INSTRUCTION MANUAL
BS-1030B
BS-1030W
UNIVERSAL SPEAKER
Please follow the instructions in this manual to obtain the optimum results from this unit.
We also recommend that you keep this manual handy for future reference.
The BS-1030 Series Speakers are small in size and feature the wide-band, high-quality, 2-way bass-reflex design which
makes them ideal for such applications as announcements and music reproduction.
1. SAFETY PRECAUTIONS
WARNING Indicates a potentially
• Be sure to read the instructions in this section carefully
before use.
hazardous situation which, if mishandled, could result in
death or serious personal injury.
• Make sure to observe the instructions in this manual as
the conventions of safety symbols and messages
regarded as very important precautions are included.
• We also recommend you keep this instruction manual
handy for future reference.
• Avoid mounting the unit in locations exposed to constant
vibration. The mounting bracket can be damaged by
excessive vibration, potentially causing the speaker to
fall, which could result in personal injury.
WARNING Indicates a potentially
hazardous situation which, if mishandled, could result in
death or serious personal injury.
CAUTION Indicates a potentially hazardous
situation which, if mishandled, could result in moderate
or minor personal injury, and/or property damage.
• Use only the specified amplifier output voltage and
impedance, as exceeding the specified limits could result
in fire or other failures (high-impedance applications).
• To avoid electric shocks, be sure to switch off the
amplifier power when connecting the speaker.
• To avoid accidental air explosions, do not use the unit
around gasoline, thinner or other combustibles.
• Avoid installing the unit in humid or dusty locations, or in
locations exposed to heaters, solvents, acid, alkali,
smoke, or steam, as excessive exposure to these factors
could result in the speaker falling off, electric shock or
fire.
• Install the unit only in a location that can structurally
support the weight of the unit and the mounting bracket.
Doing otherwise may result in the unit falling down and
causing personal injury and/or property damage.
• Do not operate the unit for an extended period of time
with the sound distorting. This is an indication of a
malfunction, which in turn can cause heat to generate
and result in a fire.
• Do not use other methods than specified to mount the
bracket. Extreme force is applied to the unit and the unit
could fall off, possibly resulting in personal injuries.
• Do not stand or sit on, nor hang down from the unit as
this may cause it to fall down or drop, resulting in
personal injury and/or property damage.
• Use nuts and bolts that are appropriate for the ceiling's
or wall's structure and composition. Failure to do so may
cause the speaker to fall, resulting in material damage
and possible personal injury.
• Have the unit periodically checked by the shop from
where it was purchased. Failure to do so could result in
the speaker falling off due to damage or corrosion to the
speaker or its mounts, and possible personal injury.
• Tighten each nut and bolt securely. Ensure that the
bracket has no loose joints after installation to prevent
accidents that could result in personal injury.
• Attach the safety wire to the unit when mounting in
locations high above the ground. Failure to do so could
result in personal injury if the speaker should later fall for
any reason.
4.2. Wall Mounting – With Supplied Bracket
4.4. Mounting with Other Brackets
The following table shows the brackets that can be used for
the BS-1030 Series Speakers. When using these brackets,
refer to their corresponding instruction manuals.
Step 1. Attach the bracket to the speaker using the
supplied hardware.
Usable Brackets
BS-1030B
OK
BS-1030W
OK
Bracket
(standard accessory)
Speaker Mounting
Bracket SP-410
Speaker
Speaker Mounting
Bracket SP-420
OK
OK
OK
Wall/Ceiling Mounting
Bracket WCB-12
Wall/Ceiling Mounting
Bracket WCB-12W
Table Mounting
Bracket TMB-1
Table Mounting
Bracket TMB-1W
OK
OK
Plain washer
(standard accessory)
5. OUTDOOR INSTALLATION
PRECAUTIONS
Machine screw
(standard accessory)
The speaker's splash-proof construction permits it to be
installed outdoors, such as under eaves and other locations
where the speaker is not directly exposed to the elements.
However, because the splash-proof feature is strictly
dependent on speaker orientation, follow the mounting
instructions below.
Step 2. Mount the speaker in the desired location using the
mounting holes made in the bracket.
Note
Bracket mounting hardware is not supplied with the unit.
Referring to the bracket's dimensional diagram, prepare
the correct type of screws or bolts appropriate to the wall
material.
5.1. Vertical Installation
Horizontal
4.3. Mounting on the Optional ST-16 Speaker Stand
Step 1. Attach the bracket to the speaker using the
supplied hardware. (Refer to Section "4.2. Wall
Mounting – With Supplied Bracket.")
Face-down
Install the speaker so that its front panel
orientation stays in the above range.
Step 2. Mount the speaker to the speaker stand through
Install with the logo mark located at the bottom
of the front panel.
the bracket's mounting holes.
5.2. Horizontal Installation
Speaker
Bracket
Horizontal
(supplied with
the speaker)
Butterfly nut
(supplied with
the ST-16)
Face-down
Install the speaker so that its
front panel orientation stays in
the above range.
Bracket
(supplied with the ST-16)
Install with the logo mark located
at the right of the front panel as
viewed from the front.
Washer
ST-16
(supplied with
(optional)
the ST-16)
The logo mark can be changed
to correct its orientation.
Hexagonal-head bolt
(supplied with the ST-16)
Note
The splash-proof function will not work with any other
installation method than those referred to above.
6. DIMENSIONAL DIAGRAM
7. SPECIFICATIONS
• Speaker
• Specifications common to both the BS-1030B
and BS-1030W
Unit: mm
Enclosure Type
Rated Input
2-way bass-reflex system
30 W
Rated Impedance
8 Ω
High impedance (100 V line):
330 Ω (30 W), 500 Ω (20 W), 670 Ω
(15 W), 1 kΩ (10 W), and 2 kΩ (5 W)
High impedance (70 V line):
170 Ω (30 W), 250 Ω (20 W), 330 Ω
(15 W), 500 Ω (10 W), and 1 kΩ (5 W)
Note: Impedance is changeable by
means of the rotary switch.
90 dB (1 W, 1 m)
600
Sound Pressure
Level
Frequency Response 80 – 20,000 Hz
Internal Speakers
Low frequencies:
196
150
12 cm dynamic speaker
High frequencies:
2.5 cm dome tweeter
– 10°C to +50°C
Operating
Temperature Range
Splash-Proof Capability
IP-X3 (when the angle is specified in
vertical or horizontal installation)
196 (w) x 290 (h) x 150 (d) mm
Refer to the table below.
Dimensions
Finish
Weight
2.5 kg (speaker only)
50
60
[Finish]
Case: ABS resin, black, paint
BS-1030B
BS-1030W
Grille: Pre-coated steel plate, black, paint
Bracket: Pre-coated steel plate, black, paint
Case: ABS resin, white, paint
Grille: Pre-coated steel plate, white, paint
Bracket: Pre-coated steel plate, white, paint
• Bracket (standard accessory)
Note: The design and specifications are subject to change without
notice for improvement.
• Accessories
Bracket .................................................. 1
M5x10 machine screw ........................... 2
M5 plain washer .................................... 2
17- ø9
50
100
262
Printed in Indonesia
533-06-062-5A
|