®
™
Bluetooth Stereo Headset Kit for iPod
Handsfree Headset + Adapter for iPod
US GB
User Manual
naviPlay Bluetooth Stereo Headset, NSH.P10
naviPlay Bluetooth Stereo Adapter for iPod, NIA.S10-U
Read these instructions before operating.
Follow all instructions.
Heed all warnings.
Keep these instructions for future reference.
Important Safety Information
Read these instructions before operating.
Follow all instructions.
Heed all warnings.
Keep these instructions for future reference
Caution: Risk of electric shock. Do not tamper with, modify, open or disassemble.
Do not use near water or in wet environment.
Do not immerse in water or any liquid.
Clean only with dry cloth.
Use only as directed in this user manual or as instructed by manufacturer.
Do not install or use near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
Refer all servicing to qualified service personnel.
Caring for the Environment by Recycling
When you see this symbol on a product, do not dispose the product with household waste.
Recycling Mobile Phones and Accessories
Do not dispose of mobile phones or electrical accessories, such as chargers or headsets, with your
household waste. In some countries or regions, collection systems are set up to handle electrical and
electronic waste items. Contact your regional authorities for more details.
Important Safety Information
3
Lithium Battery Safety Precautions
For the safe use of lithium-polymer and lithium-ion batteries, always follow the instructions
provided below. Improper handling of lithium batteries may result in injury or damage from
electrolyte leakage, heating, ignition, or explosion.
Danger:
• Never use the batteries with anything other than specifically designed equipment.
• Always use the battery charging method provided with the device.
• Never impact, pierce, or crush the battery.
• Handle a damaged or leaking battery with extreme care. If you come in contact with the
electrolyte, wash the exposed area with soap and water. If it contacts the eye, flush the eye
with water for 15 minutes and seek medical attention.
• When discarding a battery, contact your local waste disposal provider regarding local
restrictions on the disposal or recycling of batteries.
• Never disassemble or modify the battery. The battery contains a circuit designed to enhance
safety. Damaging this circuit may cause overheating, fire, or bursting.
• Never expose or charge a battery under high-temperature conditions, such as near a fire or in
the direct sunlight. If the ambient temperature is too high, the protection circuit may be
actuated, preventing further charging, or damaged.
• Never short-circuit the battery by connecting the positive and negative terminals with a metal
material. Do not store or carry the battery where it could come into contact with metal
objects such as a key chain or necklace.
4
Important Safety Information
• Never allow the battery to get wet or be immersed in water.
• Do not place the battery in a microwave oven or high-pressure container.
• Stop charging if the battery is not charged after the prescribed charge time.
• If leakage of the electrolyte occurs, or if there is an offensive odor, immediately keep the
battery away from any source if fire or spark.
If, during use, charging, or storage, you become aware of any abnormal phenomena, such as
odor, discoloration, or deformation, disconnect the device or from charger and stop using
immediately.
Important Safety Information
5
Requirements
The naviPlay Bluetooth Stereo Headset requires the following types of devices for proper function:
For Stereo Music Streaming: a Bluetooth-enabled stereo music source supporting A2DP profile
(Advance Audio Distribution Protocol) – Example: TEN naviPlay Bluetooth Adapter for iPod
For Handsfree/Headset Function: a Bluetooth-enabled mobile phone supporting Handsfree or
Headset profiles
For Remote Control: a Bluetooth-enabled stereo music source supporting AVRCP profile (Audio
Video Remote Control Protocol) – Example: TEN naviPlay Bluetooth Adapter for iPod
For updating the software on the naviPlay Bluetooth Stereo Headset, see “Updating naviPlay
Firmware” for additional requirements
The naviPlay Bluetooth Adapter for iPod requires the following devices for proper function:
For Stereo Music Streaming: a Bluetooth-enabled stereo music receiver (e.g. headphones,
audio system) supporting A2DP profile (Advance Audio Distribution Profile) – Example: TEN
naviPlay Bluetooth Stereo Headset or TEN naviPlay Bluetooth Stereo Remote
For Remote Control: a Bluetooth-enabled device supporting the AVRCP profile (Audio Video
Remote Control Protocol)
Apple iPod with Dock Connector: iPod w/Video, iPod nano, U2 iPod, iPod w/Color Display, iPod
photo, iPod mini, iPod w/Dock Connector
6
Requirements
Quick Start
Congratulations and thank you for purchasing the naviPlay Bluetooth Stereo Headset, designed
specifically for enjoying your music free from any wire or cable, and free from worry of missing a
phone call. Using wireless Bluetooth technology, the naviPlay Stereo Headset and a Bluetooth-
enabled music source work together to provide digital audio streaming, giving you untethered use
and control of your music.
The naviPlay Stereo Headset is designed for active listeners, freeing you from the cumbersome
cable connection between your iPod and headphones. The naviPlay Stereo Headset can also be
used as a wireless headset with your Bluetooth-enabled mobile phone.* Effortlessly switch
between listening to music to taking calls without having to remove your headphones or
scramble for your phone. Use it on a treadmill at the gym, take it with you cycling…anytime
being tied to your iPod would limit your range of motion or expose the iPod to risk. The
possibilities are limitless.
The great thing about naviPlay is that it's ready to use right out of the box. There's no software
to load, nothing to configure to enjoy your music wirelessly. Just charge the adapter and headset
and travel with your tunes.
*Setup required to use with mobile phone. Does not work with all Bluetooth-enabled phones.
Quick Start
7
naviPlay Stereo Headset Contents
Make sure you have received the following items:
naviPlay Headset
Headset USB Charging Cable
User Manual
naviPlay iPod Adapter
Clips for iPod Models
8
Quick Start
naviPlay Stereo Headset at a Glance
naviPlay Adapter
Battery Pack
Clip Attachment
Charge Light
Status Light
iPod Dock Connector
Flip Stand
Power
Adapter Base
naviPlay Headset
Power;
Play/Pause
Charging Light
Charging Socket
Status Light
Call Button
Microphone
Quick Start
9
Setting up naviPlay
To set up and use your naviPlay Stereo Headset, you first need to charge the Adapter and the
Headset for at least one hour.
Step 1: Charge the naviPlay Adapter and Headset
Using the iPod Dock Connector to USB or Firewire cable (included with iPod), connect the
naviPlay Adapter to your computer or iPod Power Adapter (optional) to charge. Use the included
USB Charging cable to charge the naviPlay Headset by connecting to your computer or USB
power adapter (optional). You can also charge the iPod at the same time by docking your iPod in
the naviPlay Adapter, however, note that charging time may increase significantly depending on
the iPod battery level. See "Step 2: Attach iPod to naviPlay Adapter.
naviPlay
Headset
Note: Firewire
charging will be
naviPlay Adapter
significantly faster
than USB charging.
Charging the naviPlay
Adapter alone will be
faster than with iPod
docked in the Adapter.
iPod USB Cable
or FireWire
(included w/iPod)
USB Charging
Cable
Computer
Without iPod docked, the internal battery of the naviPlay Adapter will be about 80 percent
charged after 2 hours, and fully charged after about 4 hours. The naviPlay Headset internal
battery will be about 80 percent charged after 2 hours, and fully charged after about 4 hours.
While charging, the charge light will remain constant red. When the Headset is fully charged, its
light will turn green. When the iPod Adapter is fully charged, its light will turn off.
The status light will blink red when the naviPlay iPod Adapter or Headset needs to be recharged.
10
Quick Start
Step 2: Attach iPod to naviPlay Adapter
1. Find the clip for your iPod among the six clips
provided. The clips are labeled for the various iPod
models. Attach the clip to the naviPlay Adapter. For
iPod nano, insert the clip adapter (8) into iPod mini
clip (3) before attaching to the naviPlay Adapter.
iPod Clip
iPod Model
iPod Clip
iPod w/Dock Connector 10/15/20GB
iPod w/Dock Connector 30/40GB
iPod mini
1
2
3
naviPlay Adapter
Click Wheel iPod 20GB/U2
Click Wheel iPod 40GB
4
5
iPod Photo 30GB/Color Display 20GB
iPod Photo 40/60GB/Color Display 60GB
iPod nano
6
7
3+8
9
iPod w/Video 30GB
iPod w/Video 60GB
10
2. Slide your iPod into the clip until the dock connector port and
the connector on the naviPlay Adapter join. Adjust the Adapter
base forward or backward to align the dock connectors. Press
the iPod down until it meets the top of the Adapter base.
Tip: You can still sync your iPod with your computer while it is
docked in the naviPlay Adapter. Connect the iPod USB or Firewire
cable to the dock connector socket on the back of the naviPlay
Adapter. Note that the iPod will not play music while it is syncing
with the computer, so the naviPlay cannot stream music.
Quick Start
11
Step 3: Turn on naviPlay Adapter and Headset
Press the Power/Play/Pause button on the naviPlay Headset to turn it on. You should hear the
naviPlay startup tones. Press the Power button on the naviPlay Adapter to turn it on. Turn on the
iPod if it is still off.
Both the naviPlay Headset and the Adapter status lights should blink green and amber at first,
then blink just green once the wireless connection between them has been established.
To preserve the battery charge, turn off the naviPlay devices when not in use. Press and hold
down the POWER button until the status light is constant amber, then release. The adapter also
turns itself off when it has been removed from the iPod after three minutes.
Step 4: Listen to Your Music
Select the audio track or playlist on your iPod and press PLAY/PAUSE on the iPod or naviPlay
Headset. Adjust the volume using the naviPlay Headset volume controls.
12
Quick Start
Using naviPlay
You can control the playback of the music using either the naviPlay Headset remote controls or
the iPod controls. Here's a quick reference to the naviPlay Headset controls for music.
naviPlay Remote Controls
Play/pause music.
Adjust the volume.
Press down on the POWER/Play/Pause button.
Press the VOLUME UP (+) or VOLUME DOWN (-) to
adjust the volume by one level. Press and hold in either
direction to gradually adjust the volume level.
Play the current song again.
Play the next song.
Press the PREVIOUS TRACK once.
Press the NEXT TRACK.
Play the previous song.
Scan through a song.
Press the PREVIOUS TRACK twice.
Press and hold the NEXT TRACK or PREVIOUS TRACK
until the iPod starts to scan.
Turn On
Turn Off
Press POWER/Play/Pause button.
Turn Off Press and hold POWER/Play/Pause button until
status light turns constant amber.
Play/Pause
Volume Up
Previous Track
Next Track
Volume Down
Status Light
Call Answer/End
Using naviPlay
13
Status Indicator Chart
As you use your Stereo Kit, you will see various status lights on both the Adapter and Headset.
Here's a quick reference:
Pattern
Mode
Status
Green Slow Blink
Normal Operation
Everything normal, connection
established
Green/Amber Slow Blink
Red Slow Blink
Normal Operation
Normal Operation
Pairing Mode
Establishing Bluetooth connection
Low battery warning
Green/Amber Fast Blink
Discoverable, searching for other
devices
Red Constant
Pairing Mode
Failed
Amber Double Blink
Green Double Blink
Red Constant
Firmware Update Mode
Firmware Update Mode
Firmware Update Mode
Firmware Update Mode
Ready for transfer
Transfer in progress
Failure
Green Constant
Success
14
Using naviPlay
Using the naviPlay Adapter Flip Stand
1. Slide the iPod into the naviPlay
Adapter.
2. Pull out the stand provided on
the back of the Adapter.
To return the stand to its upright
position, pull out on the insides
of the stand (A) and then pull up
(B).
naviPlay Adapter
Using naviPlay
15
UsingnaviPlayHeadsetwithOtherBluetooth-EnabledDevices
The naviPlay Stereo Headset is designed for different uses, including as a wireless headset for
Bluetooth-enabled mobile phones. Since the naviPlay Stereo Headset has a built-in microphone,
you can use it to answer your phone calls.
Other products that are Bluetooth-certified to support stereo audio and remote control will also
work with the naviPlay iPod Adapter or the naviPlay Stereo Headset. You can listen to music
stored on Bluetooth Stereo enabled personal computers, PDAs, or mobile phones with the
naviPlay Stereo Headset. You will be able to play your iPod music through Bluetooth stereo
enabled speakers, home stereo systems, stereo headphones and even car stereo systems using
the naviPlay iPod Adapter. The possibilities are limitless!
Using the naviPlay Headset With Bluetooth-Enabled Mobile Phones
The microphone built into the naviPlay Stereo Headset allows it to be used as a wireless
headset with Bluetooth-enabled mobile phones. Now, while you are enjoying your music from
the iPod, you won't miss a call or have to quickly remove your headphones just to answer the
call. You will hear ringtones through the Headset when your phone is receiving a call. A push of
the Call button will accept the call and switch the Bluetooth connection to your phone.
Depending on your phone, you can choose not to accept the call by pushing the
Power/Play/Pause button to reject the call. When you are done with the call, push the Call button
to hang up and resume listening to music.
Note that if you are on a call for more than 3-5 minutes, the iPod and the naviPlay Adapter will
go into sleep mode to conserve power. You may have to turn on the naviPlay Adapter to resume
listening to music. During phone calls the volume in the right headset speaker is automatically
limited to minimize potential echo effect for callers.
16
Using naviPlay Headset with Other Bluetooth-Enabled Devices
Setting up the naviPlay Headset to work with your mobile phone:
You will only have to do this setup procedure once to pair the naviPlay Headset with your mobile
phone. After this initial setup is complete, the connection between the naviPlay Headset and
your phone should be automatic.
1. IMPORTANT: Turn off both the naviPlay Headset and the naviPlay Adapter before attempting
pairing process. For best results, turn off other nearby Bluetooth-enabled devices also.
2. Press the POWER/Play/Pause button on the naviPlay Headset and hold it down for about eight
seconds until the status light quickly blinks amber and green. This puts the naviPlay Headset
in discoverable/pairing mode so that other Bluetooth devices can discover and pair to it.
3. Put your Bluetooth-enabled mobile phone into handsfree/headset pairing mode. Refer to the
documentation that came with your Bluetooth mobile phone for exact procedure and details.
4. Place the naviPlay Headset near the mobile phone. When prompted, enter “0000” for the
passkey to complete the pairing process. On your phone, select "naviPlay Stereo Headset" as
the device to connect/pair with.
When the connection process is complete, the status light on the naviPlay Headset blinks
green slowly, then alternates between slowly blinking amber and green. The naviPlay Headset
will now connect to the previously configured music source as well as your mobile phone.
If the pairing process fails the status light will change to constant red, then alternates
between slowly blinking amber and green. You can attempt the process again from step one
Using naviPlay Headset with Other Bluetooth-Enabled Devices
17
About Handsfree vs. Headset
Some Bluetooth-enabled mobile phones support only Headset mode, while most newer phones
support Handsfree mode. Refer to your phone's documentation to determine which modes are
supported. The newer Handsfree mode includes additional functions such as call reject. The
naviPlay Headset supports both Handsfree and Headset phones, with some differences in
functionality.
Occasionally, you may have to manually reconnect the naviPlay Headset with some mobile
phones. On some phones, you will have to initiate the reconnection from the phone.
naviPlay Handsfree/Headset Functions:
Function
Answer Call
End Call
Handsfree Mode
Headset Mode
Press Call Answer/End Button
Press Call Answer/End Button
Press Power/Play/Pause Button
Press Call Answer/End Button
Press Call Answer/End Button
Not possible
Reject Call
Last Number Redial Press and hold Call Answer/End until tone Not possible
Connect to Phone Press Call Answer/End Button Press Call Answer/End Button
Call Reject
naviPlay Headset
Call Answer/End
Using naviPlay Headset with Other Bluetooth-Enabled Devices
18
naviPlay Stereo Headset Indicator Tones
The naviPlay Headset will play certain tones to notify or confirm certain events.
Event
Tone Description
Startup Tones
Max Volume
5 notes played upon successful power on
Single high tone played when maximum volume setting
is reached - heard when pressing Volume Up button.
Phone Link Lost
High-low tones played when Bluetooth connection to
mobile phone is terminated - usually when out of range or phone is
powered off.
Phone Link Search
Series of low tones played when trying to establish Bluetooth connection
to mobile phone - user initiated by pressing Call Button
Phone Link Found
Phone Link Fail
Low-high tone pair played when connection to phone is established
High-low tone pair played when connection to
phone can not be established
Using naviPlay Headset with Other Bluetooth-Enabled Devices
19
Using the naviPlay Adapter With Other Bluetooth Devices
The naviPlay Adapter and Headset are “paired” at the factory to automatically communicate with
each other. You can also use the naviPlay adapter with other Bluetooth stereo headphones. Go to
www.tentechnology.com for the latest information on compatible Bluetooth-enabled devices.
The headphones must support A2DP (Advanced Audio Distribution Profile) for audio and AVRCP for
remote control.
To use the naviPlay Adapter with other Bluetooth-enabled headphones, you must first pair the
two devices. To pair the adapter to the headphones:
1. IMPORTANT: Turn off naviPlay Adapter before attempting pairing process. For best results, turn
off other nearby Bluetooth-enabled devices also.
2. Put the headphones in discoverable mode. (Refer to the documentation that came with your
headphones for details.)
3. Place the headphones near the naviPlay adapter. Make sure that no other nearby Bluetooth-
enabled headphones are turned on.
4. Press the POWER button on the naviPlay adapter and hold it down for at least eight seconds,
or until the status light alternates between quickly blinking amber and green. This initiates the
pairing process on the naviPlay adapter.
The naviPlay Adapter will search for all Bluetooth-enabled devices nearby. The naviPlay Adapter
configures itself to connect to the nearest headphones it discovers. When the connection is
complete, the status light blinks green slowly.
If the connection process fails, the status light glows red continuously for five seconds. The
naviPlay adapter will continue to connect to the previously configured headphones.
20
Using naviPlay Headset with Other Bluetooth-Enabled Devices
Using the naviPlay Headset With Other Bluetooth-Enabled Devices
The naviPlay Adapter and Headset are automatically configured to connect to each other.
However, you can connect the naviPlay Headset to any Bluetooth-enabled music device (such as
a PC, PDA, MP3 player, or mobile phone) that supports the Advanced Audio Distribution Profile
(A2DP). Although you can use the naviPlay Headset with other Bluetooth music devices, you will
get the best performance when using it with the naviPlay Adapter.
To use the naviPlay Headset with different Bluetooth music devices:
1. IMPORTANT: Turn off the naviPlay Headset before attempting pairing process. For best results,
turn off other nearby Bluetooth-enabled devices also.
2. Press the POWER button on the naviPlay Headset and hold it down for eight seconds, or until
the status light alternates between quickly blinking amber and green. This puts the naviPlay
Headset in discoverable mode, so that other Bluetooth devices can discover and connect to it.
The blinking status light indicates that the naviPlay Headset is waiting for connection from a
Bluetooth-enabled music device.
3. Put the Bluetooth music device in pairing mode. (See the documentation that came with your
Bluetooth music device for details.)
4. Place the naviPlay Headset near the music source device.
Make sure that no other nearby Bluetooth-enabled music devices are turned on. When the
connection process is complete, the status light blinks green slowly. If the connection process
fails, the status light glows red continuously for five seconds. The naviPlay Headset continues to
connect to the previously configured music source.
Using naviPlay Headset with Other Bluetooth-Enabled Devices
21
Updating naviPlay Firmware
New versions of firmware may be available to enable features, optimize performance and/or fix
problems. You can update the firmware on the naviPlay adapter and naviPlay Headset when a
Download the available firmware update to your computer and follow the instructions in the “READ
ME” file. The firmware must be transferred “over-the-air” via Bluetooth to the naviPlay device. You
will need a Bluetooth-enabled PC or Macintosh that supports the Object Push Profile (OPP).
Setting up the naviPlay Device for Firmware Update
1. Turn on the naviPlay device that you are updating (Adapter or Headset). For best results, turn
off other nearby Bluetooth devices and fully charge your naviPlay device before attempting
firmware update. Better yet, keep it plugged into the charger.
2. Press and hold the POWER button for eight seconds to put the device in firmware update
mode. The status light shows quick double-blinks in amber as soon as the Adapter is in
firmware update mode. Release the POWER button after you see the amber double-blinks.
Updating naviPlay Firmware from a Bluetooth-Enabled Windows PC
Refer to the documentation that came with your PC or Bluetooth hardware for sending a
business card file (.vcf) to another Bluetooth device.
Updating naviPlay Firmware from a Bluetooth-Enabled Macintosh
The following Macintosh operating systems are required to update firmware over the Internet:
Mac OS X 10.2.8,10.3.1 or later, or 10.4 or later.
22
Updating naviPlay Firmware
To update the firmware:
2. Click the Bluetooth icon in the menu bar and select Send File.
3. Browse and select the firmware file that you just downloaded.
4. Click Send.
5. Click the Search button on the your computer to find the naviPlay device.
6. Select the naviPlay device after it has been discovered and displayed in the list. If you are
updating firmware for the naviPlay Stereo Headset, you will see the name naviPlay Stereo
Headset in the list of devices. If you are updating firmware for the naviPlay iPod adapter, you
will see the name naviPlayAdapter.
7. Click Send.
Firmware Update Tips (Windows + Mac)
When the firmware update has started, the status light double-blinks green slowly. After the
firmware update is complete, the status light glows green continuously for five seconds. This
indicates a successful firmware update.
If the firmware update fails the status light glows red continuously for five seconds, and then the
adapter switches off. If the adapter is then switched on, it goes into firmware update mode
automatically (you will see amber light double blinks), until the firmware update is successfully
completed.
Important! When the firmware upload process begins, the old firmware is first erased on the
device. If the upload fails, the device will not operate until new firmware is uploaded
successfully.
Updating naviPlay Firmware
23
Troubleshooting
The naviPlay Headset does not power on or respond to button presses.
Make sure the battery is charged.
No audio is heard from the naviPlay Headset.
Make sure your iPod, naviPlay Adapter and Headset are all on and connected. Check the status
light on the naviPlay Adapter and Headset. Verify that the naviPlay Adapter and Headset are
within range of each other. Check the volume on the naviPlay Headset. Verify the iPod is
outputting audio through the iPod headphone jack.
Audio suddenly stops.
The Headset may be out of range from the adapter. The audio streaming should resume if you
move back into range within three minutes.
Can not pair with mobile phone.
enabled mobile phones. Note that actual performance and features available vary between
phone models.
24
Troubleshooting
AbouttheTechnologyBehindthenaviPlayStereoHeadset
The naviPlay Stereo Headset uses Bluetooth technology to provide digital audio quality (44.1KHz
and 48KHz, 16-bit stereo) wireless streaming from your Apple iPod to the naviPlay Headset.
Bluetooth is a radio technology for short-range wireless mobility, eliminating cables, wires, and
cords between enabled devices, such as mobile phones and headphones. Bluetooth facilitates
fast, secure transmissions of both audio and data, even when the devices are not in line of sight
of each other. The naviPlay Stereo Headset devices are Bluetooth version 1.2 certified, and
support the Advanced Audio Distribution Profile (A2DP), Audio Video Remote Control Profile
(AVRCP) and Object Push Profile (OPP).
About the Technology Behind the naviPlay Stereo Headset
25
Improving Wireless Effectiveness
Radio noise from other nearby devices, such as a microwave oven or Wi-Fi network, or from a
signal absorbing or reflecting object in between the naviPlay devices, may affect the bandwidth
of naviPlay's wireless music streaming. The naviPlay devices use Bluetooth technology to
communicate, which requires full bandwidth to stream music wirelessly.
Under typical conditions, the naviPlay devices have a range of about 24-30 feet (8-10 meters).
The location and orientation of each naviPlay device can affect the wireless range. For best
results, place the naviPlay adapter off the ground, away from other signal absorbing materials.
Changing the orientation of either naviPlay device can also affect the range.
tips and hints.
26
Improving Wireless Effectiveness
Technical Specifications
Model: NSH.P10
TEN Technology naviPlay Bluetooth Stereo Headset
General Radio
Battery
Carrier Frequency: 2.4 ~ 2.483GHz
Class 2 Radio
Built-in, not user serviceable
Rechargeable lithium-polymer 3.7V 540mAh
8 hours continuous operation (at maximum
volume and 2 meters range)
Wireless Range
Outdoors: 3–10 meters (9–30 feet)
Indoors: 3–10 meters (9–30 feet)
Actual range depends on environmental
Power Consumption
220mW
factors: orientation of devices relative to each Power Input
other, obstructions and enclosures, radio
frequency noise, and interference.
5V 0.5A 2.5W
Temperature
Bluetooth
During Battery Charging: 0º–45º C
Normal Operation: -10º–55º C
Storage: -20º–50º C
Bluetooth identifier:
Bluetooth 1.2 Certified
Advanced Audio Distribution Profile (A2DP)
Audio Video Remote Control Profile (AVRCP)
Object Push Profile (OPP)
Headset Profile (HSP)
Weight
117 grams/4.125 ounces
Handsfree Profile (HFP)
Dimensions (Overall)
181.4mm x 173.9mm x 68.0mm
Audio Codec SBC
Audio Input
Built-in microphone
Technical Specifications
27
Model: NIA.S10-U
TEN Technology naviPlay Bluetooth iPod Adapter
General Radio
Battery
Carrier Frequency: 2.4 ~ 2.483GHz
Class 2 Radio
Built-in, not user serviceable
Rechargeable lithium-polymer 3.7 V 540 mAh
8 hours continuous operation (at maximum
volume and 2 meters range)
Wireless Range
Outdoors: 3–10 meters (9–30 feet)
Indoors: 3–10 meters (9–30 feet)
Power Consumption
220mW
Actual range depends on environmental
factors: orientation of devices relative to each Power Input
other, obstructions and enclosures, radio
frequency noise, and interference.
iPod USB or Firewire cable for recharging and
operation
5-12VDC Max 1.0A
Bluetooth
Bluetooth identifier: B01960
Bluetooth 1.2 Certified
Advanced Audio Distribution Profile (A2DP)
Audio Video Remote Control Profile (AVRCP)
Object Push Profile (OPP)
Temperature
During Battery Charging: 0º–45º C
Normal Operation: -10º–55º C
Storage: -20º–50º C
Weight
58 grams/2.0 ounces
Audio Codec
SBC
Dimensions (Overall)
85mm x 66mm x 27.5mm
Audio Input
Line-level analog (from Apple iPod)
28
Technical Specifications
Regulatory Information
Exposure to Radio Frequency Radiation
The radiated output power of the TEN Technology naviPlay Bluetooth wireless radio Class 2 is far
below the FCC, Industry Canada, and European Union radio frequency exposure limits.
Nevertheless, the wireless radio shall be used in such a manner that the potential for human
contact during normal operation is minimized. The internal wireless radio operates within
guidelines found in radio frequency safety standards and recommendations, which reflect the
consensus of the scientific community.
The level of emitted energy emitted is far less than the electromagnetic energy emitted by
wireless devices such as mobile phones. However, the use of wireless radios may be restricted
in some situations or environments, such as aboard airplanes. If you are unsure of restrictions,
you are encouraged to ask for authorization before turning on the wireless radio.
The FCC, Industry Canada and European Union have set a general guideline of 20 centimeters (8
inches) separation between the device and the body, for use of a wireless device near the body.
This device should be used more than 20 centimeters (8 inches) from the body when wireless
devices are on.
FCC Part 15 Radio Frequency Interference Statement
This device complies with Part 15 of the FCC rules. Operation is subject to the following two
conditions:
• This device may not cause harmful interference.
• This device must accept any interference received, including interference that may cause
undesired operation.
Regulatory Information
29
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet that is on a circuit different from the receiver.
• Consult the dealer or an experienced radio/TV technician for help.
CAUTION:
Pursuant to Part 15.21 of the FCC rules for intentional or unintentional radiators, any changes or
modifications not expressly approved by the party responsible for compliance could void the
user's authority to operate this equipment.
Industry Canada ICES-003 Emission Compliance Statement
This Class B digital apparatus meets the requirement of the Canadian Interference-Causing
Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du règlement sur le
matériel brouiller du Canada.
30
Regulatory Information
European Radio Approval Information
The TEN Technology naviPlay Bluetooth devices are low-power, wireless communication devices,
operating in the 2.4 GHz band, intended for home or office use. The power output of this device
is well below the RF exposure limits as set by the European Commission through the R&TTE
directive.
The TEN Technology naviPlay Bluetooth devices can be operated in the following European Union
and European Economic Area countries: Austria, Belgium, Cyprus, Czech Republic, Denmark,
Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Liechtenstein,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia,
Spain, Sweden, Switzerland and the United Kingdom.
CE Declaration of Conformity
TEN Technology naviPlay Bluetooth devices are in conformity with the following directives and other
normative documents:
R&TTE Directive 1999/5/EC
• ETSI EN 300 328
• ETSI EN 301 489-1
• ETSI EN 301 489-17
Low Voltage Directive (Safety) 73/23/EEC as per EN 60950.
This product is also compliant with the maximum sound pressure level as specified by the EN
50332-2 standards.
Regulatory Information
31
© Copyright 2006 TEN Technology, Inc. All rights reserved. TEN Technology word mark, TEN Technology
logo and naviPlay are trademarks of TEN Technology, Inc., registered in the US and other countries.
Apple, the Apple logo, and iPod are trademarks of Apple Computer, Inc., registered in the US and other
countries. Bluetooth is a trademark owned by Bluetooth SIG, Inc. USA, and licensed to TEN Technology,
Inc. All other products or name brands are trademarks of their respective holders.
TEN-210-0015
B01960
B02615
Printed in China
004NYCA0322
FCC ID SIO-NSHP10
IC 5344A-NSHP10
|