DAB-129ID
Owner’s
Handbook
Clock radio with dock for iPod
IMPORTANT SAFETY INFORMATION
Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as the power-supply cord
or plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally,
or has been dropped.
Warning: To reduce the risk of fire or electrical shock,
do not expose this product to rain or moisture. The
product must not be exposed to dripping and splashing
and no object filled with liquids such as a vase of
flowers should be placed on the product.
IMPORTANT
CAUTION!
RISK OF ELECTRIC SHOCK
DO NOT OPEN
This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communication. However, this
is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the
interference by one of the following measures:
TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK)
This symbol indicates that there are impor-
tant operating and maintenance instructions
in the literature accompanying this unit.
This symbol indicates that dangerous voltage
constituting a risk of electric shock is present
within this unit.
-
-
Reorient or relocate the receiving antenna.
Increase the separation between the equipment
and receiver.
No naked flame sources such as candles should be
placed on the product.
Caution: Changes or modifications not expressly
approved by the manufacturer could void the user’s
authority to operate this device.
Caution: Usage of controls or adjustments or
performance of procedures other than those specified
herein may result in hazardous exposure.
-
-
Connect the equipment into an outlet on
circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV
technician for help.
a
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with a slightly damp cloth.
Do not block any ventilation openings.
Install in accordance with the manufacturer’s
instructions.
ELECTRICAL INFORMATION
Use this appliance only with the supplied AC Adaptor.
Using non-approved power supplies will void the
warranty.
Mains Supply: The mains operating voltage of the
AC Adaptor is marked on a rating plate on the AC
Adaptor.
Do not install or operate near any heat sources such
as radiators, stoves, or other apparatus that produce
heat.
The means of disconnecting this appliance from
the mains supply is the AC adaptor. This should be
unobstructed and readily operable at all times.
Unplug this apparatus during lightning storms or when
unused for long periods of time.
1
INTRODUCTION
PRELIMINARIES
INDEX
INDEX
The DAB-129ID is a full-function remote controlled DAB and
FM clock/radio with dual alarms and dock for an iPod.
The clock/radio function features a large-format backlit
display for easy night reading.
UNPACKING
Carefully unpack the unit. If it is damaged, please return it to
your nearest Tesco store for replacement. Remember to take
your purchase receipt with you.
Retain the User Handbook. If you pass the unit on to a third
party make sure you pass on the handbook.
Important safety information..................................1
Introduction ............................................................2
Unpacking ...............................................................2
Controls & Connections............................................3
Display features .......................................................4
Remote control........................................................5
Getting started ........................................................5
Power control ..........................................................6
DAB reception..........................................................6
Volume control ........................................................6
DAB scanning ..........................................................7
DAB display modes ..................................................7
Selecting a source....................................................8
FM reception............................................................8
Radio presets...........................................................8
Docking connecting and playing an iPod.................9
Playing Aux sources ...............................................10
Setting the alarms.................................................11
Checking and waking to the alarms.......................12
DAB Settings menu................................................13
FM settings menu and display modes....................15
Sleep function .......................................................15
Care & Maintenance...............................................15
Troubleshooting ....................................................15
Specifications ........................................................15
We suggest you retain the packaging. If you dispose of it, do
so having regard to any recycling regulations in your area.
CONTENTS
The carton should contain:
•
•
•
•
The DAB-129ID Clock/radio
AC adaptor
Remote control with battery
Operating Manual
If any items are missing or damaged, contact your nearest
TESCO store for a replacement. Have your receipt ready when
you call. Retain the packaging. If you dispose of it, do so
having regard to any recycling regulations in your area.
LOCATION
Place the unit on dry stable surface away from heat and
damp and where it is unlikely to fall or be knocked over.
Warranty ...............................................................15
2
CONTROLS & CONNECTIONS
FRONT VIEW
BACK VIEW
a
b
c
iPod docking bay
Menu/Standby button
Function button
a
b
c
d
DC input jack
Aux in jack
Headphone jack
DAB/FM Aerial wire
d /,/Scan button
e
f
g
Snooze/Dimmer button
Volume/Select Control
Display
3
DISPLAY FEATURES
DISPLAY LAYOUT
TIME DISPLAY
The display shows the
current time and date when
set to Standby.
VOLUME DISPLAY
When changing the volume
level, the display shows a
volume bargraph.
a
Alarm 1 set symbol
Alarm 2 set symbol
Sleep symbol
Time display
Station name/Source display
Info display
b
c
d
e
f
SNOOZE DISPLAY
When Snooze has been set
after the alarm has sounded,
the remaining snooze time
counts down at the bottom
of the display.
4
GETTING STARTED
REMOTE CONTROL BATTERIES
REMOTE CONTROL
BEFORE FIRST USE
DAB/FM AERIAL
Before using the remote control, the battery (supplied) must
be fitted.
Before using your radio for DAB or FM reception, unwrap
and fully extend the aerial wire. You may need to adjust the
position of the aerial wire for maximum signal strength.
CONNECTING POWER
Before connecting the power, check that the mains voltage
on the rating plate of the AC adaptor is the same as the
voltage in your area.
FITTING/REPLACING THE BATTERY
When fitting or replacing the battery in the remote control,
refer to the diagram below.
1. Press the catch across.
2. While holding the catch, open the battery door.
•
Plug the DC cord from the AC adaptor into the DC jack on
the back of the unit.
•
Plug the AC adaptor into the wall socket and switch the
mains power on.
The unit is now ready for use.
NOTE:- The AC adaptor may become warm during operation
- this is normal.
3. Fit the battery observing polarity as shown. When
replacing the battery, use only the same CR2025 type
specified.
a
b
c
d
e
Standby button
Mute button
Function button
Up button
When first connected to the power, the clock and calendar
display will show ‘zeros’.
Select/Enter button
f { /Info button
Down button
h /, /Scan button
Sleep button
g
BATTERY DISPOSAL
i
1) Snooze/Dimmer button
1! Alarm 2 button
1@ } /Preset button
1# Alarm 1 button
Dispose of used batteries with regard to the recycling
regulations in your area. Do NOT short circuit batteries or
throw them into water, the general rubbish or in a fire.
Weak batteries can leak and damage the remote control.
Replace them in good time!
SETTING THE CLOCK
The clock on your radio is automatically set when first used
from the time signal broadcast with DAB radio stations.
If a DAB station is not available, the clock may be set manually
via the MENU system (see page 13).
1$ Menu button
1% Numeric keypad
1^ Volume down button
1& Volume up button
5
POWER CONTROL
BROWSING FOR A STATION
ADJUSTING THE VOLUME
To adjust the volume from the front panel controls:
STANDBY CONTROL
To turn the radio on:
To browse for another DAB station from the front
panel controls:
•
Turn the VOLUME/SELECT button to adjust the volume,
clockwise to increase and anti-clockwise to decrease.
•
Press the MENU/ button on the front panel or the red
•
Press the MENU button.
To adjust the volume from the remote control:
button on the remote control.
<Station list> will be displayed.
•
Press the or button to increase or decrease the
volume level.
The display will light and the radio will switch on.
To turn the radio off:
•
•
•
Push the VOLUME/SELECT control to display the station
list.
Turn the VOLUME/SELECT control to browse the station
list.
Push the VOLUME/SELECT control to select the station
displayed.
When the volume is adjusted the display will change to show
the current volume setting on a bargraph.
•
Press and hold the MENU/ button on the front panel or
press the button on the remote control briefly.
The radio will switch off. The clock will continue to run whilst
mains power is connected.
After a short delay, the radio will tune to the station.
To browse for another DAB station from the remote
control:
INITIAL SCAN
When your radio is switched on for the first time the
scanning display will be shown while the scanning process
takes place:
•
Press the Mor Nbutton repeatedly to browse through
the station list.
Volume bargraph
•
When you find a station you want to play, press the
SELECT/ENTER button.
MUTE
After a short delay, the radio will tune to the station.
To mute the sound:
•
Press the MUTE button.
The sound will mute and ‘Volume Muted’ will be displayed..
Progress bar
Number of stations found
•
Press the MUTE button again to restore the sound to its
The radio scans all usable stations (full scan) and stores them
alphanumerically - 1 Radio, 2 Radio, AA Radio, AB Radio...
The initial scan will take a few minutes. After the scan, the
clock will be set and the radio will display the name of the
first station in the sequence. To select this station, push the
VOLUME/SELECT/ENTER control on the front panel (or the
SELECT/ENTER button on the remote control). To browse for
another station, refer to the next section.
previous volume level..
6
DAB SCANNING
DAB DISPLAY MODES
RE-SCANNING FOR DAB STATIONS
DISPLAY MODE OPTIONS
DLS (Dynamic Label Segment): This is a scrolling message
giving real-time information - song titles, news headlines,
etc.
SIGNAL STRENGTH: This setting will display a signal
strength bargraph. The longer the bargraph, the stronger the
signal. Setting the display to show signal strength is useful
when setting up the aerial for the strongest signal.
PROGRAMME TYPE: This describes the style of the
programme being broadcast.
MULTIPLEX NAME: DAB Digital radio stations are broadcast
in multiplexes. Each multiplex is a bundle of radio stations
transmitted in a single frequency. There are national and
local multiplexes; local ones contain stations specific to your
area. This option displays the name of the multiplex name
that contains the station you are listening to.
MULTIPLEX NUMBER/FREQ: This option will display the
multiplex number and frequency that contains the station
you are listening to.
SIGNAL ERROR RATE: This option will display the level of
signal errors in the current broadcast. The lower the number,
the better the quality of the signal.
BIT RATE: DAB allows broadcasters to vary the BIT RATE (or
the amount by which an audio signal can be compressed)
depending on the type of broadcast. This enables the amount
of stations on a multiplex to be maximised. Speech and News
are often broadcast at a lower Bit Rate; music needs a higher
Bit Rate for good fidelity.
When first used, your radio scanned the DAB band for
available stations. The station services found were then
stored in your system’s memory.
You can re-scan the band at any time if you move to a different
area or just to refresh the stored list of available stations.
To scan for DAB stations manually:
The bottom line of the display can be switched to show
different items of information that may be transmitted with
a DAB station.
Choosing the information display:
Press the {/INFO button on the remote control repeatedly
to change the information displayed while playing a DAB
radio station.
The full range of display options are shown below. Some
stations may not broadcast all of these options.
•
•
Select the DAB band.
Press the /,/SCAN button on the front panel or remote
control.
The scanning process will take a few minutes. The number of
services found during the scan will be shown at the right side
of the display.
After the scan, the radio will re-tune to the last station
playing if it is available. If this station is not available, the
name of the first station in the sequence will be displayed.
To select this station, push the VOLUME/SELECT control or
press the SELECT/ENTER button on the remote control.
Alternatively, you can continue to browse for another station
as described on the previous page.
DISPLAY DIMMER
The display brightness can be switched between high and
low settings by pressing the SNOOZE/DIMMER button on
the front panel or remote control.
TIME AND DATE:Time and date are updated by broadcasted
information.
7
SELECTING A SOURCE
LISTENING TO FM RADIO
STATION PRESETS
SOUND SOURCES
You can choose to listen to the following sources -
Your radio can also receive FM band radio stations and display
RDS data (where broadcast).
To change to the FM band
DAB and FM presets
Using the remote control, your radio can store up to 10 of your
favourite stations as presets on both the DAB and FM bands
for quick recall. Direct access number buttons are available
for Presets 1 to 6. For this reason you may prefer to store your
most-used stations in Presets 1 to 6.
•
•
•
•
DAB radio
FM radio
•
Press the FUNCTION button repeatedly to select FM
iPod (when docked)
Aux source (when connected via the rear panel AUX
jack).
mode.
To auto-tune to FM stations
•
Press the SCAN button to search for the next station in
To quick store preset 1 to 6
Selecting a source:
the band.
•
•
Tune to the station you want to store as a preset.
Press and hold one of the NUMBER buttons.
•
Press the FUNCTION button on the front panel or
remote control repeatedly to scroll through the available
sources.
The radio will search and the tuning frequency will be displayed
whilst searching.
When a usable station is detected the radio will stop tuning and
play the station. If RDS data is present, the station name and
scrolling radio text will be displayed. If RDS data is not present,
the tuned frequency will be displayed.
To recall a preset 1 to 6
Press one of the NUMBER buttons briefly.
•
The preset station will be tuned. If the preset selected is empty,
then the radio will continue to play the last selected station.
To store any preset 1-10
To manually tune to FM stations
•
•
Tune to the station you want to store as a preset.
Press and hold the }/PRESET button.
•
Press the M or N button on the remote control to tune
the band in 50kHz steps.
‘Preset Stored’ will be displayed.
•
Press the M or N button repeatedly to find the preset
STEREO/MONO RECEPTION
number you want to store.
For each preset number the preset station currently stored will
be displayed or ‘Empty’ if none is stored.
You can set your radio to switch automatically between
stereo and mono FM reception (Mono/Stereo mode) or to
receive in mono only (Mono Only mode). Setting to Mono
Only mode may improve sound quality in areas where a weak
aerial signal results in a high level of background noise. FM
audio mode selection is made via Audio Setting in the FM
menu. Refer to the FM Settings Menu section on page 15 for
more details of the FM menu.
•
Press the SELECT/ENTER button to confirm if you want
to store the station in the displayed preset number.
To recall any preset 1-10
•
•
Press the }/PRESET button briefly.
Press the M/UP or N/DOWN repeatedly to find the
preset number you want to play.
•
Press the SELECT button briefly to play the preset.
8
iPod ADAPTORS
FINDING AN ADAPTOR
CONNECTING OTHER iPod
MODELS (INC SHUFFLE)
Before docking your iPod you must first check if your iPod
has a docking connector. Early iPod models do not have one
and cannot be docked to your unit. The docking connector is
located on the base of the iPod as shown below.
If you don’t have a dock adaptor
If your iPod was not supplied with a standard dock adaptor,
or if you have lost the adaptor, you can buy one from Apple
on-line. To determine the exact model of your iPod, refer to
can then browse the iPod accessories page on the Apple
website to find an adaptor for your iPod model that can be
purchased on-line.
If you own an iPod Shuffle, a model without dock connector
or prefer to connect your iPod by cable, you can connect the
sound output to the AUX IN jack on the rear panel.
Headphone socket
To the AUX IN jack
Docking Connector
Before docking your iPod, you must first fit the correct iPod
adaptor to the docking bay. Each iPod adaptor matches the
shape of a particular iPod and is necessary to ensure that
your iPod is securely held when docked.
iPod adaptor
Docking bay
•
•
Using a 3.5mm stereo jack to jack cable (supplied),
connect one end of the cable to the headphone socket
of the iPod, and the other end to the AUX IN jack on the
back panel.
To listen to your iPod, follow the instructions on page 10
for playing equipment connected to the AUX IN jack.
FITTING THE iPod ADAPTOR
When your iPod was new it may have been supplied with a
standard dock adaptor in the packaging. If so, fit the adaptor
by pressing it gently into the Docking Bay as shown above.
NOTE: Do not dock an iPod without fitting the correct adaptor,
you may damage the iPod and your unit.
NOTE:- The volume control of the iPod must be turned up
when playing through the AUX IN jack.
NOTE:- An iPod connected to the AUX IN jack cannot be
operated from the remote control and will not be activated
by the alarm.
9
DOCKING AN iPod
PLAYING FROM AN iPod
AUX SOURCES
DOCKING YOUR iPod
To dock your iPod:
Once an iPod is docked, you can operate your iPod functions
from the remote control.
Playback functions:
The AUX IN input may be used to connect sound sources with
a Line or Headphone analogue output to play through your
unit. These may include -
•
•
Switch off the power.
Check that the correct iPod adaptor is fitted to the docking
bay.
•
Press the /,/SCAN button to toggle between Play and
Pause mode at any time.
•
•
•
•
•
iPod models that cannot be docked to the unit
MP3 players
CD walkman players
Tape walkman players
Personal computers or laptops
•
Press the }/PRESET or {/INFO button to select the
next or previous track on your iPod.
•
•
Locate the iPod on the Docking Connector and press it
gently home.
The unit will switch on and the iPod will start to play.
iPod menu functions:
To remove your iPod from the dock:
When an iPod is docked and playing you can navigate the
menus from the front panel or remote control.
Connecting to the AUX IN jack
•
•
Grip the iPod at the sides.
Lift the iPod gently from the dock.
•
Connect a stereo 3.5mm jack cable (supplied) between
the headphone or LINE/AUX output of the personal audio
player and the AUX IN jack on the back panel.
•
To move up through the iPod menu, press the MENU
button.
•
To scroll up and down options displayed on the iPod menu,
turn the VOLUME/SELECT control on the front panel or
press the M or N button on the remote control.
To select menu items, push the VOLUME/SELECT control
or press the SELECT/ENTER button on the remote
control.
CHARGING AN iPod
Playing the AUX source
•
Press the FUNCTION button repeatedly to select AUX
When an iPod is docked, the iPod will begin to charge
automatically.
NOTE:- The iPod will not charge when the radio is set to
Standby.
mode.
•
Auxiliary Input Mode will be displayed.
•
•
Set your personal audio player/computer to PLAY.
Set the listening volume to the level you want with the
volume controls on the radio or remote control.
If there is no sound or if the volume level is not loud enough,
you may need to increase the volume setting on your personal
audio player/computer.
10
SETTING THE ALARMS
SETTING THE ALARMS
To make a change to a setting:
ALARM SETTING SEQUENCE
You can set two completely separate alarm times (ALARM 1
and ALARM 2) and activate either or both of them to wake
you with a buzzer, radio, or music from a docked iPod. You can
also pre-set the station preset and volume settings that the
alarms will wake you with.
1. Press the M or N button to scroll through the options
available for a setting (or times when clock setting).
2. When you have finished changing a setting, press the
SELECT/ENTER button to confirm the setting and move
on to the next setting in the sequence.
The alarms are set from the remote control or from within the
Settings Menu (see page 13).
3. Repeat the previous two steps to change each setting as
required.
*NOTE:- When changing the Alarm radio preset setting,
choose the ‘Last listened’ option to wake to the last station
you played before setting the radio to Standby.
Checking and changing alarm settings:
All alarm settings are made through the Alarm menu.
NOTE:- You must complete all settings before leaving the
menu or your changes won’t be saved.
Saving alarm settings:
Your alarm settings are automatically saved when you
complete the last setting and press SELECT/ENTER.
The display will confirm with the words ‘Alarm saved’.
Setting Alarm 1:
•
Switch on the radio (Alarm settings cannot be changed
when set to Standby).
•
Press the ALARM1 button on the remote control.
Setting Alarm 2:
‘Alarm 1 Setup’ will appear on the display.
•
•
Press the ALARM2 button on the remote control to open
the Alarm menu and set Alarm 2.
Press the SELECT/ENTER button if you want to set Alarm
1.
•
To change the settings, follow the procedure described
for setting Alarm 1 on this page.
‘Alarm 1 Wizard’ will appear on the display.
The alarm is now set in the sequence shown in the next
column.
NOTE: Press the MENU button at any time to exit alarm
setting, leaving the settings unchanged.
11
CHECKING ALARM SETTINGS
WAKING TO THE ALARMS
You can step through the setting procedure without making
any changes to check the alarm settings.
SETTING THE ALARM TO WAKE YOU
To set the alarm to wake you:
WHEN THE ALARM WAKES YOU
When the alarm sounds you can choose to set snooze, which
will reset the alarm for a further 9 minutes, or to switch it
off.
•
Check that the Alarm 1 and/or Alarm 2 symbols are
displayed as required. If not, set the Alarm(s) On as
described in the ‘Setting the Alarms’ section on the
previous page.
To check the settings for Alarm 1 or 2:
•
•
•
Switch the radio on.
Press the ALARM1 (or ALARM 2) button.
Press the SELECT/ENTER button repeatedly to step
through the settings and view them without making any
changes.
To set snooze:
•
To set snooze, press the SNOOZE/DIMMER button when
the alarm sounds.
Alarm 1 set
Alarm 2 set
The alarm will stop and the alarm indicator and the snooze
time will count down on the display. After 9 minutes the alarm
will sound again.
•
Continue to view the steps until ‘Alarm Saved’ is
displayed.
To switch off the alarm:
ALARM REPEAT
•
To switch off the alarm, press the MENU/ button or
the button on the remote control.
The alarm(s) will repeat according to the Alarm Repeat
setting you made when setting the alarm.
The unit will set to Standby.
•
•
Daily - The alarm will sound every day.
Weekdays - The alarm will sound on weekdays, but not
at weekends.
•
•
If you have set either wake up mode to ‘iPod’, make sure
that your iPod is docked.
Set the radio to Standby (or set the SLEEP function).
•
•
Weekends - The alarm will sound on weekends, but not
on weekdays.
Once - The alarm will sound only once. If this setting has
been chosen, an extra option is added for you to set the
date that you want the alarm to sound.
The radio will switch off and the time and date will be displayed
with the Alarm Symbol(s).
12
ADVANCED OPERATION - DAB SETTINGS MENU
13
DAB SETTINGS MENU (contd.)
DAB SETTINGS MENU
MORE DETAIL OF THE DAB SETTINGS MENU OPTIONS:
MAIN MENU/SYSTEM SETUP/FACTORY RESET: This option
will restore all settings to ‘factory original’. All clock and
alarm times, station lists and any stored preset stations will
be cleared. After factory reset the radio will automatically re-
scan the DAB band when first used.
Your radio has some additional features and options that
may be reached through the Settings Menu.
A complete map of the menu is shown on the previous page.
NOTE: The main menu options may be useful for accessing
features such as alarm setting and sleep time if the remote
control is not to hand.
STATION LIST: Selecting Station List will exit the Settings
Menu to browse the DAB station list. Stations may be selected
from the list.
FULL SCAN: Select Full Scan to re-scan the entire DAB band
and refresh the station list. A Local Scan (selected with the
SCAN button) will scan only the bands used in the locality of
the radio. A full scan will scan all bands.
MAIN MENU/SLEEP: Choose this option to set the Sleep
time from within the settings menu. Note that this option
enables Sleep time to be set from the control panel of the
unit if the remote control is not available.
To enter the DAB Settings Menu from the front panel
controls:
MANUAL TUNING: Manual tuning enables you to search the
band manually, stepping through the multiplex numbers
to check if any have usable signal strength. Manual tuning
is not necessary in normal operation where scanning will
have automatically established a station list of all useable
stations.
•
Set to DAB mode.
MAIN MENU/ALARMS: Choose this option to view or
change the settings of Alarm 1 or Alarm 2 from within the
settings menu. Note that this option enables Alarm settings
to be checked or changed from the control panel of the unit if
the remote control is not available.
•
Press the MENU/ button.
To scroll through available options, turn the VOLUME/SELECT
control. To choose an option from the menu, push the VOLUME/
SELECT control.
To enter the DAB Settings Menu from the remote
control:
DRC: DRC is Dynamic Range Compression. Enabling DRC may
improve the sound of DAB radio when listening in a noisy
room.
PRUNE: If your station list includes stations that you can no
longer receive (you may have moved to a different area), you
can select the ‘Prune’ option to remove any stations that can
no longer be received from the Station List.
MAIN MENU/SW VERSION: This option will display the
version number of the control software currently installed
in your radio. This will be helpful to a technician who is
servicing the radio.
•
•
•
•
Set to DAB mode.
Press the MENU button.
Press the M button to scroll through available options.
To choose an option from the menu, press the SELECT/
ENTER button.
MAIN MENU/DAB: This option will exit the settings menu
to play DAB radio.
MAIN MENU/FM: This option will exit the settings menu to
play FM radio.
MAIN MENU/SYSTEM SETUP/TIME SETUP: This menu
option enables the clock to be set manually if there is no
available DAB transmission.
14
FM SETTINGS MENU
FM DISPLAY MODES
SLEEP FUNCTION
FM SETTINGS MENU
FM DISPLAY MODE OPTIONS
SLEEP TIMER
There are also some menu settings that are specific to FM
radio operation. These settings may be changed through the
Settings Menu.
The bottom line of the display can be switched to show
different items of information that may be transmitted with
an FM station.
You can set the Sleep timer to play music for a set period
while you are falling asleep.
To set the sleep timer:
To change the display mode:
•
•
Play your choice of music.
To enter the FM Settings Menu:
Press the {/INFO button on the remote control repeatedly
to change the information displayed while playing an FM
radio station.
The full range of display options are shown below. Some
stations may not broadcast all of these options.
Press the SLEEP button on the remote control repeatedly
to cycle through the sleep time options of 15 minutes,
30 minutes, 45 minutes, 60 minutes, 90 minutes or OFF
(sleep off).
Press the SELECT/ENTER button to confirm the sleep
time.
•
Set to FM mode.
•
Press the MENU/ button on the front panel or the
MENU button on the remote control.
A map of the menu is shown below. To scroll through available
options, turn the VOLUME/SELECT control or press the M
button on the remote control. To choose an option from the
menu, press the SELECT/ENTER button.
•
The Sleep symbol will be displayed amd music will continue
to play for the time you selected, then the unit will set to
Standby.
NOTE:- Sleep time can also be set through the Settings Menu
if the remote control is not available.
HEADPHONES
There is a headphone output jack on the back panel of the
radio. If headphones are connected to this socket for private
listening, the speakers will cut out automatically.
MORE DETAIL OF THE FM SETTINGS MENU OPTIONS
SCAN SETTING: With this menu option you can set the
scanning sensitivity of the FM radio to two different levels-
‘Strong stations only’ or ‘All stations’. Setting to ‘Strong
stations only’ will exclude weaker stations resulting in a
quicker scan. If you set to ‘All stations’ the scan will stop at
every station detected, even if the signal is weak.
AUDIO SETTINGS: This option enables you to set the radio
to receive FM in Auto mode (Mono/Stereo) or in Mono only.
This may be useful if the signal is weak and the broadcast
is noisy.
15
CARE AND MAINTENANCE
TROUBLESHOOTING
WARRANTY&SPECIFICATIONS
CARE AND CLEANING
Poor quality radio reception
SPECIFICATIONS
All care and cleaning operations should be carried out with
the unit unplugged from the mains power.
The surface of the unit can be cleaned with a barely damp
cloth and then dried carefully. Never use abrasives, abrasive
cloths or chemical solvents .
The aerial signal may not be adequate. Try repositioning the
aerial while watching the signal strength. Signal strength
can be displayed by tuning to a DAB station and pressing the
{/INFO button
Supply Voltage, Current :. 9V , 1.5A
AC Adaptor input:............ 100-240V ~, 0.5A max.
Output power.................. 2W rms
Frequency range ............. 174.928-239.200MHz (DAB)
87.5-108MHz (FM)
Alarm not sounding
Net Weight:..................... 2.85kg
Check that you set Alarm 1 or Alarm 2 on in the alarm setting
sequence. When the alarms are on, the Alarm 1 or Alarm 2
symbol will be displayed.
Class II construction double insulated.
This product must not be connected to earth.
Alarm sound not audible or too loud:
Change the alarm volume setting. This setting is changed in
the ‘alarm setting’sequence.
UK: Waste electrical products/batteries should
not be disposed of with household waste.
Separate disposal facilities exist, for your near-
in-store for details.
No sound/low volume from AUX source:
Check that the volume control is turned up on the AUX
source.
Poor quality radio reception when an iPhone is
docked:
You may need to set the iPhone to ‘airplane’ mode when
docked.
ROI: Produced after 13th August 2005. Waste
electrical products/batteries should not be dis-
posed of with household waste. Please recycle
where facilities exist. Check with your Local Au-
thority or retailer for recycling advice.
WARRANTY
Your Tesco appliance is covered by a warranty for 12 months
from the date of purchase. If a fault develops during this
period, please contact the TESCO electrical help line on 0845
456 6767. Please have your original purchase receipt with
you when you call. This warranty in no way affects your
consumer rights.
16
Te sco Stores Ltd,
Delamare Road, Cheshunt, Herts, EN8 9SL
Technika Helpline: 0845 456 6767 (Calls cost up to 4p per minute from a BT landline, other providers may vary)
DAB129ID V0.1
|