS Terminal
Pin No.
Input Signal
Signal Level
1
2
Field index output
Good for HC125
Shutter trigger input
VI command input
CMOS level
3
4
5
6
Ground
Readout field indicator output
Image signal output (for iris)
DC + 12V output (for lens)
Good for HC125
2-5
Nomenclature and Use of Each Component
DC IN/SYNC Terminal
The odd fields are low and the even fields are high for the pin 1 field index
output.
The pin 5 image signal is provided for auto-iris use so it cannot be con-
nected to a monitor.
The dc voltage output from pin 6 is the same as the input voltage.
2.2.8 DC IN/SYNC Terminal
This terminal supplies the +12 V power, outputs the image from the camera
module, and inputs/outputs sync signals, through cable connector
HR10A–10P–12S. Table 2–7 lists the terminal pins, signals, and levels.
Table 2–7.DC IN/SYNC Terminal
Pin No.
Input/Output Signal
GND
Signal Level
1
2
3
4
5
6
DC + 12V
Image output (GND)
Image output (signal)
HD input/output
HD input (signal)
HD output (signal)
VD input (signal)
VD output (signal)
Optional output (GND)
Optional output (signal)
GND
For HCT14
For HC125
For HCT14
For HC125
7
8
9
For HC126
10
11
12
DC + 12V
VD input/output (GND)
The optional outputs on pins 8 and 9 select shutter monitor output or pixel
clock output.
2-6
Nomenclature and Use of Each Component
Internal Switches
2.3 Internal Switches
Remove the camera cover to set the internal switches. Viewing the camera
from the front, the switches are located on boards in the center and the left.
The center board is called the clock board, and the left board is called the pro-
cess board. Figure 2–5 shows the switch locations.
Figure 2–5. Internal Switches
Clock board inside
(HD/VD
SW1)
Clock board outside
(S1)
Processor board outside
Lens
(ϒ SW1)
Connectors
Bottom
(SW2)
(SW4)
2.3.1 SYNC Signal (HD/VD) Input/Output Switch SW1
Switch SW1 selects between internal sync output and external sync input.
Table 2–8 lists the switch positions and functions, and Figure 2–6 shows the
switch.
Table 2–8.SYNC Signal (HD/VD) Input/Output Switch SW1
Switch Position
Input/Output Mode
Upper
Center
Lower
External sync signal input
Not used
Internal sync signal output
Figure 2–6. SYNC Signal (HD/VD) Input/Output Switch SW1
Upper
Center
Lower
2.3.2 Option Output Switch S1
Switch S1 switches the option output as listed in Table 2–9 and shown in
Figure 2–7.
2-7
Nomenclature and Use of Each Component
Internal Switches
Table 2–9.Option Output Switch S1
Switch Position
Upper
Output Signal
Shutter monitor output
Pixel clock output
Lower
Figure 2–7. Option Output Switch S1
Upper
Lower
2.3.3 Gamma Switch SW1
Gamma switch SW1 changes the gamma characteristics as listed in
Table 2–10 and shown in Figure 2–8.
Table 2–10.Gamma Switch SW1
Switch Position
Gamma Characteristics
γ [gamma] = 1 (OFF)
Not used
Upper
Center
Lower
γ [gamma] = 0.45 (ON)
Figure 2–8. Gamma Switch SW1
Upper
Center
Lower
2.3.4 AC/DC Output Switch SW4
SwitchSW4 switches the output between ac and dc as listed in Table 2–11 and
shown in Figure 2–9.
Table 2–11.AC/DC Output Switch SW4
Switch Position
Output Conversion
DC output
Upper0
Center
Lower
Not used
AC combined output
Figure 2–9. AC/DC Output Switch SW4
Upper
Center
Lower
2-8
Nomenclature and Use of Each Component
Internal Switches
2.3.5 Outline Emphasis Circuit ON/OFF Switch SW2
Switch SW2 controls the outline emphasis circuit on the MC-780PIH. Do not
move this switch on the MC-780PIA. The outline emphasis circuit makes the
image easier to see by emphasizing the image outline when the camera is
used for surveillance. Table 2–12 lists the switch positions and functions, and
Figure 2–10 shows the switch.
Table 2–12.Outline Emphasis Circuit ON/OFF Switch SW2
Switch Position
Operation
Upper
Center
Lower
Outline emphasis ON
Not used
Outline emphasis OFF
Figure 2–10. Outline Emphasis Circuit ON/OFF Switch SW2
Upper
Center
Lower
Note: This function is only for MC-780PIH.
2-9
Nomenclature and Use of Each Component
2-10
Nomenclature and Use of Each Component
Chapter 3
Using the External SYNC Mode
The camera can be synchronized externally by inputting an external sync sig-
nal. When using external sync, set the clock board’s sync signal input/output
switch (SW1) to the external sync signal in (upper switch position) and
switches 3 and 4 to the mode switch (SW3), located on the rear panel, to ON.
Topic
Page
3.1 External Sync With Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
3.2 External Sync With No Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
3-1
External Sync With Interlace
3.1 External Sync With Interlace
On the rear panel, set switch 5 of mode switch SW3 to ON.
3.1.1 External Sync Signal Input Conditions
HD signals: 15.734 kHz ± 1% (63.5 µs ± 1%)
VD signals: 262.5 H
Phase
In Figure 3–1, when the last VD transition is between 47.42 µs ahead and
16.13 µs behind relative to the last HD transition, it becomes the ODD field.
When the last VD transition is between 16.13 µs ahead and 47.42 µs behind
relative to a 1/2 H point from the last HD transition, it becomes the EVEN field.
Figure 3–1. External Sync Timing
1 H
1/2 H
HD
VD
odd field
VD
even field
3-2
Using the External SYNC Mode
External Sync With No Interlace
3.2 External Sync With No Interlace
On the rear panel, set switch 5 of mode switch SW3 to OFF.
3.2.1 External Sync Signal Input Conditions
HD signals: 15.734 kHz ± 1% (63.5 µs ± 1%)
VD signals: 244 ~ 1021 H, (see Notes 1, and 2)
Phase
Figure 3–2. External Sync With No Interlace
2 4 4 ~ 1 0 2 1 H
HD
6 H
VD
Notes: 1) The sync becomes internal sync if the VD does not come above 1022H.
2) VD does not receive 0~243H
3-3
Using the External SYNC Mode
3-4
Using the External SYNC Mode
Chapter 4
Using the Shutter Modes
This chapter describes the various shutter modes and how to use them.
Topic
Page
4.1 Continuous Shutter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
4.2 Random Shutter (Fixed V Sync) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
4.3 Random Shutter (V Sync Reset) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
4.4 VI Mode Shutter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
4.5 Precautionary Items . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
4-1
Continuous Shutter
4.1 Continuous Shutter
On the rear panel mode switch SW3, set switch 1 to ON and switch 2 to OFF.
Use the shutter speed control switch SW1 to set the shutter speed. Figure 4–1
shows the continuous shutter speed control timing.
Figure 4–1. Continuous Shutter Speed-Control Timing
Read out
1 Field
Field indicator (high)
249 µs (PIA)
142 µs (PIH)
Shutter monitor out
4-2
Using the Shutter Modes
Random Shutter (Fixed V Sync)
4.2 Random Shutter (Fixed V Sync)
On the rear panel mode switch SW3, set switch 1 to ON and switch 2 to OFF.
Use the shutter speed control switch SW1 to set the shutter speed.
The random shutter operates only when the shutter command has been
added, so continuous shutter is the normal operating mode.
Figure 4–2 shows the random shutter speed control timing with fixed V sync.
Figure 4–2. Random Shutter Control Timing (Fixed V Sync)
Shutter command
Read out
Output interruption
1 Field
Field indicator output
Shutter monitor output
249 µs (PIA)
142 µs (PIH)
4-3
Using the Shutter Modes
Random Shutter (V Sync Reset)
4.3 Random Shutter (V Sync Reset)
On the rear panel mode switch SW3, set switch 1 to OFF and switch 2 to ON.
Use the shutter speed control switch SW1 to set the shutter speed. Figure 4–3
shows the random shutter speed control timing with V sync reset.
The random shutter operates only when the shutter command has been
added, so continuous shutter is the normal operating mode.
Figure 4–3. Random Shutter Control Timing (V Sync Reset)
Shutter command
Output interruption
Read out
1 Field
V sync reset
Field indicator output
Shutter monitor output
249 µs (PIA)
142 µs (PIH)
4-4
Using the Shutter Modes
VI Mode Shutter
4.4 VI Mode Shutter
On the rear panel mode switch SW3, set switches 1 and 2 to ON. At this point
there will be no image output. When an external VI command is input, expo-
sure will occur for the period of the command. This mode is only for non-inter-
lace. Theimagequalitymaybelowerduetotimedexposures;useaccordingly.
Figure 4–4 shows the VI mode shutter timing.
Figure 4–4. VI Mode Shutter Timing
VI command
Read out
1 Field
Field indicator output
Shutter monitor output
249 µs (PIA)
142 µs (PIH)
Integration time
4-5
Using the Shutter Modes
Precautionary Items
4.5 Precautionary Items
Observe the following precautions when operating the electronic shutter.
The CCD for this camera uses the frame transfer method. At shutter
speeds of 1/500, 1/1000, and 1/1500 second, the exposure period and the
transfer period conflict with the readout period. There is black output from
the line count, which conforms to the shutter speed; the image output fol-
lows. Thus the lower part of the image output cannot be output onto the
screen to the degree of the line count of the black output. Figure 4–5
shows what occurs. Table 4–1 lists the line counts for each shutter speed.
Figure 4–5. Exposure and Transfer Period Conflict With Readout Period
The line count conforming to
the shutter speed outputs black
Screen
The lower part of the image
cannot output to the extent of
the line count conforming to the
shutter speed.
Table 4–1.Line Table Corresponding to Shutter Speeds
Shutter Speed
1/500
MC-7890PIA
MC-780PIH
22
13
6
19
11
3
1/750
1/1000
1/1500
2
–
Duetothecircumstancesnotedabove, duringrandomshutter, whenthere
is no shutter trigger input, the camera will be in continuous shutter mode.
Consequentlythe bottom part of the image is not shown for shutter speeds
of 1/500 through 1/1500 second. Images shot with random shutter have
a full image output without the bottom part eliminated. Thus the image ap-
pears to flicker because the positions shown on the monitor differ.
Whenatimedexposureismadeofover1/60secondoperatinginVImode,
impurities on the CCD may become exaggerated. Also, due to the occur-
rence of dark current, the image may be rough. The image quality of timed
exposures is uncertain.
Use non-interlace scanning when in random shutter and VI modes.
4-6
Using the Shutter Modes
Chapter 5
Initial Settings
This chapter describes the modes of operation and the initial switch settings.
Topic
Page
5-1 Modes and Initial Switch Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
5-1
Modes and Initial Switch Settings
5.1 Modes and Initial Switch Settings
With this unit it is possible to switch the operating modes to suit the intended
use. All mode settings can be set with switches. Table 5–1 summarizes the
modes and initial switch settings.
Table 5–1.Modes and Initial Switch Settings
Function
Initial Setting
—
Setting Switch
Rear panel SW1
Rear panel SW2
Shutter speed switch
Gain (sensitivity)
Fixed gain
Fixed gain
Variable gain
AGC
Electronic shutter
OFF
OFF
Rear panel SW3 – 1, 2
1/60 seconds
continuous shutter
Random shutter (V fixed)
Random shutter (V reset)
VI shutter (optional exposure period)
Internal/External Sync
Internal sync
Interlace
75Ω
Rear panel SW3 – #, 4
Rear panel SW3 – 5
Rear panel SW4
Interlace/Non-Interlace
Sync signal input/output impedance
75Ω/150Ω/100kΩ
Gain variable volume
—
Rear panel VR1
Clock board SW1
Clock board S1
Sync signal input/output
Optional input/output shutter
Shutter monitor output
Input
monitor out
Pixel clock output
γ switch characteristics
γ = 1/0.45
γ = 1
Process board SW1
Process board SW4
Process board SW2
Output signal coupling
AC combined out/DC output
Outline emphasis circuit (PIH only)
AC combined output
OFF
5-2
Initial Settings
Chapter 6
Precautions for Use
Topic
Page
6-1 Precautions for Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2
6-2 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3
6-1
Precautions for Use
6.1 Precautions for Use
6.1.1 Power Source
The camera operates on +12 V. Use a stable ripple- and noise-free power
source.
6.1.2 Heat Reduction
To keep the temperature inside the camera from rising in some situations
(such as when operating the camera inside a tightly sealed case) it may be
necessary to use forced air conditioning.
6.1.3 Locations for Use and Storage
Do not operate or store the camera in the following locations:
Locations of extreme heat or cold. The proper temperature for use is 0°C
to 40°C.
Locations with considerable moisture or dust
Locations in direct contact with rain (the camera is not waterproof or mois-
ture-proof)
Locations with corrosive gas
Locations with flammable gas (it is not explosion-proof)
Locations with severe vibration
Near radios or television transmitters, which generate strong electrical
waves
6-2
Precautions for Use
Maintenance
6.2 Maintenance
Use a blower to remove dirt or dust adhering to the CCD glass cover. Wiping
the glass forcefully can damage the glass or create static electricity that can
damage the CCD.
Use a soft, dry cloth to clean dirt off the exterior. If it is extremely dirty, use a
small amount of a neutral detergent on a cloth to remove it, and then wipe with
a dry cloth. Do not use alcohol or benzene, as they may discolor the surface
and cause peeling.
6-3
Precautions for Use
6-4
Precautions for Use
Chapter 7
Specifications
This chapter lists the specifications for the cameras.
Topic
Page
7-1 Image System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2
7-2 Optical Elements and Other Specifications . . . . . . . . . . . . . . . . . . . . . . 7-3
7-1
Image System
7.1 Image System
Table 7–1 lists the image system specifications for the MC–780PIA; Table 7–2
lists specifications for the MC–780PIH.
Table 7–1.MC–780PIA Image System Specifications
Item
Specification
Imager
Frame Transfer Method CCD (TI manufactured CCD TC241-30)
754 × 484 (horizontal/vertical)
Effective Pixel Count
Sensor Screen Area
Signal System
2/3 inch format (screen size 8.8 mm × 6.6 mm)
Based on EIA–170A system
Table 7–2.MC–780PIH Image System Specifications
Item
Specification
Imager
Frame Transfer Method CCD (TI manufactured CCD TC245-30)
754 × 484 (horizontal/vertical)
Effective Pixel Count
Sensor Screen Area
Signal System
1/2 inch format (screen size 6.4 mm × 4.8 mm)
Based on EIA–170A system
7-2
Specifications
Optical Elements and Other Specifications
7.2 Optical Elements and Other Specifications
Table 7–3 lists other specifications common to the two cameras.
Table 7–3.Optical Elements and Other Specifications
Item
Specification
Lens Mount
C-mount
Flange back
17.526 mm (can be fine adjusted)
Internal/External
Synchronization System
Sync Input/Output
Jitter
HD/VD (signal level:TTL level)
Within ±60 nsec
Scanning Method
Image Output
2:1 interlace/non-interlace
1.0 V p-p, Sync negative, 75 Ω unbalanced
More than 565 lines
Horizontal Resolution
Illumination
0.8 Lux (fixed gain, see Note 1)
0.1 Lux (maximum gain, see Note 1)
Minimum Illumination
S/N Ratio
MC–780PIA: over 53 dB
MC–780PIH: over 55 dB
Gain
Auto gain adjust/fixed gain/variable gain
gamma = 1/0.45
gamma Characteristics
White Clip
120IRE±15IRE
Shutter Modes
Continuous shutter/random shutter/VI-mode shutter
1/500, 1/750, 1/1000, 1/1500, 1/2000, 1/3000. 1/4000, 1/8000
12 V (range 10.5 V to 15 V)
Shutter Speeds
Power Source
Power Consumption
Operating Temperature
Operating Humidity
Maintenance Temperature
Maintenance Humidity
Oscillation
Approximately 4.2 W
0–40°C
20–80% (There must be no dew formation.)
–20°C to +60°C
20–95% (There must be no dew formation.)
4.4 G (11–100 Hz)
Exterior Dimensions
Weight
44(W) 48(H) 112(D) mm (includes protruding section)
215 g
Accessories
Focus Ring Cap (1)
User’s Manual (1)
AC Adaptor
Japan Local Model (PS-78012J)
1) Illumination measured with Davitson Optronics Optoliner.
2) These specifications may change without notice due to improvements.
7-3
Specifications
7-4
Specifications
Chapter 8
Exterior Dimensions
This chapter lists exterior dimensions.
Topic
Page
8-1 Exterior Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2
8-1
Exterior Dimensions
8.1 Exterior Dimensions
Figure 8–1 shows the exterior dimensions for the camera. The following notes
apply:
1) unit:mm
2) Since the focus ring is adjustable, this is the middle value (1.2 mm).
3) The TI logo for the camera cover is a sticker with one adhesive side.
4) The shape and designation may change due to improvements.
8-2
Exterior Dimensions
Exterior Dimensions
Figure 8–1. Exterior Dimensions
8-3
Exterior Dimensions
8-4
Exterior Dimensions
Chapter 9
Other Issues
This chapter discusses cable and connector issues.
Topic
Page
9-1 Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-2
9-1
Connectors
9.1 Connectors
We do not sell cable connectors. They can be obtained from appropriate de-
partments of Hirose Electrical Co.
Main Business Office
Gotanda I-S Building, 10th Floor
1-11 Osaki 5-chome, Shinagawa-ku, Tokyo 141
Telephone: (03)3492-2162
Fax: (03)3490-9229
Osaka Business Office
2-22 Tai deramachi, Kita-ku, Osaka 530, Osaka
Telephone: (06)312-4661
Fax: (06)312-4335
Cable Part Numbers
6-pin: HR10A-7P-6P
12-pin: HR10A-10P-12S
9-2
Other Issues
IMPORTANT NOTICE
Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue
any product or service without notice, and advise customers to obtain the latest version of relevant information
to verify, before placing orders, that information being relied on is current and complete. All products are sold
subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those
pertaining to warranty, patent infringement, and limitation of liability.
TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent
TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily
performed, except those mandated by government requirements.
CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF
DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL
APPLICATIONS”). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR
WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER
CRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO
BE FULLY AT THE CUSTOMER’S RISK.
In order to minimize risks associated with the customer’s applications, adequate design and operating
safeguards must be provided by the customer to minimize inherent or procedural hazards.
TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent
that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other
intellectual property right of TI covering or relating to any combination, machine, or process in which such
semiconductor products or services might be or are used. TI’s publication of information regarding any third
party’s products or services does not constitute TI’s approval, warranty or endorsement thereof.
Copyright 1998, Texas Instruments Incorporated
|